Kconfig 9.0 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3
config M32R
	bool
	default y
S
Sam Ravnborg 已提交
4
	select HAVE_IDE
M
Mathieu Desnoyers 已提交
5
	select HAVE_OPROFILE
6
	select INIT_ALL_POSSIBLE
7 8 9
	select HAVE_KERNEL_GZIP
	select HAVE_KERNEL_BZIP2
	select HAVE_KERNEL_LZMA
10
	select ARCH_WANT_IPC_PARSE_VERSION
11
	select HAVE_DEBUG_BUGVERBOSE
12
	select VIRT_TO_BUS
13
	select GENERIC_IRQ_PROBE
14
	select GENERIC_IRQ_SHOW
S
Steven Rostedt 已提交
15
	select GENERIC_ATOMIC64
16
	select ARCH_HAS_DEVMEM_IS_ALLOWED
17
	select ARCH_USES_GETTIMEOFFSET
18
	select MODULES_USE_ELF_RELA
19
	select HAVE_DEBUG_STACKOVERFLOW
20
	select CPU_NO_EFFICIENT_FFS
L
Linus Torvalds 已提交
21 22 23 24 25 26 27 28

config SBUS
	bool

config GENERIC_ISA_DMA
	bool
	default y

29 30 31 32
config ZONE_DMA
	bool
	default y

33
config NO_IOPORT_MAP
A
Al Viro 已提交
34 35
	def_bool y

36 37 38
config NO_DMA
	def_bool y

39 40 41 42
config HZ
	int
	default 100

L
Linus Torvalds 已提交
43 44
source "init/Kconfig"

45 46
source "kernel/Kconfig.freezer"

L
Linus Torvalds 已提交
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

menu "Processor type and features"

choice
	prompt "Platform Type"
	default PLAT_MAPPI

config PLAT_MAPPI
	bool "Mappi-I"
	help
	  The Mappi-I is an FPGA board for SOC (System-On-a-Chip) prototyping.
	  You can operate a Linux system on this board by using an M32R
	  softmacro core, which is a fully-synthesizable functional model
	  described in Verilog-HDL.

	  The Mappi-I board was the first platform, which had been used
	  to port and develop a Linux system for the M32R processor.
	  Currently, the Mappi-II, an heir to the Mappi-I, is available.

config PLAT_USRV
	bool "uServer"
68
	select PLAT_HAS_INT1ICU
L
Linus Torvalds 已提交
69 70 71

config PLAT_M32700UT
	bool "M32700UT"
72 73 74
	select PLAT_HAS_INT0ICU
	select PLAT_HAS_INT1ICU
	select PLAT_HAS_INT2ICU
L
Linus Torvalds 已提交
75 76 77 78 79 80 81 82
	help
	  The M3T-M32700UT is an evaluation board based on uT-Engine
	  specification.  This board has an M32700 (Chaos) evaluation chip.
	  You can say Y for SMP, because the M32700 is a single chip
	  multiprocessor.

config PLAT_OPSPUT
	bool "OPSPUT"
83 84 85
	select PLAT_HAS_INT0ICU
	select PLAT_HAS_INT1ICU
	select PLAT_HAS_INT2ICU
L
Linus Torvalds 已提交
86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101
	help
	  The OPSPUT is an evaluation board based on uT-Engine
	  specification.  This board has a OPSP-REP chip.

config PLAT_OAKS32R
	bool "OAKS32R"
	help
	  The OAKS32R is a tiny, inexpensive evaluation board.
	  Please note that if you say Y here and choose chip "M32102",
	  say N for MMU and select a no-MMU version kernel, otherwise
	  a kernel with MMU support will not work, because the M32102
	  is a microcontroller for embedded systems and it has no MMU.

config PLAT_MAPPI2
       bool "Mappi-II(M3A-ZA36/M3A-ZA52)"

102 103 104
config PLAT_MAPPI3
       bool "Mappi-III(M3A-2170)"

105 106
config PLAT_M32104UT
	bool "M32104UT"
107
	select PLAT_HAS_INT1ICU
108 109 110 111
	help
	  The M3T-M32104UT is an reference board based on uT-Engine
	  specification.  This board has a M32104 chip.

L
Linus Torvalds 已提交
112 113 114 115 116 117 118 119 120 121 122 123
endchoice

choice
	prompt "Processor family"
	default CHIP_M32700

config CHIP_M32700
	bool "M32700 (Chaos)"

config CHIP_M32102
	bool "M32102"

124 125 126 127
config CHIP_M32104
	bool "M32104"
	depends on PLAT_M32104UT

L
Linus Torvalds 已提交
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149
config CHIP_VDEC2
       bool "VDEC2"

config CHIP_OPSP
       bool "OPSP"

endchoice

config MMU
	bool "Support for memory management hardware"
	depends on CHIP_M32700 || CHIP_VDEC2 || CHIP_OPSP
	default y

config TLB_ENTRIES
       int "TLB Entries"
       depends on CHIP_M32700 || CHIP_VDEC2 || CHIP_OPSP
       default 32 if CHIP_M32700 || CHIP_OPSP
       default 16 if CHIP_VDEC2


config ISA_M32R
        bool
150
	depends on CHIP_M32102 || CHIP_M32104
L
Linus Torvalds 已提交
151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167
	default y

config ISA_M32R2
	bool
	depends on CHIP_M32700 || CHIP_VDEC2 || CHIP_OPSP
	default y

config ISA_DSP_LEVEL2
	bool
	depends on CHIP_M32700 || CHIP_OPSP
	default y

config ISA_DUAL_ISSUE
	bool
	depends on CHIP_M32700 || CHIP_OPSP
	default y

168 169 170 171 172 173 174 175 176 177 178 179
config PLAT_HAS_INT0ICU
	bool
	default n

config PLAT_HAS_INT1ICU
	bool
	default n

config PLAT_HAS_INT2ICU
	bool
	default n

L
Linus Torvalds 已提交
180 181 182 183
config BUS_CLOCK
	int "Bus Clock [Hz] (integer)"
	default "70000000" if PLAT_MAPPI
	default "25000000" if PLAT_USRV
184
	default "50000000" if PLAT_MAPPI3
L
Linus Torvalds 已提交
185 186
	default "50000000" if PLAT_M32700UT
	default "50000000" if PLAT_OPSPUT
187
	default "54000000" if PLAT_M32104UT
L
Linus Torvalds 已提交
188 189 190 191 192 193 194 195 196 197 198 199 200
	default "33333333" if PLAT_OAKS32R
	default "20000000" if PLAT_MAPPI2

config TIMER_DIVIDE
	int "Timer divider (integer)"
	default "128"

config CPU_LITTLE_ENDIAN
        bool "Generate little endian code"
	default n

config MEMORY_START
	hex "Physical memory start address (hex)"
201
	default "08000000" if PLAT_MAPPI || PLAT_MAPPI2 || PLAT_MAPPI3
L
Linus Torvalds 已提交
202 203 204
	default "08000000" if PLAT_USRV
	default "08000000" if PLAT_M32700UT
	default "08000000" if PLAT_OPSPUT
205
	default "04000000" if PLAT_M32104UT
L
Linus Torvalds 已提交
206 207 208 209
	default "01000000" if PLAT_OAKS32R

config MEMORY_SIZE
	hex "Physical memory size (hex)"
210
	default "08000000" if PLAT_MAPPI3
L
Linus Torvalds 已提交
211 212 213 214
	default "04000000" if PLAT_MAPPI || PLAT_MAPPI2
	default "02000000" if PLAT_USRV
	default "01000000" if PLAT_M32700UT
	default "01000000" if PLAT_OPSPUT
215
	default "01000000" if PLAT_M32104UT
L
Linus Torvalds 已提交
216 217
	default "00800000" if PLAT_OAKS32R

218
config ARCH_DISCONTIGMEM_ENABLE
L
Linus Torvalds 已提交
219
	bool "Internal RAM Support"
220
	depends on CHIP_M32700 || CHIP_M32102 || CHIP_VDEC2 || CHIP_OPSP || CHIP_M32104
L
Linus Torvalds 已提交
221 222
	default y

223 224
source "mm/Kconfig"

L
Linus Torvalds 已提交
225 226
config IRAM_START
	hex "Internal memory start address (hex)"
227 228 229
	default "00f00000" if !CHIP_M32104
	default "00700000" if CHIP_M32104
	depends on (CHIP_M32700 || CHIP_M32102 || CHIP_VDEC2 || CHIP_OPSP || CHIP_M32104) && DISCONTIGMEM
L
Linus Torvalds 已提交
230 231 232

config IRAM_SIZE
	hex "Internal memory size (hex)"
233
	depends on (CHIP_M32700 || CHIP_M32102 || CHIP_VDEC2 || CHIP_OPSP || CHIP_M32104) && DISCONTIGMEM
L
Linus Torvalds 已提交
234
	default "00080000" if CHIP_M32700
235
	default "00010000" if CHIP_M32102 || CHIP_OPSP || CHIP_M32104
L
Linus Torvalds 已提交
236 237 238 239 240 241
	default "00008000" if CHIP_VDEC2

#
# Define implied options from the CPU selection here
#

N
Nick Piggin 已提交
242 243 244 245 246
config GENERIC_LOCKBREAK
	bool
	default y
	depends on SMP && PREEMPT

L
Linus Torvalds 已提交
247 248 249 250 251 252 253 254 255
config RWSEM_GENERIC_SPINLOCK
	bool
	depends on M32R
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool
	default n

256 257 258 259 260 261 262 263
config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

264 265 266 267
config GENERIC_HWEIGHT
	bool
	default y

L
Linus Torvalds 已提交
268 269 270 271
config GENERIC_CALIBRATE_DELAY
	bool
	default y

272
config SCHED_OMIT_FRAME_POINTER
273 274 275
        bool
        default y

276
source "kernel/Kconfig.preempt"
L
Linus Torvalds 已提交
277 278 279

config SMP
	bool "Symmetric multi-processing support"
280
	depends on MMU
L
Linus Torvalds 已提交
281 282
	---help---
	  This enables support for systems with more than one CPU. If you have
283 284
	  a system with only one CPU, say N. If you have a system with more
	  than one CPU, say Y.
L
Linus Torvalds 已提交
285

286
	  If you say N here, the kernel will run on uni- and multiprocessor
L
Linus Torvalds 已提交
287 288
	  machines, but will use only one CPU of a multiprocessor machine. If
	  you say Y here, the kernel will run on many, but not all,
289
	  uniprocessor machines. On a uniprocessor machine, the kernel
L
Linus Torvalds 已提交
290 291 292 293 294 295
	  will run faster if you say N here.

	  People using multiprocessor machines who say Y here should also say
	  Y to "Enhanced Real Time Clock Support", below. The "Advanced Power
	  Management" code will be disabled if you say Y here.

A
Adrian Bunk 已提交
296
	  See also the SMP-HOWTO available at
297
	  <http://tldp.org/HOWTO/SMP-HOWTO.html>.
L
Linus Torvalds 已提交
298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321

	  If you don't know what to do here, say N.

config CHIP_M32700_TS1
	bool "Workaround code for the M32700 TS1 chip's bug"
	depends on (CHIP_M32700 && SMP)
	default n

config NR_CPUS
	int "Maximum number of CPUs (2-32)"
	range 2 32
	depends on SMP
	default "2"
	help
	  This allows you to specify the maximum number of CPUs which this
	  kernel will support.  The maximum supported value is 32 and the
	  minimum value which makes sense is 2.

	  This is purely to save memory - each supported CPU adds
	  approximately eight kilobytes to the kernel image.

# Common NUMA Features
config NUMA
	bool "Numa Memory Allocation Support"
A
Al Viro 已提交
322
	depends on SMP && BROKEN
L
Linus Torvalds 已提交
323 324
	default n

Y
Yasunori Goto 已提交
325 326 327 328 329
config NODES_SHIFT
	int
	default "1"
	depends on NEED_MULTIPLE_NODES

L
Linus Torvalds 已提交
330 331 332 333 334 335 336
endmenu


menu "Bus options (PCI, PCMCIA, EISA, MCA, ISA)"

config PCI
	bool "PCI support"
A
Al Viro 已提交
337
	depends on BROKEN
L
Linus Torvalds 已提交
338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386
	default n
	help
	  Find out whether you have a PCI motherboard. PCI is the name of a
	  bus system, i.e. the way the CPU talks to the other stuff inside
	  your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
	  VESA. If you have PCI, say Y, otherwise N.

choice
	prompt "PCI access mode"
	depends on PCI
	default PCI_GOANY

config PCI_GOBIOS
	bool "BIOS"
	---help---
	  On PCI systems, the BIOS can be used to detect the PCI devices and
	  determine their configuration. However, some old PCI motherboards
	  have BIOS bugs and may crash if this is done. Also, some embedded
	  PCI-based systems don't have any BIOS at all. Linux can also try to
	  detect the PCI hardware directly without using the BIOS.

	  With this option, you can specify how Linux should detect the PCI
	  devices. If you choose "BIOS", the BIOS will be used, if you choose
	  "Direct", the BIOS won't be used, and if you choose "Any", the
	  kernel will try the direct access method and falls back to the BIOS
	  if that doesn't work. If unsure, go with the default, which is
	  "Any".

config PCI_GODIRECT
	bool "Direct"

config PCI_GOANY
	bool "Any"

endchoice

config PCI_BIOS
	bool
	depends on PCI && (PCI_GOBIOS || PCI_GOANY)
	default y

config PCI_DIRECT
	bool
 	depends on PCI && (PCI_GODIRECT || PCI_GOANY)
	default y

source "drivers/pci/Kconfig"

config ISA
A
Adrian Bunk 已提交
387
	bool
L
Linus Torvalds 已提交
388 389 390 391 392 393 394 395 396 397 398 399

source "drivers/pcmcia/Kconfig"

endmenu


menu "Executable file formats"

source "fs/Kconfig.binfmt"

endmenu

400 401
source "net/Kconfig"

L
Linus Torvalds 已提交
402 403 404 405 406 407 408 409 410 411 412
source "drivers/Kconfig"

source "fs/Kconfig"

source "arch/m32r/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

source "lib/Kconfig"