Kconfig 18.7 KB
Newer Older
1 2 3 4 5 6 7
config LEDS_GPIO_REGISTER
	bool
	help
	  This option provides the function gpio_led_register_device.
	  As this function is used by arch code it must not be compiled as a
	  module.

8
menuconfig NEW_LEDS
R
Richard Purdie 已提交
9 10
	bool "LED Support"
	help
11 12 13
	  Say Y to enable Linux LED support.  This allows control of supported
	  LEDs from both userspace and optionally, by kernel events (triggers).

14 15
if NEW_LEDS

R
Richard Purdie 已提交
16
config LEDS_CLASS
17
	tristate "LED Class Support"
R
Richard Purdie 已提交
18 19 20 21
	help
	  This option enables the led sysfs class in /sys/class/leds.  You'll
	  need this to do anything useful with LEDs.  If unsure, say N.

22 23 24 25 26 27 28 29 30 31
config LEDS_CLASS_FLASH
	tristate "LED Flash Class Support"
	depends on LEDS_CLASS
	help
	  This option enables the flash led sysfs class in /sys/class/leds.
	  It wrapps LED Class and adds flash LEDs specific sysfs attributes
	  and kernel internal API to it. You'll need this to provide support
	  for the flash related features of a LED device. It can be built
	  as a module.

B
Ben Dooks 已提交
32
comment "LED drivers"
33

H
Haojian Zhuang 已提交
34 35
config LEDS_88PM860X
	tristate "LED Support for Marvell 88PM860x PMIC"
J
Johannes Berg 已提交
36
	depends on LEDS_CLASS
R
Richard Purdie 已提交
37
	depends on MFD_88PM860X
H
Haojian Zhuang 已提交
38 39 40 41
	help
	  This option enables support for on-chip LED drivers found on Marvell
	  Semiconductor 88PM8606 PMIC.

42 43 44
config LEDS_AAT1290
	tristate "LED support for the AAT1290"
	depends on LEDS_CLASS_FLASH
R
Randy Dunlap 已提交
45
	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
46
	depends on GPIOLIB || COMPILE_TEST
47
	depends on OF
48
	depends on PINCTRL
49 50 51
	help
	 This option enables support for the LEDs on the AAT1290.

52 53 54
config LEDS_BCM6328
	tristate "LED Support for Broadcom BCM6328"
	depends on LEDS_CLASS
55
	depends on HAS_IOMEM
56 57 58 59 60
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6328
	  LED HW controller accessed via MMIO registers.

61 62 63
config LEDS_BCM6358
	tristate "LED Support for Broadcom BCM6358"
	depends on LEDS_CLASS
64
	depends on HAS_IOMEM
65 66 67 68 69
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6358
	  LED HW controller accessed via MMIO registers.

70 71 72 73 74 75 76 77 78 79
config LEDS_LM3530
	tristate "LCD Backlight driver for LM3530"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the LCD backlight using
	  LM3530 ambient light sensor chip. This ALS chip can be
	  controlled manually or using PWM input or using ambient
	  light automatically.

J
Johan Hovold 已提交
80 81 82 83 84 85 86 87 88 89 90 91 92
config LEDS_LM3533
	tristate "LED support for LM3533"
	depends on LEDS_CLASS
	depends on MFD_LM3533
	help
	  This option enables support for the LEDs on National Semiconductor /
	  TI LM3533 Lighting Power chips.

	  The LEDs can be controlled directly, through PWM input, or by the
	  ambient-light-sensor interface. The chip supports
	  hardware-accelerated blinking with maximum on and off periods of 9.8
	  and 77 seconds respectively.

93 94 95 96 97 98 99 100 101 102 103
config LEDS_LM3642
	tristate "LED support for LM3642 Chip"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to LM3642.
	  The LM3642 is a 4MHz fixed-frequency synchronous boost
	  converter plus 1.5A constant current driver for a high-current
	  white LED.


104 105
config LEDS_LOCOMO
	tristate "LED Support for Locomo device"
J
Johannes Berg 已提交
106
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
107
	depends on SHARP_LOCOMO
108 109 110 111
	help
	  This option enables support for the LEDs on Sharp Locomo.
	  Zaurus models SL-5500 and SL-5600.

112 113
config LEDS_MIKROTIK_RB532
	tristate "LED Support for Mikrotik Routerboard 532"
J
Johannes Berg 已提交
114
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
115
	depends on MIKROTIK_RB532
116 117 118 119
	help
	  This option enables support for the so called "User LED" of
	  Mikrotik's Routerboard 532.

B
Ben Dooks 已提交
120 121
config LEDS_S3C24XX
	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
J
Johannes Berg 已提交
122
	depends on LEDS_CLASS
123
	depends on ARCH_S3C24XX
B
Ben Dooks 已提交
124 125 126 127
	help
	  This option enables support for LEDs connected to GPIO lines
	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.

128 129
config LEDS_NET48XX
	tristate "LED Support for Soekris net48xx series Error LED"
J
Johannes Berg 已提交
130
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
131
	depends on SCx200_GPIO
132 133 134 135
	help
	  This option enables support for the Soekris net4801 and net4826 error
	  LED.

136 137
config LEDS_FSG
	tristate "LED Support for the Freecom FSG-3"
J
Johannes Berg 已提交
138
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
139
	depends on MACH_FSG
140 141 142
	help
	  This option enables support for the LEDs on the Freecom FSG-3.

143 144
config LEDS_WRAP
	tristate "LED Support for the WRAP series LEDs"
J
Johannes Berg 已提交
145
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
146
	depends on SCx200_GPIO
147 148 149
	help
	  This option enables support for the PCEngines WRAP programmable LEDs.

Y
Yoichi Yuasa 已提交
150 151
config LEDS_COBALT_QUBE
	tristate "LED Support for the Cobalt Qube series front LED"
J
Johannes Berg 已提交
152
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
153
	depends on MIPS_COBALT
154
	help
Y
Yoichi Yuasa 已提交
155
	  This option enables support for the front LED on Cobalt Qube series
156

157 158
config LEDS_COBALT_RAQ
	bool "LED Support for the Cobalt Raq series"
159
	depends on LEDS_CLASS=y && MIPS_COBALT
160 161 162 163
	select LEDS_TRIGGERS
	help
	  This option enables support for the Cobalt Raq series LEDs.

164 165
config LEDS_SUNFIRE
	tristate "LED support for SunFire servers."
J
Johannes Berg 已提交
166
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
167
	depends on SPARC64
168 169 170 171 172
	select LEDS_TRIGGERS
	help
	  This option enables support for the Left, Middle, and Right
	  LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.

173 174
config LEDS_IPAQ_MICRO
	tristate "LED Support for the Compaq iPAQ h3xxx"
175
	depends on LEDS_CLASS
176 177 178 179 180
	depends on MFD_IPAQ_MICRO
	help
	  Choose this option if you want to use the notification LED on
	  Compaq/HP iPAQ h3100 and h3600.

181 182
config LEDS_HP6XX
	tristate "LED Support for the HP Jornada 6xx"
J
Johannes Berg 已提交
183
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
184
	depends on SH_HP6XX
185
	help
186
	  This option enables LED support for the handheld
187 188
	  HP Jornada 620/660/680/690.

R
Riku Voipio 已提交
189 190
config LEDS_PCA9532
	tristate "LED driver for PCA9532 dimmer"
J
Johannes Berg 已提交
191
	depends on LEDS_CLASS
192
	depends on I2C && INPUT
R
Riku Voipio 已提交
193 194
	help
	  This option enables support for NXP pca9532
195
	  LED controller. It is generally only useful
R
Riku Voipio 已提交
196 197
	  as a platform driver

198 199 200 201 202 203 204 205 206 207
config LEDS_PCA9532_GPIO
	bool "Enable GPIO support for PCA9532"
	depends on LEDS_PCA9532
	depends on GPIOLIB
	help
	  Allow unused pins on PCA9532 to be used as gpio.

	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
	  set to PCA9532_TYPE_GPIO.

208 209
config LEDS_GPIO
	tristate "LED Support for GPIO connected LEDs"
J
Johannes Berg 已提交
210
	depends on LEDS_CLASS
211
	depends on GPIOLIB || COMPILE_TEST
212 213 214
	help
	  This option enables support for the LEDs connected to GPIO
	  outputs. To be useful the particular board must have LEDs
215 216 217 218
	  and they must be connected to the GPIO lines.  The LEDs must be
	  defined as platform devices and/or OpenFirmware platform devices.
	  The code to use these bindings can be selected below.

219 220
config LEDS_LP3944
	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
J
Johannes Berg 已提交
221
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
222
	depends on I2C
223
	help
224 225 226
	  This option enables support for LEDs connected to the National
	  Semiconductor LP3944 Lighting Management Unit (LMU) also known as
	  Fun Light Chip.
227 228 229 230

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp3944.

231
config LEDS_LP55XX_COMMON
232 233
	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
	depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
234
	select FW_LOADER
235
	select FW_LOADER_USER_HELPER
236
	help
237
	  This option supports common operations for LP5521/5523/55231/5562/8501
238 239
	  devices.

240 241 242
config LEDS_LP5521
	tristate "LED Support for N.S. LP5521 LED driver chip"
	depends on LEDS_CLASS && I2C
243
	select LEDS_LP55XX_COMMON
244 245 246 247 248 249 250
	help
	  If you say yes here you get support for the National Semiconductor
	  LP5521 LED driver. It is 3 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

config LEDS_LP5523
251
	tristate "LED Support for TI/National LP5523/55231 LED driver chip"
252
	depends on LEDS_CLASS && I2C
253
	select LEDS_LP55XX_COMMON
254
	help
255 256 257
	  If you say yes here you get support for TI/National Semiconductor
	  LP5523/55231 LED driver.
	  It is 9 channel chip with programmable engines.
258 259 260
	  Driver provides direct control via LED class and interface for
	  programming the engines.

K
Kim, Milo 已提交
261 262 263 264 265 266 267 268 269 270
config LEDS_LP5562
	tristate "LED Support for TI LP5562 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP5562 LED driver.
	  It is 4 channels chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

271 272 273 274 275 276 277 278 279 280 281 282
config LEDS_LP8501
	tristate "LED Support for TI LP8501 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP8501 LED driver.
	  It is 9 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.
	  It is similar as LP5523, but output power selection is available.
	  And register layout and engine program schemes are different.

K
Kim, Milo 已提交
283 284 285 286 287 288 289
config LEDS_LP8788
	tristate "LED support for the TI LP8788 PMIC"
	depends on LEDS_CLASS
	depends on MFD_LP8788
	help
	  This option enables support for the Keyboard LEDs on the LP8788 PMIC.

290 291
config LEDS_LP8860
	tristate "LED support for the TI LP8860 4 channel LED driver"
A
Axel Lin 已提交
292 293
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
294 295 296 297 298 299 300
	help
	  If you say yes here you get support for the TI LP8860 4 channel
	  LED driver.
	  This option enables support for the display cluster LEDs
	  on the LP8860 4 channel LED driver using the I2C communication
	  bus.

301
config LEDS_CLEVO_MAIL
302
	tristate "Mail LED on Clevo notebook"
J
Johannes Berg 已提交
303
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
304
	depends on X86 && SERIO_I8042 && DMI
305 306 307 308 309
	help
	  This driver makes the mail LED accessible from userspace
	  programs through the leds subsystem. This LED have three
	  known mode: off, blink at 0.5Hz and blink at 1Hz.

310 311 312 313 314
	  The driver supports two kinds of interface: using ledtrig-timer
	  or through /sys/class/leds/clevo::mail/brightness. As this LED
	  cannot change it's brightness it blinks instead. The brightness
	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
	  blink at 1Hz.
315 316 317

	  This module can drive the mail LED for the following notebooks:

318
	  	Clevo D400P
319 320 321 322 323 324 325
	  	Clevo D410J
	  	Clevo D410V
	  	Clevo D400V/D470V (not tested, but might work)
	  	Clevo M540N
	  	Clevo M5x0N (not tested, but might work)
	  	Positivo Mobile (Clevo M5x0V)

326
	  If your model is not listed here you can try the "nodetect"
327
	  module parameter.
328

329 330 331
	  To compile this driver as a module, choose M here: the
	  module will be called leds-clevo-mail.

332 333
config LEDS_PCA955X
	tristate "LED Support for PCA955x I2C chips"
J
Johannes Berg 已提交
334
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
335
	depends on I2C
336 337 338 339 340
	help
	  This option enables support for LEDs connected to PCA955x
	  LED driver chips accessed via the I2C bus.  Supported
	  devices include PCA9550, PCA9551, PCA9552, and PCA9553.

341
config LEDS_PCA963X
342
	tristate "LED support for PCA963x I2C chip"
343 344 345
	depends on LEDS_CLASS
	depends on I2C
	help
346 347 348
	  This option enables support for LEDs connected to the PCA963x
	  LED driver chip accessed via the I2C bus. Supported
	  devices include PCA9633 and PCA9634
349

M
Mark Brown 已提交
350 351
config LEDS_WM831X_STATUS
	tristate "LED support for status LEDs on WM831x PMICs"
J
Johannes Berg 已提交
352
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
353
	depends on MFD_WM831X
M
Mark Brown 已提交
354 355 356 357
	help
	  This option enables support for the status LEDs of the WM831x
          series of PMICs.

M
Mark Brown 已提交
358 359
config LEDS_WM8350
	tristate "LED Support for WM8350 AudioPlus PMIC"
J
Johannes Berg 已提交
360
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
361
	depends on MFD_WM8350
M
Mark Brown 已提交
362 363 364 365
	help
	  This option enables support for LEDs driven by the Wolfson
	  Microelectronics WM8350 AudioPlus PMIC.

366 367
config LEDS_DA903X
	tristate "LED Support for DA9030/DA9034 PMIC"
J
Johannes Berg 已提交
368
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
369
	depends on PMIC_DA903X
370 371 372 373
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9030/DA9034 PMICs.

374 375 376 377 378 379 380 381
config LEDS_DA9052
	tristate "Dialog DA9052/DA9053 LEDS"
	depends on LEDS_CLASS
	depends on PMIC_DA9052
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.

382 383
config LEDS_DAC124S085
	tristate "LED Support for DAC124S085 SPI DAC"
J
Johannes Berg 已提交
384
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
385
	depends on SPI
386 387 388 389
	help
	  This option enables support for DAC124S085 SPI DAC from NatSemi,
	  which can be used to control up to four LEDs.

390 391
config LEDS_PWM
	tristate "PWM driven LED Support"
J
Johannes Berg 已提交
392
	depends on LEDS_CLASS
393
	depends on PWM
394 395 396
	help
	  This option enables support for pwm driven LEDs

397 398
config LEDS_REGULATOR
	tristate "REGULATOR driven LED support"
J
Johannes Berg 已提交
399
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
400
	depends on REGULATOR
401 402 403
	help
	  This option enables support for regulator driven LEDs.

K
Kim Kyuwon 已提交
404 405
config LEDS_BD2802
	tristate "LED driver for BD2802 RGB LED"
J
Johannes Berg 已提交
406
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
407
	depends on I2C
K
Kim Kyuwon 已提交
408 409 410 411
	help
	  This option enables support for BD2802GU RGB LED driver chips
	  accessed via the I2C bus.

412 413
config LEDS_INTEL_SS4200
	tristate "LED driver for Intel NAS SS4200 series"
J
Johannes Berg 已提交
414
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
415
	depends on PCI && DMI
416 417 418 419 420 421
	help
	  This option enables support for the Intel SS4200 series of
	  Network Attached Storage servers.  You may control the hard
	  drive or power LEDs on the front panel.  Using this driver
	  can stop the front LED from blinking after startup.

422 423
config LEDS_LT3593
	tristate "LED driver for LT3593 controllers"
J
Johannes Berg 已提交
424
	depends on LEDS_CLASS
425
	depends on GPIOLIB || COMPILE_TEST
426 427 428 429 430
	help
	  This option enables support for LEDs driven by a Linear Technology
	  LT3593 controller. This controller uses a special one-wire pulse
	  coding protocol to set the brightness.

431 432
config LEDS_ADP5520
	tristate "LED Support for ADP5520/ADP5501 PMIC"
J
Johannes Berg 已提交
433
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
434
	depends on PMIC_ADP5520
435 436 437 438 439 440 441
	help
	  This option enables support for on-chip LED drivers found
	  on Analog Devices ADP5520/ADP5501 PMICs.

	  To compile this driver as a module, choose M here: the module will
	  be called leds-adp5520.

442 443
config LEDS_DELL_NETBOOKS
	tristate "External LED on Dell Business Netbooks"
J
Johannes Berg 已提交
444
	depends on LEDS_CLASS
445
	depends on X86 && ACPI_WMI
446
	depends on DELL_SMBIOS
447 448 449 450
	help
	  This adds support for the Latitude 2100 and similar
	  notebooks that have an external LED.

451
config LEDS_MC13783
452
	tristate "LED Support for MC13XXX PMIC"
J
Johannes Berg 已提交
453
	depends on LEDS_CLASS
454
	depends on MFD_MC13XXX
455 456
	help
	  This option enable support for on-chip LED drivers found
457
	  on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
458

459 460
config LEDS_NS2
	tristate "LED support for Network Space v2 GPIO LEDs"
J
Johannes Berg 已提交
461
	depends on LEDS_CLASS
462
	depends on MACH_KIRKWOOD || MACH_ARMADA_370
463 464
	default y
	help
465 466 467 468 469 470 471
	  This option enables support for the dual-GPIO LEDs found on the
	  following LaCie/Seagate boards:

		Network Space v2 (and parents: Max, Mini)
		Internet Space v2
		d2 Network v2
		n090401 (Seagate NAS 4-Bay)
472

473 474
config LEDS_NETXBIG
	tristate "LED support for Big Network series LEDs"
475
	depends on LEDS_CLASS
476
	depends on MACH_KIRKWOOD
477 478 479 480 481 482
	default y
	help
	  This option enable support for LEDs found on the LaCie 2Big
	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
	  controlled through a GPIO extension bus.

P
Paul Parsons 已提交
483 484
config LEDS_ASIC3
	bool "LED support for the HTC ASIC3"
485
	depends on LEDS_CLASS=y
P
Paul Parsons 已提交
486 487 488 489 490 491 492 493
	depends on MFD_ASIC3
	default y
	help
	  This option enables support for the LEDs on the HTC ASIC3. The HTC
	  ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
	  cannot be used. This driver supports hardware blinking with an on+off
	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.

494 495 496 497 498 499 500 501
config LEDS_TCA6507
	tristate "LED Support for TCA6507 I2C chip"
	depends on LEDS_CLASS && I2C
	help
	  This option enables support for LEDs connected to TC6507
	  LED driver chips accessed via the I2C bus.
	  Driver support brightness control and hardware-assisted blinking.

502 503 504 505 506 507 508 509
config LEDS_TLC591XX
	tristate "LED driver for TLC59108 and TLC59116 controllers"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for Texas Instruments TLC59108
	  and TLC59116 LED controllers.

510 511 512
config LEDS_MAX77693
	tristate "LED support for MAX77693 Flash"
	depends on LEDS_CLASS_FLASH
513
	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
514 515 516 517 518 519 520
	depends on MFD_MAX77693
	depends on OF
	help
	  This option enables support for the flash part of the MAX77693
	  multifunction device. It has build in control for two leds in flash
	  and torch mode.

521 522 523 524 525 526 527
config LEDS_MAX8997
	tristate "LED support for MAX8997 PMIC"
	depends on LEDS_CLASS && MFD_MAX8997
	help
	  This option enables support for on-chip LED drivers on
	  MAXIM MAX8997 PMIC.

528 529
config LEDS_LM355x
	tristate "LED support for LM355x Chips, LM3554 and LM3556"
530 531 532
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
533 534
	  This option enables support for LEDs connected to LM355x.
	  LM355x includes Torch, Flash and Indicator functions.
535

536 537
config LEDS_OT200
	tristate "LED support for the Bachmann OT200"
J
Jean Delvare 已提交
538
	depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
539 540 541 542
	help
	  This option enables support for the LEDs on the Bachmann OT200.
	  Say Y to enable LEDs on the Bachmann OT200.

543 544 545 546 547 548 549 550 551
config LEDS_MENF21BMC
	tristate "LED support for the MEN 14F021P00 BMC"
	depends on LEDS_CLASS && MFD_MENF21BMC
	help
	  Say Y here to include support for the MEN 14F021P00 BMC LEDs.

	  This driver can also be built as a module. If so the module
	  will be called leds-menf21bmc.

I
Ingi Kim 已提交
552 553
config LEDS_KTD2692
	tristate "LED support for KTD2692 flash LED controller"
554 555
	depends on LEDS_CLASS_FLASH && OF
	depends on GPIOLIB || COMPILE_TEST
I
Ingi Kim 已提交
556 557 558 559 560 561
	help
	  This option enables support for KTD2692 LED flash connected
	  through ExpressWire interface.

	  Say Y to enable this driver.

562 563 564 565 566 567 568 569 570 571
config LEDS_SEAD3
	tristate "LED support for the MIPS SEAD 3 board"
	depends on LEDS_CLASS && MIPS_SEAD3
	help
	  Say Y here to include support for the FLED and PLED LEDs on SEAD3 eval
	  boards.

	  This driver can also be built as a module. If so the module
	  will be called leds-sead3.

572 573 574 575
config LEDS_IS31FL32XX
	tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
	depends on LEDS_CLASS && I2C && OF
	help
576 577 578
	  Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
	  LED controllers. They are I2C devices with multiple constant-current
	  channels, each with independent 256-level PWM control.
579

580 581
comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"

582 583 584 585 586 587 588 589
config LEDS_BLINKM
	tristate "LED support for the BlinkM I2C RGB LED"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the BlinkM RGB LED connected
	  through I2C. Say Y to enable support for the BlinkM LED.

590 591 592 593 594 595 596 597 598 599 600
config LEDS_POWERNV
	tristate "LED support for PowerNV Platform"
	depends on LEDS_CLASS
	depends on PPC_POWERNV
	depends on OF
	help
	  This option enables support for the system LEDs present on
	  PowerNV platforms. Say 'y' to enable this support in kernel.
	  To compile this driver as a module, choose 'm' here: the module
	  will be called leds-powernv.

601 602 603 604 605 606 607 608 609 610
config LEDS_SYSCON
	bool "LED support for LEDs on system controllers"
	depends on LEDS_CLASS=y
	depends on MFD_SYSCON
	depends on OF
	help
	  This option enabled support for the LEDs on syscon type
	  devices. This will only work with device tree enabled
	  devices.

611
config LEDS_VERSATILE
612
	tristate "LED support for the ARM Versatile and RealView"
613 614 615 616 617 618
	depends on ARCH_REALVIEW || ARCH_VERSATILE
	depends on LEDS_CLASS
	help
	  This option enabled support for the LEDs on the ARM Versatile
	  and RealView boards. Say Y to enabled these.

H
H Hartley Sweeten 已提交
619
comment "LED Triggers"
620
source "drivers/leds/trigger/Kconfig"
621

622
endif # NEW_LEDS