Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAnji jonnala <anjir@codeaurora.org>
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports.  USB hardware is put into low power
mode when connected to a dedicated charging port.  vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).

The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY).  The PHY vendor and product id registers are not
implemented in the above chipsets.  Hence PHY type is passed via platform
data.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Signed-off-by: NAnji jonnala <anjir@codeaurora.org>
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the UHCI part of the GRLIB GRUSBHC controller
found on some LEON/GRLIB SoCs.

The UHCI HCD previously only supported controllers connected over PCI.
This patch adds support for the first non-PCI UHCI HC. I have tried to
replicate the solution used in ehci-hcd.c.

Tested on GR-LEON4-ITX board (LEON4/GRLIB with GRUSBHC) and x86 with Intel
UHCI HC.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.

This patch also extends the uhci_{read,write}* functions to allow accesses
to registers not mapped into PCI I/O space. This extension also includes
the addition of a void __iomem pointer to the uhci structure.

A new Kconfig option is added to signal that the system has a non-PCI HC.
If this Kconfig option is set, uhci-hcd.c will include generic reset functions
for systems that do not make use of keyboard and mouse legacy support. PCI
controllers will still always use the reset functions from pci-quirks

This patch is followed by a patch that adds bus glue for the first non-PCI
UHCI HC.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.

This patch replaces in{b,w,l} and out{b,wl} with calls to local inline
functions. This is done so that the register access functions can be
extended to support register areas not mapped in PCI I/O space.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.

This patch moves PCI specific functions to uhci-pci.c and includes
this file in uhci-hcd.c. It also renames the function uhci_init to
uhci_pci_init.

uhci_init/uhci_pci_init is modified so that the port-detection logic
is kept in a new separate function uhci_count_ports() in uhci-hcd.c.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.

This patch fixes the following warnings from checkpatch:

ERROR: switch and case should be at the same indent
+   switch (to_pci_dev(uhci_dev(uhci))->vendor) {
+       default:
[...]
+       case PCI_VENDOR_ID_GENESYS:
[...]
+       case PCI_VENDOR_ID_INTEL:

WARNING: static char array declaration should probably be static const char
+   static char bad_Asus_board[] = "A7V8X";

WARNING: Use DEFINE_PCI_DEVICE_TABLE for struct pci_device_id
+static const struct pci_device_id uhci_pci_ids[] = { {
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.

This patch changes calls to uhci_reset_hc, uhci_check_and_reset_hc,
configure_hc, resume_detect_interrupts_are_broken and
global_suspend_mode_is_broken so that they are made through pointers
in the uhci hcd struct. This will allow these functions to be replaced
with bus/arch specific functions.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.

uhci-hub.c contained two PCI vendor checks for silicon quirks. Move
these checks into uhci-hcd.c and use bits in uhci_hcd structure to
mark that we need to use the quirks.

This patch is followed by other patches that will remove PCI
dependencies from uhci-hcd.c as well.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Though USB controller works without this most of the time, an issue was faced
where USB was configured as printer device and it was dropping first
packet(64 bytes) in full speed mode due to DATA PID mismatch.
The problem gets resolved once unused endpoints are configured as bulk.
As per P1020 RM (Table17-31, bits 19-18, bits 3-2) "When only one endpoint
(RX or TX, but not both) of an endpoint pair is used, the unused endpoint
should be configured as a bulk type endpoint." So according to the RM,
this patch is initializing TX and RX endpoints as bulk type
Signed-off-by: NSuchit Lepcha <Suchit.Lepcha@freescale.com>
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Return PTR_ERR(clk) instead of -ENOENT if clk_get fails
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the checkpatch errors ans warnings listed below:

ERROR: do not use assignment in if condition
WARNING: line over 80 characters
WARNING: braces {} are not necessary for single statement blocks
WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove a stray 'return 0' at the top of the suspend callback,
and move au1xxx_stop_ehc() out of the ehci spinlock since it takes
some time to complete.
Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.

Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.

Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.

This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current code is clearing in_lpm flag after enabling the IRQ.
If IRQ comes immediately before in_lpm flag is set, it thinks that
hardware is in low power mode and disables the IRQ.  Fix this by
clearing in_lpm flag before enabling the IRQ.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some of the simulators may cache the ep0 maxpacket size to zero
if the ep0 dQh is not setup before enabling the pullup. Hence
Setup ep0 and initialize the dQh fields once while registering the
gadget(before enabling the pullup).

HSUSB Chipidea link controller spec says ep0 is enabled always
in the HW. Hence disabling and enabling the ep0 as a part of
reset interrupt is unneccesary.
Remove the disable/enable ep0 logic from reset interrupt handling.
Signed-off-by: NAnji jonnala <anjir@codeaurora.org>
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current code queue the control OUT data request to ep0in instead of
ep0out.  Check ep0_dir and use the correct control endpoint.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The OUT endpoints are stored in 0 - hw_ep_max/2 and IN endpoints are
stored from hw_ep_max/2 - hw_ep_max in ci13xxx_ep array.  Retrieve
the IN endpoint correctly while processing endpoint feature requests.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Ask for vbus_draw regulator before registering tranceiver to disallow possible
race between registration and set_power/etc.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added several new devices to ldusb and excluded them from the HID driver.
Signed-off-by: NMichael Hund <mhund@ld-didactic.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The reset value of the uSOF cycle period is incorrect.  Set it to
60,000 bits.  Without this, several commercial USB flash memory
devices and hubs fail to work properly.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Additional PHY tuning is needed to obtain compliant 'eye' diagram
electrical characteristics.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The UCTL clock initialization will cause the ehci and ohci blocks to
become inoperable if the clocks are reinitialized.

Check to see if the clocks have already been initialized.

Also use a mutex to protect the clock initialization code so that
there can be no attempt to use the clocks before they are fully
configured.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch replaces the code that handles qtds. Intead of directly allocating
chip mem and chip slot, enqueue the transfer in a list of queue heads. Use
a centralized function enqueue_qtds() to prioritize and enqueue transfers.

This removes all of the interrupt context BUG() calls when out of chip
mem or transfer slots. It also makes it possible to efficiently use the
dual-port mem on the chip for double-buffered transfers, which improve
transfer times to/from/between usb sticks by about 40 % on my HW.

With this patch it should also be possible to handle qtd scheduling outside
of the interrupt handler, for significantly improved kernel latency. I have
not implemented this since there are some locking issues which I haven't
had time to look at.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a bug in my previous (2.6.38) patch series which caused
urb->status value to be wrong after unlink (broke usbtest 11, 12).
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since we always set the OR flag for each transfer, we can just as well set all
these bits to 1 at init and be done with it. Also, HcBufferStatus can be set
at init as per the ISP1761 datasheet page 47 with no loss of performance.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This collects urb enqueue code that was spread out all over the place
into a couple of more readable functions.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This removes the "qh is 0" printout. qh == NULL if the urb has
been unlinked, so this condition is normal.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When File Storage gadget receives SET CONFIGURATION request it tries
to cancel all pending transfers. If some request is in progress,
gadget waits for its completion. This commit allows gadget to dequeue
invalid requests in progress left after reset.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following should be done for requests after endpoint stall
condition is cleared:
1) 'in progress' request (if any) should be completed since
   Tx FIFO was flushed;
2) next request from queue (if any) should be started.

This commit does that.

Additionally set/clear stall condition code is fixed.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

UDC driver does not need to generate reply to host if request is
delivered to gadget. This is gadget's responsibility. This commit
fixes that.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit does the following:
1) clears all pending interrupts before unmasking;
2) clears interrupts as soon as possible to avoid missing
   next coming that may occur during handling;
3) removes ineffective interrupt cleaning code.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Reviewed-by: Kyoungil Kim<ki0351.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>