Nobody is using this legacy call. Just remove it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L1 was removed. So, the code there is just dead code.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After registering the cdev, it would be possible do have an open on it.
In a matter of fact, some versions of udev do this. So, move registration
to the end and protect it with a mutex.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx88-video has locks. don't use the locked ioctl version, as
it is not needed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adds support for Pixelviex Xcapture USB grabber device.
This device has one composite and one s-video entry
only, plus a button.

For now, the button is not supported.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some devices don't need to use it. So allow to just disable this logic.
Having it enabled on some devices cause power management to complain,
generating error -71.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead of per-model tests all over the code, use some parameters
at the board entries to describe the model variants for:
	- devices with 417 MPEG encoder;
	- devices that use external AV;
	- devices where vbi VANC endpoint doesn't work;
	- devices with xc5000 that require different IF
	  initialization (and probably will cover also
	  xc3028).
	- devices with xceive tuner that require a reset
	  during init.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The check for xc5000 assumes that the tuner will always
be using the same bus and will have the same address.
As those are configurable via dev->board, it should use,
instead, the values defined there.

Also, a similar type of test will be needed by other
tuners (for example, for TUNER_XC2028)
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Just a cleanup patch. Removes one indent level by moving
the return -ENODEV to happen before the device register
logic, if the interface is not the audio/video (int 1).
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Unable to test this due to lack of hardware.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested with a Logitech QuickCam Pro 4000.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/vivi.c:1059: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also fixed a memory leak in the probe function if an error occurred.
The gain control range was also fixed (a proper range from -64 to 64).
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When a device is not detected, the driver prints a warning message.
That's ok, except for the fact that, even on newer devices that have
eeprom but aren't yet supported, it prints a message saying that the
device doesn't have eeprom.

Fix it by having a separate message for devices with eeprom, but not
yet known by the driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make vivi use videobuf2 in place of videobuf.
Signed-off-by: NPawel Osciak <p.osciak@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add I2C/V4L2 subdev driver for Siliconfile NOON010PC30 CIF camera.
The driver implements basic functionality, i.e. CIF/QCIF/QQCIF
resolution and color format selection, automatic/manual color
balance control. Other functions like cropping, rotation/flip,
exposure etc. can be easily implemented if needed.
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When is called fimc_stop_capture, it seems that wait_event_timeout
used improperly. It should be wake up by irq handler.

Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: NSungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the value of FIFO_CTRL in MSCTRL.
Main-scaler has the value to specify a basis FIFO control of input DMA.

The description of FIFO_CTRL has been changed as below.
0 = FIFO Empty (Next burst transaction is possible when FIFO is empty)
1 = FIFO Full (Next burst transaction is possible except Full FIFO)

Value '1' is recommended to enhance the FIMC operation performance.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds callback functions, stop_streaming and job_abort,
to abort or finish any DMA in progress. stop_streaming is called
by videobuf2 framework and job_abort is called by m2m framework.
ST_M2M_PEND state is added to discard the next job.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1);  /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1);  /* Out of Vertical scale range}

fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.

The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0],   MainVerRatio_ext = CIEXTEN[5:0]

This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Map all (0, 90, 180, 270) deg counterclockwise rotation and
horizontal and vertical flip controls to (0, 90) deg rotation,
horizontal and vertical flip transformations available
in the device.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Increase the input DMA "successive burst count" to default
value 4 to improve DMA performance. Minor cleanup.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prevent VIDIOC_STREAMON failing when s_stream callback is
not implemented by a sensor subdev driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>