ARM: ux500: move GPIO217/218 config to device tree

This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

arch/arm/boot/dts/ste-href-tvk1281618.dtsi

@@ -22,6 +22,8 @@
 				reg = <0x44>;
 				interrupt-parent = <&gpio6>;
 				interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tc35893_tvk_mode>;
 
 				interrupt-controller;
 				#interrupt-cells = <1>;
@@ -64,5 +66,16 @@
 				};
 			};
 		};
+		pinctrl {
+			/* Pull up this GPIO pin */
+			tc35893 {
+				tc35893_tvk_mode: tc35893_tvk {
+					tvk_cfg {
+						ste,pins = "GPIO218_AH11";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+		};
 	};
 };

arch/arm/boot/dts/ste-hrefprev60.dtsi

@@ -33,6 +33,8 @@
 				reg = <0x42>;
 				interrupt-parent = <&gpio6>;
 				interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tc35892_hrefprev60_mode>;
 
 				interrupt-controller;
 				#interrupt-cells = <1>;
@@ -71,6 +73,14 @@
 
 				};
 			};
+			tc35892 {
+				tc35892_hrefprev60_mode: tc35892_hrefprev60 {
+					hrefprev60_cfg {
+						ste,pins = "GPIO217_AH12";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi

@@ -31,6 +31,11 @@
 		ste,output = <OUTPUT_LOW>;
 	};
 
+	gpio_in_pu: gpio_input_pull_up {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,input = <INPUT_PULLUP>;
+	};
+
 	gpio_out_lo: gpio_output_low {
 		ste,gpio = <GPIOMODE_ENABLED>;
 		ste,output = <OUTPUT_LOW>;

arch/arm/mach-ux500/board-mop500-pins.c

@@ -340,11 +340,6 @@ static struct pinctrl_map __initdata mop500_family_pinmap[] = {
 	DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
 	DB8500_PIN_HOG("GPIO68_E1", in_pu),
 	DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
-	/*
-	 * STMPE1601/tc35893 keypad IRQ GPIO 218
-	 * TODO: set for snowball and HREF really??
-	 */
-	DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
 	/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
 	DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
 	DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
@@ -625,8 +620,6 @@ static struct pinctrl_map __initdata mop500_pinmap[] = {
 	DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
 	DB8500_PIN_HOG("GPIO6_AF6", in_pu),
 	DB8500_PIN_HOG("GPIO7_AG5", in_pu),
-	/* TC35892 IRQ, pull up the line, let the driver mux in the pin */
-	DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
 	/*
 	 * Runtime stuff: make it possible to mux in the SKE keypad
 	 * and bias the pins