提交 cc020ea4 编写于 作者: V Valentin Rothberg 提交者: Greg Kroah-Hartman

drivers/tty/serial/crisv10.c: remove dead #ifdef blocks

ETRAX_RS485_{ON_PORT_G, LTC1387} are not defined in Kconfig.  The
affected #ifdef block have not been compiled for years, so remove them
entirely.
Signed-off-by: NValentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 5a56abc7
......@@ -56,10 +56,6 @@ static char *serial_version = "$Revision: 1.25 $";
#error "RX_TIMEOUT_TICKS == 0 not allowed, use 1"
#endif
#if defined(CONFIG_ETRAX_RS485_ON_PA) && defined(CONFIG_ETRAX_RS485_ON_PORT_G)
#error "Disable either CONFIG_ETRAX_RS485_ON_PA or CONFIG_ETRAX_RS485_ON_PORT_G"
#endif
/*
* All of the compatibilty code so we can compile serial.c against
* older kernels is hidden in serial_compat.h
......@@ -487,9 +483,6 @@ static struct fast_timer fast_timers_rs485[NR_PORTS];
#if defined(CONFIG_ETRAX_RS485_ON_PA)
static int rs485_pa_bit = CONFIG_ETRAX_RS485_ON_PA_BIT;
#endif
#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
static int rs485_port_g_bit = CONFIG_ETRAX_RS485_ON_PORT_G_BIT;
#endif
#endif
/* Info and macros needed for each ports extra control/status signals. */
......@@ -1367,16 +1360,6 @@ e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
#if defined(CONFIG_ETRAX_RS485_ON_PA)
*R_PORT_PA_DATA = port_pa_data_shadow |= (1 << rs485_pa_bit);
#endif
#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
rs485_port_g_bit, 1);
#endif
#if defined(CONFIG_ETRAX_RS485_LTC1387)
REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 1);
REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1);
#endif
info->rs485 = *r;
......@@ -3707,16 +3690,6 @@ rs_close(struct tty_struct *tty, struct file * filp)
info->rs485.flags &= ~(SER_RS485_ENABLED);
#if defined(CONFIG_ETRAX_RS485_ON_PA)
*R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit);
#endif
#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
rs485_port_g_bit, 0);
#endif
#if defined(CONFIG_ETRAX_RS485_LTC1387)
REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 0);
REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 0);
#endif
}
#endif
......@@ -4246,15 +4219,6 @@ static int __init rs_init(void)
return -EBUSY;
}
#endif
#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit,
rs485_port_g_bit)) {
printk(KERN_ERR "ETRAX100LX serial: Could not allocate "
"RS485 pin\n");
put_tty_driver(driver);
return -EBUSY;
}
#endif
#endif
/* Initialize the tty_driver structure */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册