Kconfig 17.7 KB
Newer Older
1 2 3 4 5 6 7
config LEDS_GPIO_REGISTER
	bool
	help
	  This option provides the function gpio_led_register_device.
	  As this function is used by arch code it must not be compiled as a
	  module.

8
menuconfig NEW_LEDS
R
Richard Purdie 已提交
9 10
	bool "LED Support"
	help
11 12 13 14 15
	  Say Y to enable Linux LED support.  This allows control of supported
	  LEDs from both userspace and optionally, by kernel events (triggers).

	  This is not related to standard keyboard LEDs which are controlled
	  via the input system.
R
Richard Purdie 已提交
16

17 18
if NEW_LEDS

R
Richard Purdie 已提交
19
config LEDS_CLASS
20
	tristate "LED Class Support"
R
Richard Purdie 已提交
21 22 23 24
	help
	  This option enables the led sysfs class in /sys/class/leds.  You'll
	  need this to do anything useful with LEDs.  If unsure, say N.

25 26 27 28 29 30 31 32 33 34
config LEDS_CLASS_FLASH
	tristate "LED Flash Class Support"
	depends on LEDS_CLASS
	help
	  This option enables the flash led sysfs class in /sys/class/leds.
	  It wrapps LED Class and adds flash LEDs specific sysfs attributes
	  and kernel internal API to it. You'll need this to provide support
	  for the flash related features of a LED device. It can be built
	  as a module.

B
Ben Dooks 已提交
35
comment "LED drivers"
36

H
Haojian Zhuang 已提交
37 38
config LEDS_88PM860X
	tristate "LED Support for Marvell 88PM860x PMIC"
J
Johannes Berg 已提交
39
	depends on LEDS_CLASS
R
Richard Purdie 已提交
40
	depends on MFD_88PM860X
H
Haojian Zhuang 已提交
41 42 43 44
	help
	  This option enables support for on-chip LED drivers found on Marvell
	  Semiconductor 88PM8606 PMIC.

45 46 47 48 49 50 51 52
config LEDS_AAT1290
	tristate "LED support for the AAT1290"
	depends on LEDS_CLASS_FLASH
	depends on GPIOLIB
	depends on OF
	help
	 This option enables support for the LEDs on the AAT1290.

53 54 55 56 57 58 59 60
config LEDS_BCM6328
	tristate "LED Support for Broadcom BCM6328"
	depends on LEDS_CLASS
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6328
	  LED HW controller accessed via MMIO registers.

61 62 63 64 65 66 67 68
config LEDS_BCM6358
	tristate "LED Support for Broadcom BCM6358"
	depends on LEDS_CLASS
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6358
	  LED HW controller accessed via MMIO registers.

69 70 71 72 73 74 75 76 77 78
config LEDS_LM3530
	tristate "LCD Backlight driver for LM3530"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the LCD backlight using
	  LM3530 ambient light sensor chip. This ALS chip can be
	  controlled manually or using PWM input or using ambient
	  light automatically.

J
Johan Hovold 已提交
79 80 81 82 83 84 85 86 87 88 89 90 91
config LEDS_LM3533
	tristate "LED support for LM3533"
	depends on LEDS_CLASS
	depends on MFD_LM3533
	help
	  This option enables support for the LEDs on National Semiconductor /
	  TI LM3533 Lighting Power chips.

	  The LEDs can be controlled directly, through PWM input, or by the
	  ambient-light-sensor interface. The chip supports
	  hardware-accelerated blinking with maximum on and off periods of 9.8
	  and 77 seconds respectively.

92 93 94 95 96 97 98 99 100 101 102
config LEDS_LM3642
	tristate "LED support for LM3642 Chip"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to LM3642.
	  The LM3642 is a 4MHz fixed-frequency synchronous boost
	  converter plus 1.5A constant current driver for a high-current
	  white LED.


103 104
config LEDS_LOCOMO
	tristate "LED Support for Locomo device"
J
Johannes Berg 已提交
105
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
106
	depends on SHARP_LOCOMO
107 108 109 110
	help
	  This option enables support for the LEDs on Sharp Locomo.
	  Zaurus models SL-5500 and SL-5600.

111 112
config LEDS_MIKROTIK_RB532
	tristate "LED Support for Mikrotik Routerboard 532"
J
Johannes Berg 已提交
113
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
114
	depends on MIKROTIK_RB532
115 116 117 118
	help
	  This option enables support for the so called "User LED" of
	  Mikrotik's Routerboard 532.

B
Ben Dooks 已提交
119 120
config LEDS_S3C24XX
	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
J
Johannes Berg 已提交
121
	depends on LEDS_CLASS
122
	depends on ARCH_S3C24XX
B
Ben Dooks 已提交
123 124 125 126
	help
	  This option enables support for LEDs connected to GPIO lines
	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.

127 128
config LEDS_NET48XX
	tristate "LED Support for Soekris net48xx series Error LED"
J
Johannes Berg 已提交
129
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
130
	depends on SCx200_GPIO
131 132 133 134
	help
	  This option enables support for the Soekris net4801 and net4826 error
	  LED.

135 136
config LEDS_FSG
	tristate "LED Support for the Freecom FSG-3"
J
Johannes Berg 已提交
137
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
138
	depends on MACH_FSG
139 140 141
	help
	  This option enables support for the LEDs on the Freecom FSG-3.

142 143
config LEDS_WRAP
	tristate "LED Support for the WRAP series LEDs"
J
Johannes Berg 已提交
144
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
145
	depends on SCx200_GPIO
146 147 148
	help
	  This option enables support for the PCEngines WRAP programmable LEDs.

Y
Yoichi Yuasa 已提交
149 150
config LEDS_COBALT_QUBE
	tristate "LED Support for the Cobalt Qube series front LED"
J
Johannes Berg 已提交
151
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
152
	depends on MIPS_COBALT
153
	help
Y
Yoichi Yuasa 已提交
154
	  This option enables support for the front LED on Cobalt Qube series
155

156 157
config LEDS_COBALT_RAQ
	bool "LED Support for the Cobalt Raq series"
158
	depends on LEDS_CLASS=y && MIPS_COBALT
159 160 161 162
	select LEDS_TRIGGERS
	help
	  This option enables support for the Cobalt Raq series LEDs.

163 164
config LEDS_SUNFIRE
	tristate "LED support for SunFire servers."
J
Johannes Berg 已提交
165
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
166
	depends on SPARC64
167 168 169 170 171
	select LEDS_TRIGGERS
	help
	  This option enables support for the Left, Middle, and Right
	  LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.

172 173 174 175 176 177 178
config LEDS_IPAQ_MICRO
	tristate "LED Support for the Compaq iPAQ h3xxx"
	depends on MFD_IPAQ_MICRO
	help
	  Choose this option if you want to use the notification LED on
	  Compaq/HP iPAQ h3100 and h3600.

179 180
config LEDS_HP6XX
	tristate "LED Support for the HP Jornada 6xx"
J
Johannes Berg 已提交
181
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
182
	depends on SH_HP6XX
183
	help
184
	  This option enables LED support for the handheld
185 186
	  HP Jornada 620/660/680/690.

R
Riku Voipio 已提交
187 188
config LEDS_PCA9532
	tristate "LED driver for PCA9532 dimmer"
J
Johannes Berg 已提交
189
	depends on LEDS_CLASS
190
	depends on I2C && INPUT
R
Riku Voipio 已提交
191 192
	help
	  This option enables support for NXP pca9532
193
	  LED controller. It is generally only useful
R
Riku Voipio 已提交
194 195
	  as a platform driver

196 197 198 199 200 201 202 203 204 205
config LEDS_PCA9532_GPIO
	bool "Enable GPIO support for PCA9532"
	depends on LEDS_PCA9532
	depends on GPIOLIB
	help
	  Allow unused pins on PCA9532 to be used as gpio.

	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
	  set to PCA9532_TYPE_GPIO.

206 207
config LEDS_GPIO
	tristate "LED Support for GPIO connected LEDs"
J
Johannes Berg 已提交
208
	depends on LEDS_CLASS
209
	depends on GPIOLIB || COMPILE_TEST
210 211 212
	help
	  This option enables support for the LEDs connected to GPIO
	  outputs. To be useful the particular board must have LEDs
213 214 215 216
	  and they must be connected to the GPIO lines.  The LEDs must be
	  defined as platform devices and/or OpenFirmware platform devices.
	  The code to use these bindings can be selected below.

217 218
config LEDS_LP3944
	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
J
Johannes Berg 已提交
219
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
220
	depends on I2C
221
	help
222 223 224
	  This option enables support for LEDs connected to the National
	  Semiconductor LP3944 Lighting Management Unit (LMU) also known as
	  Fun Light Chip.
225 226 227 228

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp3944.

229
config LEDS_LP55XX_COMMON
230 231
	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
	depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
232
	select FW_LOADER
233
	help
234
	  This option supports common operations for LP5521/5523/55231/5562/8501
235 236
	  devices.

237 238 239
config LEDS_LP5521
	tristate "LED Support for N.S. LP5521 LED driver chip"
	depends on LEDS_CLASS && I2C
240
	select LEDS_LP55XX_COMMON
241 242 243 244 245 246 247
	help
	  If you say yes here you get support for the National Semiconductor
	  LP5521 LED driver. It is 3 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

config LEDS_LP5523
248
	tristate "LED Support for TI/National LP5523/55231 LED driver chip"
249
	depends on LEDS_CLASS && I2C
250
	select LEDS_LP55XX_COMMON
251
	help
252 253 254
	  If you say yes here you get support for TI/National Semiconductor
	  LP5523/55231 LED driver.
	  It is 9 channel chip with programmable engines.
255 256 257
	  Driver provides direct control via LED class and interface for
	  programming the engines.

K
Kim, Milo 已提交
258 259 260 261 262 263 264 265 266 267
config LEDS_LP5562
	tristate "LED Support for TI LP5562 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP5562 LED driver.
	  It is 4 channels chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

268 269 270 271 272 273 274 275 276 277 278 279
config LEDS_LP8501
	tristate "LED Support for TI LP8501 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP8501 LED driver.
	  It is 9 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.
	  It is similar as LP5523, but output power selection is available.
	  And register layout and engine program schemes are different.

K
Kim, Milo 已提交
280 281 282 283 284 285 286
config LEDS_LP8788
	tristate "LED support for the TI LP8788 PMIC"
	depends on LEDS_CLASS
	depends on MFD_LP8788
	help
	  This option enables support for the Keyboard LEDs on the LP8788 PMIC.

287 288
config LEDS_LP8860
	tristate "LED support for the TI LP8860 4 channel LED driver"
A
Axel Lin 已提交
289 290
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
291 292 293 294 295 296 297
	help
	  If you say yes here you get support for the TI LP8860 4 channel
	  LED driver.
	  This option enables support for the display cluster LEDs
	  on the LP8860 4 channel LED driver using the I2C communication
	  bus.

298
config LEDS_CLEVO_MAIL
299
	tristate "Mail LED on Clevo notebook"
J
Johannes Berg 已提交
300
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
301
	depends on X86 && SERIO_I8042 && DMI
302 303 304 305 306
	help
	  This driver makes the mail LED accessible from userspace
	  programs through the leds subsystem. This LED have three
	  known mode: off, blink at 0.5Hz and blink at 1Hz.

307 308 309 310 311
	  The driver supports two kinds of interface: using ledtrig-timer
	  or through /sys/class/leds/clevo::mail/brightness. As this LED
	  cannot change it's brightness it blinks instead. The brightness
	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
	  blink at 1Hz.
312 313 314

	  This module can drive the mail LED for the following notebooks:

315
	  	Clevo D400P
316 317 318 319 320 321 322
	  	Clevo D410J
	  	Clevo D410V
	  	Clevo D400V/D470V (not tested, but might work)
	  	Clevo M540N
	  	Clevo M5x0N (not tested, but might work)
	  	Positivo Mobile (Clevo M5x0V)

323
	  If your model is not listed here you can try the "nodetect"
324
	  module parameter.
325

326 327 328
	  To compile this driver as a module, choose M here: the
	  module will be called leds-clevo-mail.

329 330
config LEDS_PCA955X
	tristate "LED Support for PCA955x I2C chips"
J
Johannes Berg 已提交
331
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
332
	depends on I2C
333 334 335 336 337
	help
	  This option enables support for LEDs connected to PCA955x
	  LED driver chips accessed via the I2C bus.  Supported
	  devices include PCA9550, PCA9551, PCA9552, and PCA9553.

338
config LEDS_PCA963X
339
	tristate "LED support for PCA963x I2C chip"
340 341 342
	depends on LEDS_CLASS
	depends on I2C
	help
343 344 345
	  This option enables support for LEDs connected to the PCA963x
	  LED driver chip accessed via the I2C bus. Supported
	  devices include PCA9633 and PCA9634
346

M
Mark Brown 已提交
347 348
config LEDS_WM831X_STATUS
	tristate "LED support for status LEDs on WM831x PMICs"
J
Johannes Berg 已提交
349
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
350
	depends on MFD_WM831X
M
Mark Brown 已提交
351 352 353 354
	help
	  This option enables support for the status LEDs of the WM831x
          series of PMICs.

M
Mark Brown 已提交
355 356
config LEDS_WM8350
	tristate "LED Support for WM8350 AudioPlus PMIC"
J
Johannes Berg 已提交
357
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
358
	depends on MFD_WM8350
M
Mark Brown 已提交
359 360 361 362
	help
	  This option enables support for LEDs driven by the Wolfson
	  Microelectronics WM8350 AudioPlus PMIC.

363 364
config LEDS_DA903X
	tristate "LED Support for DA9030/DA9034 PMIC"
J
Johannes Berg 已提交
365
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
366
	depends on PMIC_DA903X
367 368 369 370
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9030/DA9034 PMICs.

371 372 373 374 375 376 377 378
config LEDS_DA9052
	tristate "Dialog DA9052/DA9053 LEDS"
	depends on LEDS_CLASS
	depends on PMIC_DA9052
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.

379 380
config LEDS_DAC124S085
	tristate "LED Support for DAC124S085 SPI DAC"
J
Johannes Berg 已提交
381
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
382
	depends on SPI
383 384 385 386
	help
	  This option enables support for DAC124S085 SPI DAC from NatSemi,
	  which can be used to control up to four LEDs.

387 388
config LEDS_PWM
	tristate "PWM driven LED Support"
J
Johannes Berg 已提交
389
	depends on LEDS_CLASS
390
	depends on PWM
391 392 393
	help
	  This option enables support for pwm driven LEDs

394 395
config LEDS_REGULATOR
	tristate "REGULATOR driven LED support"
J
Johannes Berg 已提交
396
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
397
	depends on REGULATOR
398 399 400
	help
	  This option enables support for regulator driven LEDs.

K
Kim Kyuwon 已提交
401 402
config LEDS_BD2802
	tristate "LED driver for BD2802 RGB LED"
J
Johannes Berg 已提交
403
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
404
	depends on I2C
K
Kim Kyuwon 已提交
405 406 407 408
	help
	  This option enables support for BD2802GU RGB LED driver chips
	  accessed via the I2C bus.

409 410
config LEDS_INTEL_SS4200
	tristate "LED driver for Intel NAS SS4200 series"
J
Johannes Berg 已提交
411
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
412
	depends on PCI && DMI
413 414 415 416 417 418
	help
	  This option enables support for the Intel SS4200 series of
	  Network Attached Storage servers.  You may control the hard
	  drive or power LEDs on the front panel.  Using this driver
	  can stop the front LED from blinking after startup.

419 420
config LEDS_LT3593
	tristate "LED driver for LT3593 controllers"
J
Johannes Berg 已提交
421
	depends on LEDS_CLASS
422
	depends on GPIOLIB
423 424 425 426 427
	help
	  This option enables support for LEDs driven by a Linear Technology
	  LT3593 controller. This controller uses a special one-wire pulse
	  coding protocol to set the brightness.

428 429
config LEDS_ADP5520
	tristate "LED Support for ADP5520/ADP5501 PMIC"
J
Johannes Berg 已提交
430
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
431
	depends on PMIC_ADP5520
432 433 434 435 436 437 438
	help
	  This option enables support for on-chip LED drivers found
	  on Analog Devices ADP5520/ADP5501 PMICs.

	  To compile this driver as a module, choose M here: the module will
	  be called leds-adp5520.

439 440
config LEDS_DELL_NETBOOKS
	tristate "External LED on Dell Business Netbooks"
J
Johannes Berg 已提交
441
	depends on LEDS_CLASS
442 443 444 445 446
	depends on X86 && ACPI_WMI
	help
	  This adds support for the Latitude 2100 and similar
	  notebooks that have an external LED.

447
config LEDS_MC13783
448
	tristate "LED Support for MC13XXX PMIC"
J
Johannes Berg 已提交
449
	depends on LEDS_CLASS
450
	depends on MFD_MC13XXX
451 452
	help
	  This option enable support for on-chip LED drivers found
453
	  on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
454

455 456
config LEDS_NS2
	tristate "LED support for Network Space v2 GPIO LEDs"
J
Johannes Berg 已提交
457
	depends on LEDS_CLASS
458
	depends on MACH_KIRKWOOD
459 460 461 462 463 464
	default y
	help
	  This option enable support for the dual-GPIO LED found on the
	  Network Space v2 board (and parents). This include Internet Space v2,
	  Network Space (Max) v2 and d2 Network v2 boards.

465 466
config LEDS_NETXBIG
	tristate "LED support for Big Network series LEDs"
467
	depends on LEDS_CLASS
468
	depends on MACH_KIRKWOOD
469 470 471 472 473 474
	default y
	help
	  This option enable support for LEDs found on the LaCie 2Big
	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
	  controlled through a GPIO extension bus.

P
Paul Parsons 已提交
475 476
config LEDS_ASIC3
	bool "LED support for the HTC ASIC3"
477
	depends on LEDS_CLASS=y
P
Paul Parsons 已提交
478 479 480 481 482 483 484 485
	depends on MFD_ASIC3
	default y
	help
	  This option enables support for the LEDs on the HTC ASIC3. The HTC
	  ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
	  cannot be used. This driver supports hardware blinking with an on+off
	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.

486 487 488 489 490 491 492 493
config LEDS_TCA6507
	tristate "LED Support for TCA6507 I2C chip"
	depends on LEDS_CLASS && I2C
	help
	  This option enables support for LEDs connected to TC6507
	  LED driver chips accessed via the I2C bus.
	  Driver support brightness control and hardware-assisted blinking.

494 495 496 497 498 499 500 501
config LEDS_TLC591XX
	tristate "LED driver for TLC59108 and TLC59116 controllers"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for Texas Instruments TLC59108
	  and TLC59116 LED controllers.

502 503 504 505 506 507 508 509 510 511
config LEDS_MAX77693
	tristate "LED support for MAX77693 Flash"
	depends on LEDS_CLASS_FLASH
	depends on MFD_MAX77693
	depends on OF
	help
	  This option enables support for the flash part of the MAX77693
	  multifunction device. It has build in control for two leds in flash
	  and torch mode.

512 513 514 515 516 517 518
config LEDS_MAX8997
	tristate "LED support for MAX8997 PMIC"
	depends on LEDS_CLASS && MFD_MAX8997
	help
	  This option enables support for on-chip LED drivers on
	  MAXIM MAX8997 PMIC.

519 520
config LEDS_LM355x
	tristate "LED support for LM355x Chips, LM3554 and LM3556"
521 522 523
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
524 525
	  This option enables support for LEDs connected to LM355x.
	  LM355x includes Torch, Flash and Indicator functions.
526

527 528
config LEDS_OT200
	tristate "LED support for the Bachmann OT200"
J
Jean Delvare 已提交
529
	depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
530 531 532 533
	help
	  This option enables support for the LEDs on the Bachmann OT200.
	  Say Y to enable LEDs on the Bachmann OT200.

534 535 536 537 538 539 540 541 542
config LEDS_MENF21BMC
	tristate "LED support for the MEN 14F021P00 BMC"
	depends on LEDS_CLASS && MFD_MENF21BMC
	help
	  Say Y here to include support for the MEN 14F021P00 BMC LEDs.

	  This driver can also be built as a module. If so the module
	  will be called leds-menf21bmc.

I
Ingi Kim 已提交
543 544 545 546 547 548 549 550 551
config LEDS_KTD2692
	tristate "LED support for KTD2692 flash LED controller"
	depends on LEDS_CLASS_FLASH && GPIOLIB && OF
	help
	  This option enables support for KTD2692 LED flash connected
	  through ExpressWire interface.

	  Say Y to enable this driver.

552 553
comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"

554 555 556 557 558 559 560 561
config LEDS_BLINKM
	tristate "LED support for the BlinkM I2C RGB LED"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the BlinkM RGB LED connected
	  through I2C. Say Y to enable support for the BlinkM LED.

562 563 564 565 566 567 568 569 570 571
config LEDS_SYSCON
	bool "LED support for LEDs on system controllers"
	depends on LEDS_CLASS=y
	depends on MFD_SYSCON
	depends on OF
	help
	  This option enabled support for the LEDs on syscon type
	  devices. This will only work with device tree enabled
	  devices.

572
config LEDS_VERSATILE
573
	tristate "LED support for the ARM Versatile and RealView"
574 575 576 577 578 579
	depends on ARCH_REALVIEW || ARCH_VERSATILE
	depends on LEDS_CLASS
	help
	  This option enabled support for the LEDs on the ARM Versatile
	  and RealView boards. Say Y to enabled these.

580 581 582 583 584 585 586 587
config LEDS_PM8941_WLED
	tristate "LED support for the Qualcomm PM8941 WLED block"
	depends on LEDS_CLASS
	select REGMAP
	help
	  This option enables support for the 'White' LED block
	  on Qualcomm PM8941 PMICs.

H
H Hartley Sweeten 已提交
588
comment "LED Triggers"
589
source "drivers/leds/trigger/Kconfig"
590

591
endif # NEW_LEDS