This fix makes it so that the fdir_perfect_lock is initialized in all
cases.  This is necessary as the fdir_filter_exit routine will always
attempt to take the lock before inspecting the filter table.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the serdes link code to support a forced mode for
some hardware, based on bit set in EEPROM.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the copyright on the igb driver files to 2011.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Register writes followed by a delay are required to have a flush
before the delay in order to commit the values to the register.  Without
the flush, the code following the delay may not function correctly.
Reported-by: NTong Ho <tong.ho@ericsson.com>
Reported-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Multiple quoted strings are concatenated without comma separators.

Make the arrays const while there.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some workloads need some headroom (NET_SKB_PAD) to avoid expensive
reallocations.

Using netdev_alloc_skb_ip_align() instead of bare skb_alloc() brings the
NET_IP_ALIGN and the NET_SKB_PAD headroom.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it. This patch covers all
remaining network drivers still containing such a check.

Cc: Joe Perches <joe@perches.com>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change references to SysKonnect in Kconfig to Marvell since
SysKonnect was acquired by Marvell back in 2002.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since new hardware chip support was added bump version.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a backport from the vendor driver of support for the newer Optima
(Prime and 2) chipsets. It also includes some setup changes for the
current Optima chip as well. The code and comments intentionally
mirror the vendor sk98lin driver to allow for easier maintenance.

Although this adds support for new chip id's, these chip id's are not
used by any of the current PCI device id's listed in the driver.
The patch is just to get initial infrastructure in place to handle them
when they come.

I don't have access to any of this hardware to actually test it yet.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is another fix picked out of the vendor driver. The IPG value
in the serial mode register is supposed to be programmed differently
at lower speeds.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found when reviewing the vendor driver. Apparently some chip versions
require receive checksumming to be enabled in order for RSS to work.

Also, if fix_features has to change some settings; put in message
in log in similar manner to netdev_fix_features.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
This would exactly mimic the behaviour of the legacy vendor driver which
also doesn't go in powersave mode if there are still TX frames that are not
transmitted.
This should make powersaving and rt2x00 a better couple.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NWim Vander Schelden <wim@fixnum.org>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently a lot of actions that can be done without the queue's tx lock
being held are done inside the locked area.
Move them out to have a leaner and meaner code that operates while the
tx lock is being held.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.

This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rt2x00 driver gets frequent occurrences of the following error message
when operating under load:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the
non-full queue 2.

This is caused by simultaneous attempts from mac80211 to send a frame via
rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame,
causing the second frame to fail sending with the above mentioned error
message.

Fix this by introducing a per-queue spinlock to serialize the TX operations
on that queue.
Reported-by: NAndreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In process and sleep allowed context, favor GFP_KERNEL allocations over
GFP_ATOMIC ones.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a dcbnl notification to the bnx2x. The notification is
sent to user mode clients following a change in the dcb negotiated
parameters as resolved by the embedded DCBX stack. 
Signed-off-by: NShmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only 128 bytes is copied, the rest of data is DMA mapped directly from
userspace.
Signed-off-by: NShirley Ma <xma@...ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch:
# improves readability of some gianfar nfc code
Signed-off-by: NSebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version number, and take "New" off the config information
since old sk98lin has been gone for a couple years.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GENESIS boards are really old PCI-X boards that are rare.
Marvell has dropped support for this hardware and there is no reason
for most users to have to have this code.

Rather than riddling code with ifdef's make one macro and let
the compiler do the dead code elimination.  This saves about 15%
of the text size.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

See also: https://bugzilla.kernel.org/show_bug.cgi?id=38862

Reported-by: jameshenderson@ruggedcom.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PCI table was using mix of defines for device id and hard coded
hex values. This patch change it to all hex values. It also adds
comments based on the names provided in the vendor driver table.

There is NO CHANGE to the actual resulting table.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net-next-2.6/drivers/net/bnx2x/bnx2x_sp.c: 19 linux/version.h not needed.
net-next-2.6/drivers/net/caif/caif_hsi.c: 9 linux/version.h not needed.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SDIO aggregation buffer size has been modified to an optimum
value which gives good throughput results.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a stray "undefined" string in the array, get rid of it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Followup to commit f82528bc (Exclude duplicated checking for
iface-up) : We no longer need percpu tx_dropped field.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a printk with a static to pr_<level>_once
Add and use DRV_DESCRIPTION to reduce string duplication.
Remove now unused version.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the rx ring is completely empty, then the device may never fire an rx
interrupt. Unfortunately, the rx interrupt is what triggers populating the
rx ring with fresh buffers, so this will cause networking to lock up.

This patch replenishes the skb in recv descriptor as soon as it is
peeled off while processing rx completions. If the skb/buffer
allocation fails, existing one is recycled and the packet in hand is
dropped. This way none of the RX desc is ever left empty, thus avoiding
starvation
Signed-off-by: NScott J. Goldman <scottjg@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a memory barrier to ensure the writes to the ring memory
are committed before the DMA ring pointer is updated.
We do a similar thing on the TX side already.
Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In routine rtl92de_hw_init(), there are two places where a failure is
not handled correctly.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a number of loops to implement delays. These are replaced with
single calls to mdelay().

The need for a fix was noted by Andrew Morton <akpm@linux-foundation.org>.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tests of a boolean against "true" are not needed as non-zero is sufficient..
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This should be unnecessary if synchronize_irq is used.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>