core.c 66.6 KB
Newer Older
L
Linus Torvalds 已提交
1
/*
2
 *  linux/drivers/mmc/core/core.c
L
Linus Torvalds 已提交
3 4
 *
 *  Copyright (C) 2003-2004 Russell King, All Rights Reserved.
P
Pierre Ossman 已提交
5
 *  SD support Copyright (C) 2004 Ian Molton, All Rights Reserved.
6
 *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
7
 *  MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved.
L
Linus Torvalds 已提交
8 9 10 11 12 13 14 15 16 17 18 19 20
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/completion.h>
#include <linux/device.h>
#include <linux/delay.h>
#include <linux/pagemap.h>
#include <linux/err.h>
P
Pierre Ossman 已提交
21
#include <linux/leds.h>
P
Pierre Ossman 已提交
22
#include <linux/scatterlist.h>
23
#include <linux/log2.h>
D
David Brownell 已提交
24
#include <linux/regulator/consumer.h>
25
#include <linux/pm_runtime.h>
26
#include <linux/pm_wakeup.h>
27
#include <linux/suspend.h>
P
Per Forlin 已提交
28 29
#include <linux/fault-inject.h>
#include <linux/random.h>
30
#include <linux/slab.h>
31
#include <linux/of.h>
L
Linus Torvalds 已提交
32 33 34

#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
P
Pierre Ossman 已提交
35 36
#include <linux/mmc/mmc.h>
#include <linux/mmc/sd.h>
L
Linus Torvalds 已提交
37

38
#include "core.h"
39 40
#include "bus.h"
#include "host.h"
P
Pierre Ossman 已提交
41
#include "sdio_bus.h"
P
Pierre Ossman 已提交
42 43 44

#include "mmc_ops.h"
#include "sd_ops.h"
P
Pierre Ossman 已提交
45
#include "sdio_ops.h"
L
Linus Torvalds 已提交
46

47 48 49
/* If the device is not responding */
#define MMC_CORE_TIMEOUT_MS	(10 * 60 * 1000) /* 10 minute timeout */

50 51 52 53 54 55
/*
 * Background operations can take a long time, depending on the housekeeping
 * operations the card has to perform.
 */
#define MMC_BKOPS_MAX_TIMEOUT	(4 * 60 * 1000) /* max time to wait in ms */

56
static struct workqueue_struct *workqueue;
57
static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };
58

D
David Brownell 已提交
59 60 61 62 63
/*
 * Enabling software CRCs on the data blocks can be a significant (30%)
 * performance cost, and for other reasons may not always be desired.
 * So we allow it it to be disabled.
 */
64
bool use_spi_crc = 1;
D
David Brownell 已提交
65 66
module_param(use_spi_crc, bool, 0);

67 68 69 70 71 72 73
/*
 * We normally treat cards as removed during suspend if they are not
 * known to be on a non-removable bus, to avoid the risk of writing
 * back data to a different card after resume.  Allow this to be
 * overridden if necessary.
 */
#ifdef CONFIG_MMC_UNSAFE_RESUME
74
bool mmc_assume_removable;
75
#else
76
bool mmc_assume_removable = 1;
77
#endif
78
EXPORT_SYMBOL(mmc_assume_removable);
79 80 81 82 83
module_param_named(removable, mmc_assume_removable, bool, 0644);
MODULE_PARM_DESC(
	removable,
	"MMC/SD cards are removable and may be removed during suspend");

84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
/*
 * Internal function. Schedule delayed work in the MMC work queue.
 */
static int mmc_schedule_delayed_work(struct delayed_work *work,
				     unsigned long delay)
{
	return queue_delayed_work(workqueue, work, delay);
}

/*
 * Internal function. Flush all scheduled work from the MMC work queue.
 */
static void mmc_flush_scheduled_work(void)
{
	flush_workqueue(workqueue);
}

P
Per Forlin 已提交
101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124
#ifdef CONFIG_FAIL_MMC_REQUEST

/*
 * Internal function. Inject random data errors.
 * If mmc_data is NULL no errors are injected.
 */
static void mmc_should_fail_request(struct mmc_host *host,
				    struct mmc_request *mrq)
{
	struct mmc_command *cmd = mrq->cmd;
	struct mmc_data *data = mrq->data;
	static const int data_errors[] = {
		-ETIMEDOUT,
		-EILSEQ,
		-EIO,
	};

	if (!data)
		return;

	if (cmd->error || data->error ||
	    !should_fail(&host->fail_mmc_request, data->blksz * data->blocks))
		return;

125 126
	data->error = data_errors[prandom_u32() % ARRAY_SIZE(data_errors)];
	data->bytes_xfered = (prandom_u32() % (data->bytes_xfered >> 9)) << 9;
P
Per Forlin 已提交
127 128 129 130 131 132 133 134 135 136 137
}

#else /* CONFIG_FAIL_MMC_REQUEST */

static inline void mmc_should_fail_request(struct mmc_host *host,
					   struct mmc_request *mrq)
{
}

#endif /* CONFIG_FAIL_MMC_REQUEST */

L
Linus Torvalds 已提交
138
/**
139 140 141
 *	mmc_request_done - finish processing an MMC request
 *	@host: MMC host which completed request
 *	@mrq: MMC request which request
L
Linus Torvalds 已提交
142 143
 *
 *	MMC drivers should call this function when they have completed
144
 *	their processing of a request.
L
Linus Torvalds 已提交
145 146 147 148
 */
void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq)
{
	struct mmc_command *cmd = mrq->cmd;
149 150
	int err = cmd->error;

D
David Brownell 已提交
151 152 153 154 155
	if (err && cmd->retries && mmc_host_is_spi(host)) {
		if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
			cmd->retries = 0;
	}

156
	if (err && cmd->retries && !mmc_card_removed(host->card)) {
157 158 159 160 161 162
		/*
		 * Request starter must handle retries - see
		 * mmc_wait_for_req_done().
		 */
		if (mrq->done)
			mrq->done(mrq);
163
	} else {
P
Per Forlin 已提交
164 165
		mmc_should_fail_request(host, mrq);

P
Pierre Ossman 已提交
166 167
		led_trigger_event(host->led, LED_OFF);

168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188
		pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n",
			mmc_hostname(host), cmd->opcode, err,
			cmd->resp[0], cmd->resp[1],
			cmd->resp[2], cmd->resp[3]);

		if (mrq->data) {
			pr_debug("%s:     %d bytes transferred: %d\n",
				mmc_hostname(host),
				mrq->data->bytes_xfered, mrq->data->error);
		}

		if (mrq->stop) {
			pr_debug("%s:     (CMD%u): %d: %08x %08x %08x %08x\n",
				mmc_hostname(host), mrq->stop->opcode,
				mrq->stop->error,
				mrq->stop->resp[0], mrq->stop->resp[1],
				mrq->stop->resp[2], mrq->stop->resp[3]);
		}

		if (mrq->done)
			mrq->done(mrq);
189

190
		mmc_host_clk_release(host);
L
Linus Torvalds 已提交
191 192 193 194 195
	}
}

EXPORT_SYMBOL(mmc_request_done);

196
static void
L
Linus Torvalds 已提交
197 198
mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
{
P
Pierre Ossman 已提交
199 200
#ifdef CONFIG_MMC_DEBUG
	unsigned int i, sz;
201
	struct scatterlist *sg;
P
Pierre Ossman 已提交
202 203
#endif

204 205 206 207 208 209
	if (mrq->sbc) {
		pr_debug("<%s: starting CMD%u arg %08x flags %08x>\n",
			 mmc_hostname(host), mrq->sbc->opcode,
			 mrq->sbc->arg, mrq->sbc->flags);
	}

210 211 212
	pr_debug("%s: starting CMD%u arg %08x flags %08x\n",
		 mmc_hostname(host), mrq->cmd->opcode,
		 mrq->cmd->arg, mrq->cmd->flags);
L
Linus Torvalds 已提交
213

214 215 216 217 218
	if (mrq->data) {
		pr_debug("%s:     blksz %d blocks %d flags %08x "
			"tsac %d ms nsac %d\n",
			mmc_hostname(host), mrq->data->blksz,
			mrq->data->blocks, mrq->data->flags,
219
			mrq->data->timeout_ns / 1000000,
220 221 222 223 224 225 226 227 228
			mrq->data->timeout_clks);
	}

	if (mrq->stop) {
		pr_debug("%s:     CMD%u arg %08x flags %08x\n",
			 mmc_hostname(host), mrq->stop->opcode,
			 mrq->stop->arg, mrq->stop->flags);
	}

P
Pierre Ossman 已提交
229
	WARN_ON(!host->claimed);
L
Linus Torvalds 已提交
230 231 232 233

	mrq->cmd->error = 0;
	mrq->cmd->mrq = mrq;
	if (mrq->data) {
234
		BUG_ON(mrq->data->blksz > host->max_blk_size);
235 236 237
		BUG_ON(mrq->data->blocks > host->max_blk_count);
		BUG_ON(mrq->data->blocks * mrq->data->blksz >
			host->max_req_size);
238

P
Pierre Ossman 已提交
239 240
#ifdef CONFIG_MMC_DEBUG
		sz = 0;
241 242
		for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i)
			sz += sg->length;
P
Pierre Ossman 已提交
243 244 245
		BUG_ON(sz != mrq->data->blocks * mrq->data->blksz);
#endif

L
Linus Torvalds 已提交
246 247 248 249 250 251 252 253 254
		mrq->cmd->data = mrq->data;
		mrq->data->error = 0;
		mrq->data->mrq = mrq;
		if (mrq->stop) {
			mrq->data->stop = mrq->stop;
			mrq->stop->error = 0;
			mrq->stop->mrq = mrq;
		}
	}
255
	mmc_host_clk_hold(host);
256
	led_trigger_event(host->led, LED_FULL);
L
Linus Torvalds 已提交
257 258 259
	host->ops->request(host, mrq);
}

260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304
/**
 *	mmc_start_bkops - start BKOPS for supported cards
 *	@card: MMC card to start BKOPS
 *	@form_exception: A flag to indicate if this function was
 *			 called due to an exception raised by the card
 *
 *	Start background operations whenever requested.
 *	When the urgent BKOPS bit is set in a R1 command response
 *	then background operations should be started immediately.
*/
void mmc_start_bkops(struct mmc_card *card, bool from_exception)
{
	int err;
	int timeout;
	bool use_busy_signal;

	BUG_ON(!card);

	if (!card->ext_csd.bkops_en || mmc_card_doing_bkops(card))
		return;

	err = mmc_read_bkops_status(card);
	if (err) {
		pr_err("%s: Failed to read bkops status: %d\n",
		       mmc_hostname(card->host), err);
		return;
	}

	if (!card->ext_csd.raw_bkops_status)
		return;

	if (card->ext_csd.raw_bkops_status < EXT_CSD_BKOPS_LEVEL_2 &&
	    from_exception)
		return;

	mmc_claim_host(card->host);
	if (card->ext_csd.raw_bkops_status >= EXT_CSD_BKOPS_LEVEL_2) {
		timeout = MMC_BKOPS_MAX_TIMEOUT;
		use_busy_signal = true;
	} else {
		timeout = 0;
		use_busy_signal = false;
	}

	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
305
			EXT_CSD_BKOPS_START, 1, timeout, use_busy_signal, true);
306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323
	if (err) {
		pr_warn("%s: Error %d starting bkops\n",
			mmc_hostname(card->host), err);
		goto out;
	}

	/*
	 * For urgent bkops status (LEVEL_2 and more)
	 * bkops executed synchronously, otherwise
	 * the operation is in progress
	 */
	if (!use_busy_signal)
		mmc_card_set_doing_bkops(card);
out:
	mmc_release_host(card->host);
}
EXPORT_SYMBOL(mmc_start_bkops);

324 325 326 327 328 329 330 331 332 333 334 335
/*
 * mmc_wait_data_done() - done callback for data request
 * @mrq: done data request
 *
 * Wakes up mmc context, passed as a callback to host controller driver
 */
static void mmc_wait_data_done(struct mmc_request *mrq)
{
	mrq->host->context_info.is_done_rcv = true;
	wake_up_interruptible(&mrq->host->context_info.wait);
}

L
Linus Torvalds 已提交
336 337
static void mmc_wait_done(struct mmc_request *mrq)
{
338 339 340
	complete(&mrq->completion);
}

341 342 343 344 345 346 347 348 349 350 351 352 353 354
/*
 *__mmc_start_data_req() - starts data request
 * @host: MMC host to start the request
 * @mrq: data request to start
 *
 * Sets the done callback to be called when request is completed by the card.
 * Starts data mmc request execution
 */
static int __mmc_start_data_req(struct mmc_host *host, struct mmc_request *mrq)
{
	mrq->done = mmc_wait_data_done;
	mrq->host = host;
	if (mmc_card_removed(host->card)) {
		mrq->cmd->error = -ENOMEDIUM;
355
		mmc_wait_data_done(mrq);
356 357 358 359 360 361 362
		return -ENOMEDIUM;
	}
	mmc_start_request(host, mrq);

	return 0;
}

363
static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq)
364 365 366
{
	init_completion(&mrq->completion);
	mrq->done = mmc_wait_done;
367 368 369
	if (mmc_card_removed(host->card)) {
		mrq->cmd->error = -ENOMEDIUM;
		complete(&mrq->completion);
370
		return -ENOMEDIUM;
371
	}
372
	mmc_start_request(host, mrq);
373
	return 0;
374 375
}

376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406
/*
 * mmc_wait_for_data_req_done() - wait for request completed
 * @host: MMC host to prepare the command.
 * @mrq: MMC request to wait for
 *
 * Blocks MMC context till host controller will ack end of data request
 * execution or new request notification arrives from the block layer.
 * Handles command retries.
 *
 * Returns enum mmc_blk_status after checking errors.
 */
static int mmc_wait_for_data_req_done(struct mmc_host *host,
				      struct mmc_request *mrq,
				      struct mmc_async_req *next_req)
{
	struct mmc_command *cmd;
	struct mmc_context_info *context_info = &host->context_info;
	int err;
	unsigned long flags;

	while (1) {
		wait_event_interruptible(context_info->wait,
				(context_info->is_done_rcv ||
				 context_info->is_new_req));
		spin_lock_irqsave(&context_info->lock, flags);
		context_info->is_waiting_last_req = false;
		spin_unlock_irqrestore(&context_info->lock, flags);
		if (context_info->is_done_rcv) {
			context_info->is_done_rcv = false;
			context_info->is_new_req = false;
			cmd = mrq->cmd;
407

408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432
			if (!cmd->error || !cmd->retries ||
			    mmc_card_removed(host->card)) {
				err = host->areq->err_check(host->card,
							    host->areq);
				break; /* return err */
			} else {
				pr_info("%s: req failed (CMD%u): %d, retrying...\n",
					mmc_hostname(host),
					cmd->opcode, cmd->error);
				cmd->retries--;
				cmd->error = 0;
				host->ops->request(host, mrq);
				continue; /* wait for done/new event again */
			}
		} else if (context_info->is_new_req) {
			context_info->is_new_req = false;
			if (!next_req) {
				err = MMC_BLK_NEW_REQUEST;
				break; /* return err */
			}
		}
	}
	return err;
}

433 434 435
static void mmc_wait_for_req_done(struct mmc_host *host,
				  struct mmc_request *mrq)
{
436 437 438 439 440 441
	struct mmc_command *cmd;

	while (1) {
		wait_for_completion(&mrq->completion);

		cmd = mrq->cmd;
442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459

		/*
		 * If host has timed out waiting for the sanitize
		 * to complete, card might be still in programming state
		 * so let's try to bring the card out of programming
		 * state.
		 */
		if (cmd->sanitize_busy && cmd->error == -ETIMEDOUT) {
			if (!mmc_interrupt_hpi(host->card)) {
				pr_warning("%s: %s: Interrupted sanitize\n",
					   mmc_hostname(host), __func__);
				cmd->error = 0;
				break;
			} else {
				pr_err("%s: %s: Failed to interrupt sanitize\n",
				       mmc_hostname(host), __func__);
			}
		}
460 461
		if (!cmd->error || !cmd->retries ||
		    mmc_card_removed(host->card))
462 463 464 465 466 467 468 469
			break;

		pr_debug("%s: req failed (CMD%u): %d, retrying...\n",
			 mmc_hostname(host), cmd->opcode, cmd->error);
		cmd->retries--;
		cmd->error = 0;
		host->ops->request(host, mrq);
	}
470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485
}

/**
 *	mmc_pre_req - Prepare for a new request
 *	@host: MMC host to prepare command
 *	@mrq: MMC request to prepare for
 *	@is_first_req: true if there is no previous started request
 *                     that may run in parellel to this call, otherwise false
 *
 *	mmc_pre_req() is called in prior to mmc_start_req() to let
 *	host prepare for the new request. Preparation of a request may be
 *	performed while another request is running on the host.
 */
static void mmc_pre_req(struct mmc_host *host, struct mmc_request *mrq,
		 bool is_first_req)
{
486 487
	if (host->ops->pre_req) {
		mmc_host_clk_hold(host);
488
		host->ops->pre_req(host, mrq, is_first_req);
489 490
		mmc_host_clk_release(host);
	}
491 492 493 494 495 496 497 498 499 500 501 502 503 504
}

/**
 *	mmc_post_req - Post process a completed request
 *	@host: MMC host to post process command
 *	@mrq: MMC request to post process for
 *	@err: Error, if non zero, clean up any resources made in pre_req
 *
 *	Let the host post process a completed request. Post processing of
 *	a request may be performed while another reuqest is running.
 */
static void mmc_post_req(struct mmc_host *host, struct mmc_request *mrq,
			 int err)
{
505 506
	if (host->ops->post_req) {
		mmc_host_clk_hold(host);
507
		host->ops->post_req(host, mrq, err);
508 509
		mmc_host_clk_release(host);
	}
L
Linus Torvalds 已提交
510 511
}

512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531
/**
 *	mmc_start_req - start a non-blocking request
 *	@host: MMC host to start command
 *	@areq: async request to start
 *	@error: out parameter returns 0 for success, otherwise non zero
 *
 *	Start a new MMC custom command request for a host.
 *	If there is on ongoing async request wait for completion
 *	of that request and start the new one and return.
 *	Does not wait for the new request to complete.
 *
 *      Returns the completed request, NULL in case of none completed.
 *	Wait for the an ongoing request (previoulsy started) to complete and
 *	return the completed request. If there is no ongoing request, NULL
 *	is returned without waiting. NULL is not an error condition.
 */
struct mmc_async_req *mmc_start_req(struct mmc_host *host,
				    struct mmc_async_req *areq, int *error)
{
	int err = 0;
532
	int start_err = 0;
533 534 535 536 537 538 539
	struct mmc_async_req *data = host->areq;

	/* Prepare a new request */
	if (areq)
		mmc_pre_req(host, areq->mrq, !host->areq);

	if (host->areq) {
J
Jaehoon Chung 已提交
540 541 542 543 544 545 546 547 548 549
		err = mmc_wait_for_data_req_done(host, host->areq->mrq,	areq);
		if (err == MMC_BLK_NEW_REQUEST) {
			if (error)
				*error = err;
			/*
			 * The previous request was not completed,
			 * nothing to return
			 */
			return NULL;
		}
550 551 552 553 554 555 556 557
		/*
		 * Check BKOPS urgency for each R1 response
		 */
		if (host->card && mmc_card_mmc(host->card) &&
		    ((mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1) ||
		     (mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1B)) &&
		    (host->areq->mrq->cmd->resp[0] & R1_EXCEPTION_EVENT))
			mmc_start_bkops(host->card, true);
558 559
	}

560
	if (!err && areq)
561
		start_err = __mmc_start_data_req(host, areq->mrq);
562 563 564 565

	if (host->areq)
		mmc_post_req(host, host->areq->mrq, 0);

566 567
	 /* Cancel a prepared request if it was not started. */
	if ((err || start_err) && areq)
J
Jaehoon Chung 已提交
568
		mmc_post_req(host, areq->mrq, -EINVAL);
569 570 571 572 573 574

	if (err)
		host->areq = NULL;
	else
		host->areq = areq;

575 576 577 578 579 580
	if (error)
		*error = err;
	return data;
}
EXPORT_SYMBOL(mmc_start_req);

P
Pierre Ossman 已提交
581 582 583 584 585 586 587 588 589 590
/**
 *	mmc_wait_for_req - start a request and wait for completion
 *	@host: MMC host to start command
 *	@mrq: MMC request to start
 *
 *	Start a new MMC custom command request for a host, and wait
 *	for the command to complete. Does not attempt to parse the
 *	response.
 */
void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq)
L
Linus Torvalds 已提交
591
{
592 593
	__mmc_start_req(host, mrq);
	mmc_wait_for_req_done(host, mrq);
L
Linus Torvalds 已提交
594 595 596
}
EXPORT_SYMBOL(mmc_wait_for_req);

597 598 599 600 601
/**
 *	mmc_interrupt_hpi - Issue for High priority Interrupt
 *	@card: the MMC card associated with the HPI transfer
 *
 *	Issued High Priority Interrupt, and check for card status
602
 *	until out-of prg-state.
603 604 605 606 607
 */
int mmc_interrupt_hpi(struct mmc_card *card)
{
	int err;
	u32 status;
608
	unsigned long prg_wait;
609 610 611 612 613 614 615 616 617 618 619 620 621 622 623

	BUG_ON(!card);

	if (!card->ext_csd.hpi_en) {
		pr_info("%s: HPI enable bit unset\n", mmc_hostname(card->host));
		return 1;
	}

	mmc_claim_host(card->host);
	err = mmc_send_status(card, &status);
	if (err) {
		pr_err("%s: Get card status fail\n", mmc_hostname(card->host));
		goto out;
	}

624 625 626 627
	switch (R1_CURRENT_STATE(status)) {
	case R1_STATE_IDLE:
	case R1_STATE_READY:
	case R1_STATE_STBY:
628
	case R1_STATE_TRAN:
629
		/*
630
		 * In idle and transfer states, HPI is not needed and the caller
631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656
		 * can issue the next intended command immediately
		 */
		goto out;
	case R1_STATE_PRG:
		break;
	default:
		/* In all other states, it's illegal to issue HPI */
		pr_debug("%s: HPI cannot be sent. Card state=%d\n",
			mmc_hostname(card->host), R1_CURRENT_STATE(status));
		err = -EINVAL;
		goto out;
	}

	err = mmc_send_hpi_cmd(card, &status);
	if (err)
		goto out;

	prg_wait = jiffies + msecs_to_jiffies(card->ext_csd.out_of_int_time);
	do {
		err = mmc_send_status(card, &status);

		if (!err && R1_CURRENT_STATE(status) == R1_STATE_TRAN)
			break;
		if (time_after(jiffies, prg_wait))
			err = -ETIMEDOUT;
	} while (!err);
657 658 659 660 661 662 663

out:
	mmc_release_host(card->host);
	return err;
}
EXPORT_SYMBOL(mmc_interrupt_hpi);

L
Linus Torvalds 已提交
664 665 666 667 668 669 670 671 672 673 674 675
/**
 *	mmc_wait_for_cmd - start a command and wait for completion
 *	@host: MMC host to start command
 *	@cmd: MMC command to start
 *	@retries: maximum number of retries
 *
 *	Start a new MMC command for a host, and wait for the command
 *	to complete.  Return any error that occurred while the command
 *	was executing.  Do not attempt to parse the response.
 */
int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd, int retries)
{
676
	struct mmc_request mrq = {NULL};
L
Linus Torvalds 已提交
677

P
Pierre Ossman 已提交
678
	WARN_ON(!host->claimed);
L
Linus Torvalds 已提交
679 680 681 682 683 684 685 686 687 688 689 690 691 692

	memset(cmd->resp, 0, sizeof(cmd->resp));
	cmd->retries = retries;

	mrq.cmd = cmd;
	cmd->data = NULL;

	mmc_wait_for_req(host, &mrq);

	return cmd->error;
}

EXPORT_SYMBOL(mmc_wait_for_cmd);

693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750
/**
 *	mmc_stop_bkops - stop ongoing BKOPS
 *	@card: MMC card to check BKOPS
 *
 *	Send HPI command to stop ongoing background operations to
 *	allow rapid servicing of foreground operations, e.g. read/
 *	writes. Wait until the card comes out of the programming state
 *	to avoid errors in servicing read/write requests.
 */
int mmc_stop_bkops(struct mmc_card *card)
{
	int err = 0;

	BUG_ON(!card);
	err = mmc_interrupt_hpi(card);

	/*
	 * If err is EINVAL, we can't issue an HPI.
	 * It should complete the BKOPS.
	 */
	if (!err || (err == -EINVAL)) {
		mmc_card_clr_doing_bkops(card);
		err = 0;
	}

	return err;
}
EXPORT_SYMBOL(mmc_stop_bkops);

int mmc_read_bkops_status(struct mmc_card *card)
{
	int err;
	u8 *ext_csd;

	/*
	 * In future work, we should consider storing the entire ext_csd.
	 */
	ext_csd = kmalloc(512, GFP_KERNEL);
	if (!ext_csd) {
		pr_err("%s: could not allocate buffer to receive the ext_csd.\n",
		       mmc_hostname(card->host));
		return -ENOMEM;
	}

	mmc_claim_host(card->host);
	err = mmc_send_ext_csd(card, ext_csd);
	mmc_release_host(card->host);
	if (err)
		goto out;

	card->ext_csd.raw_bkops_status = ext_csd[EXT_CSD_BKOPS_STATUS];
	card->ext_csd.raw_exception_status = ext_csd[EXT_CSD_EXP_EVENTS_STATUS];
out:
	kfree(ext_csd);
	return err;
}
EXPORT_SYMBOL(mmc_read_bkops_status);

751 752 753 754
/**
 *	mmc_set_data_timeout - set the timeout for a data command
 *	@data: data phase for command
 *	@card: the MMC card associated with the data transfer
P
Pierre Ossman 已提交
755 756 757
 *
 *	Computes the data timeout parameters according to the
 *	correct algorithm given the card type.
758
 */
759
void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card)
760 761 762
{
	unsigned int mult;

763 764 765 766 767 768 769 770 771
	/*
	 * SDIO cards only define an upper 1 s limit on access.
	 */
	if (mmc_card_sdio(card)) {
		data->timeout_ns = 1000000000;
		data->timeout_clks = 0;
		return;
	}

772 773 774 775 776 777 778 779 780
	/*
	 * SD cards use a 100 multiplier rather than 10
	 */
	mult = mmc_card_sd(card) ? 100 : 10;

	/*
	 * Scale up the multiplier (and therefore the timeout) by
	 * the r2w factor for writes.
	 */
781
	if (data->flags & MMC_DATA_WRITE)
782 783 784 785 786 787 788 789 790 791 792 793
		mult <<= card->csd.r2w_factor;

	data->timeout_ns = card->csd.tacc_ns * mult;
	data->timeout_clks = card->csd.tacc_clks * mult;

	/*
	 * SD cards also have an upper limit on the timeout.
	 */
	if (mmc_card_sd(card)) {
		unsigned int timeout_us, limit_us;

		timeout_us = data->timeout_ns / 1000;
794 795 796
		if (mmc_host_clk_rate(card->host))
			timeout_us += data->timeout_clks * 1000 /
				(mmc_host_clk_rate(card->host) / 1000);
797

798
		if (data->flags & MMC_DATA_WRITE)
799
			/*
800 801 802 803 804 805
			 * The MMC spec "It is strongly recommended
			 * for hosts to implement more than 500ms
			 * timeout value even if the card indicates
			 * the 250ms maximum busy length."  Even the
			 * previous value of 300ms is known to be
			 * insufficient for some cards.
806
			 */
807
			limit_us = 3000000;
808 809 810
		else
			limit_us = 100000;

811 812 813 814
		/*
		 * SDHC cards always use these fixed values.
		 */
		if (timeout_us > limit_us || mmc_card_blockaddr(card)) {
815 816 817 818
			data->timeout_ns = limit_us * 1000;
			data->timeout_clks = 0;
		}
	}
819 820 821 822 823 824 825 826 827 828 829 830

	/*
	 * Some cards require longer data read timeout than indicated in CSD.
	 * Address this by setting the read timeout to a "reasonably high"
	 * value. For the cards tested, 300ms has proven enough. If necessary,
	 * this value can be increased if other problematic cards require this.
	 */
	if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) {
		data->timeout_ns = 300000000;
		data->timeout_clks = 0;
	}

831 832 833 834 835 836 837 838 839 840 841 842 843 844 845
	/*
	 * Some cards need very high timeouts if driven in SPI mode.
	 * The worst observed timeout was 900ms after writing a
	 * continuous stream of data until the internal logic
	 * overflowed.
	 */
	if (mmc_host_is_spi(card->host)) {
		if (data->flags & MMC_DATA_WRITE) {
			if (data->timeout_ns < 1000000000)
				data->timeout_ns = 1000000000;	/* 1s */
		} else {
			if (data->timeout_ns < 100000000)
				data->timeout_ns =  100000000;	/* 100ms */
		}
	}
846 847 848
}
EXPORT_SYMBOL(mmc_set_data_timeout);

849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875
/**
 *	mmc_align_data_size - pads a transfer size to a more optimal value
 *	@card: the MMC card associated with the data transfer
 *	@sz: original transfer size
 *
 *	Pads the original data size with a number of extra bytes in
 *	order to avoid controller bugs and/or performance hits
 *	(e.g. some controllers revert to PIO for certain sizes).
 *
 *	Returns the improved size, which might be unmodified.
 *
 *	Note that this function is only relevant when issuing a
 *	single scatter gather entry.
 */
unsigned int mmc_align_data_size(struct mmc_card *card, unsigned int sz)
{
	/*
	 * FIXME: We don't have a system for the controller to tell
	 * the core about its problems yet, so for now we just 32-bit
	 * align the size.
	 */
	sz = ((sz + 3) / 4) * 4;

	return sz;
}
EXPORT_SYMBOL(mmc_align_data_size);

L
Linus Torvalds 已提交
876
/**
877
 *	__mmc_claim_host - exclusively claim a host
L
Linus Torvalds 已提交
878
 *	@host: mmc host to claim
879
 *	@abort: whether or not the operation should be aborted
L
Linus Torvalds 已提交
880
 *
881 882 883 884
 *	Claim a host for a set of operations.  If @abort is non null and
 *	dereference a non-zero value then this will return prematurely with
 *	that non-zero value without acquiring the lock.  Returns zero
 *	with the lock held otherwise.
L
Linus Torvalds 已提交
885
 */
886
int __mmc_claim_host(struct mmc_host *host, atomic_t *abort)
L
Linus Torvalds 已提交
887 888 889
{
	DECLARE_WAITQUEUE(wait, current);
	unsigned long flags;
890
	int stop;
L
Linus Torvalds 已提交
891

892 893
	might_sleep();

L
Linus Torvalds 已提交
894 895 896 897
	add_wait_queue(&host->wq, &wait);
	spin_lock_irqsave(&host->lock, flags);
	while (1) {
		set_current_state(TASK_UNINTERRUPTIBLE);
898
		stop = abort ? atomic_read(abort) : 0;
899
		if (stop || !host->claimed || host->claimer == current)
L
Linus Torvalds 已提交
900 901 902 903 904 905
			break;
		spin_unlock_irqrestore(&host->lock, flags);
		schedule();
		spin_lock_irqsave(&host->lock, flags);
	}
	set_current_state(TASK_RUNNING);
906
	if (!stop) {
907
		host->claimed = 1;
908 909 910
		host->claimer = current;
		host->claim_cnt += 1;
	} else
911
		wake_up(&host->wq);
L
Linus Torvalds 已提交
912 913
	spin_unlock_irqrestore(&host->lock, flags);
	remove_wait_queue(&host->wq, &wait);
914 915
	if (host->ops->enable && !stop && host->claim_cnt == 1)
		host->ops->enable(host);
916
	return stop;
L
Linus Torvalds 已提交
917 918
}

919
EXPORT_SYMBOL(__mmc_claim_host);
920

921
/**
922
 *	mmc_release_host - release a host
923 924
 *	@host: mmc host to release
 *
925 926
 *	Release a MMC host, allowing others to claim the host
 *	for their operations.
927
 */
928
void mmc_release_host(struct mmc_host *host)
929 930 931
{
	unsigned long flags;

932 933 934 935 936
	WARN_ON(!host->claimed);

	if (host->ops->disable && host->claim_cnt == 1)
		host->ops->disable(host);

937
	spin_lock_irqsave(&host->lock, flags);
938 939 940 941 942 943 944 945 946
	if (--host->claim_cnt) {
		/* Release for nested claim */
		spin_unlock_irqrestore(&host->lock, flags);
	} else {
		host->claimed = 0;
		host->claimer = NULL;
		spin_unlock_irqrestore(&host->lock, flags);
		wake_up(&host->wq);
	}
947
}
L
Linus Torvalds 已提交
948 949
EXPORT_SYMBOL(mmc_release_host);

950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972
/*
 * This is a helper function, which fetches a runtime pm reference for the
 * card device and also claims the host.
 */
void mmc_get_card(struct mmc_card *card)
{
	pm_runtime_get_sync(&card->dev);
	mmc_claim_host(card->host);
}
EXPORT_SYMBOL(mmc_get_card);

/*
 * This is a helper function, which releases the host and drops the runtime
 * pm reference for the card device.
 */
void mmc_put_card(struct mmc_card *card)
{
	mmc_release_host(card->host);
	pm_runtime_mark_last_busy(&card->dev);
	pm_runtime_put_autosuspend(&card->dev);
}
EXPORT_SYMBOL(mmc_put_card);

P
Pierre Ossman 已提交
973 974 975 976
/*
 * Internal function that does the actual ios call to the host driver,
 * optionally printing some debug output.
 */
977 978 979 980
static inline void mmc_set_ios(struct mmc_host *host)
{
	struct mmc_ios *ios = &host->ios;

981 982
	pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u "
		"width %u timing %u\n",
983 984
		 mmc_hostname(host), ios->clock, ios->bus_mode,
		 ios->power_mode, ios->chip_select, ios->vdd,
985
		 ios->bus_width, ios->timing);
986

987 988
	if (ios->clock > 0)
		mmc_set_ungated(host);
989 990 991
	host->ops->set_ios(host, ios);
}

P
Pierre Ossman 已提交
992 993 994
/*
 * Control chip select pin on a host.
 */
P
Pierre Ossman 已提交
995
void mmc_set_chip_select(struct mmc_host *host, int mode)
L
Linus Torvalds 已提交
996
{
997
	mmc_host_clk_hold(host);
P
Pierre Ossman 已提交
998 999
	host->ios.chip_select = mode;
	mmc_set_ios(host);
1000
	mmc_host_clk_release(host);
L
Linus Torvalds 已提交
1001 1002
}

P
Pierre Ossman 已提交
1003 1004 1005 1006
/*
 * Sets the host clock to the highest possible frequency that
 * is below "hz".
 */
1007
static void __mmc_set_clock(struct mmc_host *host, unsigned int hz)
P
Pierre Ossman 已提交
1008 1009 1010 1011 1012 1013 1014 1015 1016 1017
{
	WARN_ON(hz < host->f_min);

	if (hz > host->f_max)
		hz = host->f_max;

	host->ios.clock = hz;
	mmc_set_ios(host);
}

1018 1019 1020 1021 1022 1023 1024
void mmc_set_clock(struct mmc_host *host, unsigned int hz)
{
	mmc_host_clk_hold(host);
	__mmc_set_clock(host, hz);
	mmc_host_clk_release(host);
}

1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056
#ifdef CONFIG_MMC_CLKGATE
/*
 * This gates the clock by setting it to 0 Hz.
 */
void mmc_gate_clock(struct mmc_host *host)
{
	unsigned long flags;

	spin_lock_irqsave(&host->clk_lock, flags);
	host->clk_old = host->ios.clock;
	host->ios.clock = 0;
	host->clk_gated = true;
	spin_unlock_irqrestore(&host->clk_lock, flags);
	mmc_set_ios(host);
}

/*
 * This restores the clock from gating by using the cached
 * clock value.
 */
void mmc_ungate_clock(struct mmc_host *host)
{
	/*
	 * We should previously have gated the clock, so the clock shall
	 * be 0 here! The clock may however be 0 during initialization,
	 * when some request operations are performed before setting
	 * the frequency. When ungate is requested in that situation
	 * we just ignore the call.
	 */
	if (host->clk_old) {
		BUG_ON(host->ios.clock);
		/* This call will also set host->clk_gated to false */
1057
		__mmc_set_clock(host, host->clk_old);
1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079
	}
}

void mmc_set_ungated(struct mmc_host *host)
{
	unsigned long flags;

	/*
	 * We've been given a new frequency while the clock is gated,
	 * so make sure we regard this as ungating it.
	 */
	spin_lock_irqsave(&host->clk_lock, flags);
	host->clk_gated = false;
	spin_unlock_irqrestore(&host->clk_lock, flags);
}

#else
void mmc_set_ungated(struct mmc_host *host)
{
}
#endif

P
Pierre Ossman 已提交
1080 1081 1082 1083 1084
/*
 * Change the bus mode (open drain/push-pull) of a host.
 */
void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode)
{
1085
	mmc_host_clk_hold(host);
P
Pierre Ossman 已提交
1086 1087
	host->ios.bus_mode = mode;
	mmc_set_ios(host);
1088
	mmc_host_clk_release(host);
P
Pierre Ossman 已提交
1089 1090
}

1091 1092 1093 1094 1095
/*
 * Change data bus width of a host.
 */
void mmc_set_bus_width(struct mmc_host *host, unsigned int width)
{
1096
	mmc_host_clk_hold(host);
1097 1098
	host->ios.bus_width = width;
	mmc_set_ios(host);
1099
	mmc_host_clk_release(host);
1100 1101
}

1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175
/**
 * mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number
 * @vdd:	voltage (mV)
 * @low_bits:	prefer low bits in boundary cases
 *
 * This function returns the OCR bit number according to the provided @vdd
 * value. If conversion is not possible a negative errno value returned.
 *
 * Depending on the @low_bits flag the function prefers low or high OCR bits
 * on boundary voltages. For example,
 * with @low_bits = true, 3300 mV translates to ilog2(MMC_VDD_32_33);
 * with @low_bits = false, 3300 mV translates to ilog2(MMC_VDD_33_34);
 *
 * Any value in the [1951:1999] range translates to the ilog2(MMC_VDD_20_21).
 */
static int mmc_vdd_to_ocrbitnum(int vdd, bool low_bits)
{
	const int max_bit = ilog2(MMC_VDD_35_36);
	int bit;

	if (vdd < 1650 || vdd > 3600)
		return -EINVAL;

	if (vdd >= 1650 && vdd <= 1950)
		return ilog2(MMC_VDD_165_195);

	if (low_bits)
		vdd -= 1;

	/* Base 2000 mV, step 100 mV, bit's base 8. */
	bit = (vdd - 2000) / 100 + 8;
	if (bit > max_bit)
		return max_bit;
	return bit;
}

/**
 * mmc_vddrange_to_ocrmask - Convert a voltage range to the OCR mask
 * @vdd_min:	minimum voltage value (mV)
 * @vdd_max:	maximum voltage value (mV)
 *
 * This function returns the OCR mask bits according to the provided @vdd_min
 * and @vdd_max values. If conversion is not possible the function returns 0.
 *
 * Notes wrt boundary cases:
 * This function sets the OCR bits for all boundary voltages, for example
 * [3300:3400] range is translated to MMC_VDD_32_33 | MMC_VDD_33_34 |
 * MMC_VDD_34_35 mask.
 */
u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max)
{
	u32 mask = 0;

	if (vdd_max < vdd_min)
		return 0;

	/* Prefer high bits for the boundary vdd_max values. */
	vdd_max = mmc_vdd_to_ocrbitnum(vdd_max, false);
	if (vdd_max < 0)
		return 0;

	/* Prefer low bits for the boundary vdd_min values. */
	vdd_min = mmc_vdd_to_ocrbitnum(vdd_min, true);
	if (vdd_min < 0)
		return 0;

	/* Fill the mask, from max bit to min bit. */
	while (vdd_max >= vdd_min)
		mask |= 1 << vdd_max--;

	return mask;
}
EXPORT_SYMBOL(mmc_vddrange_to_ocrmask);

1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218
#ifdef CONFIG_OF

/**
 * mmc_of_parse_voltage - return mask of supported voltages
 * @np: The device node need to be parsed.
 * @mask: mask of voltages available for MMC/SD/SDIO
 *
 * 1. Return zero on success.
 * 2. Return negative errno: voltage-range is invalid.
 */
int mmc_of_parse_voltage(struct device_node *np, u32 *mask)
{
	const u32 *voltage_ranges;
	int num_ranges, i;

	voltage_ranges = of_get_property(np, "voltage-ranges", &num_ranges);
	num_ranges = num_ranges / sizeof(*voltage_ranges) / 2;
	if (!voltage_ranges || !num_ranges) {
		pr_info("%s: voltage-ranges unspecified\n", np->full_name);
		return -EINVAL;
	}

	for (i = 0; i < num_ranges; i++) {
		const int j = i * 2;
		u32 ocr_mask;

		ocr_mask = mmc_vddrange_to_ocrmask(
				be32_to_cpu(voltage_ranges[j]),
				be32_to_cpu(voltage_ranges[j + 1]));
		if (!ocr_mask) {
			pr_err("%s: voltage-range #%d is invalid\n",
				np->full_name, i);
			return -EINVAL;
		}
		*mask |= ocr_mask;
	}

	return 0;
}
EXPORT_SYMBOL(mmc_of_parse_voltage);

#endif /* CONFIG_OF */

D
David Brownell 已提交
1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253
#ifdef CONFIG_REGULATOR

/**
 * mmc_regulator_get_ocrmask - return mask of supported voltages
 * @supply: regulator to use
 *
 * This returns either a negative errno, or a mask of voltages that
 * can be provided to MMC/SD/SDIO devices using the specified voltage
 * regulator.  This would normally be called before registering the
 * MMC host adapter.
 */
int mmc_regulator_get_ocrmask(struct regulator *supply)
{
	int			result = 0;
	int			count;
	int			i;

	count = regulator_count_voltages(supply);
	if (count < 0)
		return count;

	for (i = 0; i < count; i++) {
		int		vdd_uV;
		int		vdd_mV;

		vdd_uV = regulator_list_voltage(supply, i);
		if (vdd_uV <= 0)
			continue;

		vdd_mV = vdd_uV / 1000;
		result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV);
	}

	return result;
}
1254
EXPORT_SYMBOL_GPL(mmc_regulator_get_ocrmask);
D
David Brownell 已提交
1255 1256 1257

/**
 * mmc_regulator_set_ocr - set regulator to match host->ios voltage
1258
 * @mmc: the host to regulate
D
David Brownell 已提交
1259
 * @supply: regulator to use
1260
 * @vdd_bit: zero for power off, else a bit number (host->ios.vdd)
D
David Brownell 已提交
1261 1262 1263 1264 1265 1266 1267
 *
 * Returns zero on success, else negative errno.
 *
 * MMC host drivers may use this to enable or disable a regulator using
 * a particular supply voltage.  This would normally be called from the
 * set_ios() method.
 */
1268 1269 1270
int mmc_regulator_set_ocr(struct mmc_host *mmc,
			struct regulator *supply,
			unsigned short vdd_bit)
D
David Brownell 已提交
1271 1272 1273 1274 1275 1276 1277 1278
{
	int			result = 0;
	int			min_uV, max_uV;

	if (vdd_bit) {
		int		tmp;
		int		voltage;

1279 1280
		/*
		 * REVISIT mmc_vddrange_to_ocrmask() may have set some
D
David Brownell 已提交
1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293
		 * bits this regulator doesn't quite support ... don't
		 * be too picky, most cards and regulators are OK with
		 * a 0.1V range goof (it's a small error percentage).
		 */
		tmp = vdd_bit - ilog2(MMC_VDD_165_195);
		if (tmp == 0) {
			min_uV = 1650 * 1000;
			max_uV = 1950 * 1000;
		} else {
			min_uV = 1900 * 1000 + tmp * 100 * 1000;
			max_uV = min_uV + 100 * 1000;
		}

1294 1295 1296
		/*
		 * If we're using a fixed/static regulator, don't call
		 * regulator_set_voltage; it would fail.
D
David Brownell 已提交
1297 1298
		 */
		voltage = regulator_get_voltage(supply);
1299

1300
		if (!regulator_can_change_voltage(supply))
1301 1302
			min_uV = max_uV = voltage;

D
David Brownell 已提交
1303 1304 1305 1306 1307 1308 1309
		if (voltage < 0)
			result = voltage;
		else if (voltage < min_uV || voltage > max_uV)
			result = regulator_set_voltage(supply, min_uV, max_uV);
		else
			result = 0;

1310
		if (result == 0 && !mmc->regulator_enabled) {
D
David Brownell 已提交
1311
			result = regulator_enable(supply);
1312 1313 1314 1315
			if (!result)
				mmc->regulator_enabled = true;
		}
	} else if (mmc->regulator_enabled) {
D
David Brownell 已提交
1316
		result = regulator_disable(supply);
1317 1318
		if (result == 0)
			mmc->regulator_enabled = false;
D
David Brownell 已提交
1319 1320
	}

1321 1322 1323
	if (result)
		dev_err(mmc_dev(mmc),
			"could not set regulator OCR (%d)\n", result);
D
David Brownell 已提交
1324 1325
	return result;
}
1326
EXPORT_SYMBOL_GPL(mmc_regulator_set_ocr);
D
David Brownell 已提交
1327

1328 1329 1330 1331 1332 1333 1334 1335
int mmc_regulator_get_supply(struct mmc_host *mmc)
{
	struct device *dev = mmc_dev(mmc);
	struct regulator *supply;
	int ret;

	supply = devm_regulator_get(dev, "vmmc");
	mmc->supply.vmmc = supply;
1336
	mmc->supply.vqmmc = devm_regulator_get_optional(dev, "vqmmc");
1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350

	if (IS_ERR(supply))
		return PTR_ERR(supply);

	ret = mmc_regulator_get_ocrmask(supply);
	if (ret > 0)
		mmc->ocr_avail = ret;
	else
		dev_warn(mmc_dev(mmc), "Failed getting OCR mask: %d\n", ret);

	return 0;
}
EXPORT_SYMBOL_GPL(mmc_regulator_get_supply);

1351
#endif /* CONFIG_REGULATOR */
D
David Brownell 已提交
1352

L
Linus Torvalds 已提交
1353 1354 1355 1356
/*
 * Mask off any voltages we don't support and select
 * the lowest voltage
 */
P
Pierre Ossman 已提交
1357
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
L
Linus Torvalds 已提交
1358 1359 1360
{
	int bit;

1361 1362 1363 1364 1365 1366 1367 1368 1369 1370
	/*
	 * Sanity check the voltages that the card claims to
	 * support.
	 */
	if (ocr & 0x7F) {
		dev_warn(mmc_dev(host),
		"card claims to support voltages below defined range\n");
		ocr &= ~0x7F;
	}

L
Linus Torvalds 已提交
1371
	ocr &= host->ocr_avail;
1372 1373 1374 1375
	if (!ocr) {
		dev_warn(mmc_dev(host), "no support for card's volts\n");
		return 0;
	}
L
Linus Torvalds 已提交
1376

1377 1378
	if (host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) {
		bit = ffs(ocr) - 1;
1379
		ocr &= 3 << bit;
1380
		mmc_power_cycle(host, ocr);
L
Linus Torvalds 已提交
1381
	} else {
1382 1383 1384 1385
		bit = fls(ocr) - 1;
		ocr &= 3 << bit;
		if (bit != host->ios.vdd)
			dev_warn(mmc_dev(host), "exceeding card's volts\n");
L
Linus Torvalds 已提交
1386 1387 1388 1389 1390
	}

	return ocr;
}

1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409
int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
{
	int err = 0;
	int old_signal_voltage = host->ios.signal_voltage;

	host->ios.signal_voltage = signal_voltage;
	if (host->ops->start_signal_voltage_switch) {
		mmc_host_clk_hold(host);
		err = host->ops->start_signal_voltage_switch(host, &host->ios);
		mmc_host_clk_release(host);
	}

	if (err)
		host->ios.signal_voltage = old_signal_voltage;

	return err;

}

1410
int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr)
1411 1412 1413
{
	struct mmc_command cmd = {0};
	int err = 0;
1414
	u32 clock;
1415 1416 1417 1418 1419 1420 1421

	BUG_ON(!host);

	/*
	 * Send CMD11 only if the request is to switch the card to
	 * 1.8V signalling.
	 */
1422 1423
	if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
		return __mmc_set_signal_voltage(host, signal_voltage);
1424

1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462
	/*
	 * If we cannot switch voltages, return failure so the caller
	 * can continue without UHS mode
	 */
	if (!host->ops->start_signal_voltage_switch)
		return -EPERM;
	if (!host->ops->card_busy)
		pr_warning("%s: cannot verify signal voltage switch\n",
				mmc_hostname(host));

	cmd.opcode = SD_SWITCH_VOLTAGE;
	cmd.arg = 0;
	cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;

	err = mmc_wait_for_cmd(host, &cmd, 0);
	if (err)
		return err;

	if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
		return -EIO;

	mmc_host_clk_hold(host);
	/*
	 * The card should drive cmd and dat[0:3] low immediately
	 * after the response of cmd11, but wait 1 ms to be sure
	 */
	mmc_delay(1);
	if (host->ops->card_busy && !host->ops->card_busy(host)) {
		err = -EAGAIN;
		goto power_cycle;
	}
	/*
	 * During a signal voltage level switch, the clock must be gated
	 * for 5 ms according to the SD spec
	 */
	clock = host->ios.clock;
	host->ios.clock = 0;
	mmc_set_ios(host);
1463

1464 1465 1466 1467 1468 1469 1470
	if (__mmc_set_signal_voltage(host, signal_voltage)) {
		/*
		 * Voltages may not have been switched, but we've already
		 * sent CMD11, so a power cycle is required anyway
		 */
		err = -EAGAIN;
		goto power_cycle;
1471 1472
	}

1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491
	/* Keep clock gated for at least 5 ms */
	mmc_delay(5);
	host->ios.clock = clock;
	mmc_set_ios(host);

	/* Wait for at least 1 ms according to spec */
	mmc_delay(1);

	/*
	 * Failure to switch is indicated by the card holding
	 * dat[0:3] low
	 */
	if (host->ops->card_busy && host->ops->card_busy(host))
		err = -EAGAIN;

power_cycle:
	if (err) {
		pr_debug("%s: Signal voltage switch failed, "
			"power cycling card\n", mmc_hostname(host));
1492
		mmc_power_cycle(host, ocr);
1493 1494 1495 1496 1497
	}

	mmc_host_clk_release(host);

	return err;
1498 1499
}

P
Pierre Ossman 已提交
1500
/*
P
Pierre Ossman 已提交
1501
 * Select timing parameters for host.
P
Pierre Ossman 已提交
1502
 */
P
Pierre Ossman 已提交
1503
void mmc_set_timing(struct mmc_host *host, unsigned int timing)
P
Pierre Ossman 已提交
1504
{
1505
	mmc_host_clk_hold(host);
P
Pierre Ossman 已提交
1506 1507
	host->ios.timing = timing;
	mmc_set_ios(host);
1508
	mmc_host_clk_release(host);
P
Pierre Ossman 已提交
1509 1510
}

1511 1512 1513 1514 1515
/*
 * Select appropriate driver type for host.
 */
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type)
{
1516
	mmc_host_clk_hold(host);
1517 1518
	host->ios.drv_type = drv_type;
	mmc_set_ios(host);
1519
	mmc_host_clk_release(host);
1520 1521
}

L
Linus Torvalds 已提交
1522
/*
1523 1524 1525 1526 1527 1528 1529 1530 1531
 * Apply power to the MMC stack.  This is a two-stage process.
 * First, we enable power to the card without the clock running.
 * We then wait a bit for the power to stabilise.  Finally,
 * enable the bus drivers and clock to the card.
 *
 * We must _NOT_ enable the clock prior to power stablising.
 *
 * If a host does all the power sequencing itself, ignore the
 * initial MMC_POWER_UP stage.
L
Linus Torvalds 已提交
1532
 */
1533
void mmc_power_up(struct mmc_host *host, u32 ocr)
L
Linus Torvalds 已提交
1534
{
1535 1536 1537
	if (host->ios.power_mode == MMC_POWER_ON)
		return;

1538 1539
	mmc_host_clk_hold(host);

1540
	host->ios.vdd = fls(ocr) - 1;
1541
	if (mmc_host_is_spi(host))
D
David Brownell 已提交
1542
		host->ios.chip_select = MMC_CS_HIGH;
1543
	else
D
David Brownell 已提交
1544
		host->ios.chip_select = MMC_CS_DONTCARE;
1545
	host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
L
Linus Torvalds 已提交
1546
	host->ios.power_mode = MMC_POWER_UP;
P
Pierre Ossman 已提交
1547
	host->ios.bus_width = MMC_BUS_WIDTH_1;
1548
	host->ios.timing = MMC_TIMING_LEGACY;
1549
	mmc_set_ios(host);
L
Linus Torvalds 已提交
1550

1551
	/* Set signal voltage to 3.3V */
1552
	__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
1553

P
Pierre Ossman 已提交
1554 1555 1556 1557
	/*
	 * This delay should be sufficient to allow the power supply
	 * to reach the minimum voltage.
	 */
1558
	mmc_delay(10);
L
Linus Torvalds 已提交
1559

H
Hein Tibosch 已提交
1560
	host->ios.clock = host->f_init;
1561

L
Linus Torvalds 已提交
1562
	host->ios.power_mode = MMC_POWER_ON;
1563
	mmc_set_ios(host);
L
Linus Torvalds 已提交
1564

P
Pierre Ossman 已提交
1565 1566 1567 1568
	/*
	 * This delay must be at least 74 clock sizes, or 1 ms, or the
	 * time required to reach a stable voltage.
	 */
1569
	mmc_delay(10);
1570 1571

	mmc_host_clk_release(host);
L
Linus Torvalds 已提交
1572 1573
}

1574
void mmc_power_off(struct mmc_host *host)
L
Linus Torvalds 已提交
1575
{
1576 1577 1578
	if (host->ios.power_mode == MMC_POWER_OFF)
		return;

1579 1580
	mmc_host_clk_hold(host);

L
Linus Torvalds 已提交
1581 1582
	host->ios.clock = 0;
	host->ios.vdd = 0;
1583

D
David Brownell 已提交
1584 1585 1586 1587
	if (!mmc_host_is_spi(host)) {
		host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
		host->ios.chip_select = MMC_CS_DONTCARE;
	}
L
Linus Torvalds 已提交
1588
	host->ios.power_mode = MMC_POWER_OFF;
P
Pierre Ossman 已提交
1589
	host->ios.bus_width = MMC_BUS_WIDTH_1;
1590
	host->ios.timing = MMC_TIMING_LEGACY;
1591
	mmc_set_ios(host);
1592

1593 1594 1595 1596 1597 1598 1599
	/*
	 * Some configurations, such as the 802.11 SDIO card in the OLPC
	 * XO-1.5, require a short delay after poweroff before the card
	 * can be successfully turned on again.
	 */
	mmc_delay(1);

1600
	mmc_host_clk_release(host);
L
Linus Torvalds 已提交
1601 1602
}

1603
void mmc_power_cycle(struct mmc_host *host, u32 ocr)
J
Johan Rudholm 已提交
1604 1605 1606 1607
{
	mmc_power_off(host);
	/* Wait at least 1 ms according to SD spec */
	mmc_delay(1);
1608
	mmc_power_up(host, ocr);
J
Johan Rudholm 已提交
1609 1610
}

1611 1612 1613
/*
 * Cleanup when the last reference to the bus operator is dropped.
 */
1614
static void __mmc_release_bus(struct mmc_host *host)
1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649
{
	BUG_ON(!host);
	BUG_ON(host->bus_refs);
	BUG_ON(!host->bus_dead);

	host->bus_ops = NULL;
}

/*
 * Increase reference count of bus operator
 */
static inline void mmc_bus_get(struct mmc_host *host)
{
	unsigned long flags;

	spin_lock_irqsave(&host->lock, flags);
	host->bus_refs++;
	spin_unlock_irqrestore(&host->lock, flags);
}

/*
 * Decrease reference count of bus operator and free it if
 * it is the last reference.
 */
static inline void mmc_bus_put(struct mmc_host *host)
{
	unsigned long flags;

	spin_lock_irqsave(&host->lock, flags);
	host->bus_refs--;
	if ((host->bus_refs == 0) && host->bus_ops)
		__mmc_release_bus(host);
	spin_unlock_irqrestore(&host->lock, flags);
}

L
Linus Torvalds 已提交
1650
/*
P
Pierre Ossman 已提交
1651 1652
 * Assign a mmc bus handler to a host. Only one bus handler may control a
 * host at any given time.
L
Linus Torvalds 已提交
1653
 */
P
Pierre Ossman 已提交
1654
void mmc_attach_bus(struct mmc_host *host, const struct mmc_bus_ops *ops)
L
Linus Torvalds 已提交
1655
{
P
Pierre Ossman 已提交
1656
	unsigned long flags;
1657

P
Pierre Ossman 已提交
1658 1659
	BUG_ON(!host);
	BUG_ON(!ops);
P
Pierre Ossman 已提交
1660

P
Pierre Ossman 已提交
1661
	WARN_ON(!host->claimed);
1662

P
Pierre Ossman 已提交
1663
	spin_lock_irqsave(&host->lock, flags);
1664

P
Pierre Ossman 已提交
1665 1666
	BUG_ON(host->bus_ops);
	BUG_ON(host->bus_refs);
P
Pierre Ossman 已提交
1667

P
Pierre Ossman 已提交
1668 1669 1670
	host->bus_ops = ops;
	host->bus_refs = 1;
	host->bus_dead = 0;
P
Pierre Ossman 已提交
1671

P
Pierre Ossman 已提交
1672
	spin_unlock_irqrestore(&host->lock, flags);
P
Pierre Ossman 已提交
1673 1674
}

P
Pierre Ossman 已提交
1675
/*
1676
 * Remove the current bus handler from a host.
P
Pierre Ossman 已提交
1677 1678
 */
void mmc_detach_bus(struct mmc_host *host)
1679
{
P
Pierre Ossman 已提交
1680
	unsigned long flags;
1681

P
Pierre Ossman 已提交
1682
	BUG_ON(!host);
1683

P
Pierre Ossman 已提交
1684 1685
	WARN_ON(!host->claimed);
	WARN_ON(!host->bus_ops);
1686

P
Pierre Ossman 已提交
1687
	spin_lock_irqsave(&host->lock, flags);
1688

P
Pierre Ossman 已提交
1689
	host->bus_dead = 1;
1690

P
Pierre Ossman 已提交
1691
	spin_unlock_irqrestore(&host->lock, flags);
L
Linus Torvalds 已提交
1692

P
Pierre Ossman 已提交
1693
	mmc_bus_put(host);
L
Linus Torvalds 已提交
1694 1695
}

1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717
static void _mmc_detect_change(struct mmc_host *host, unsigned long delay,
				bool cd_irq)
{
#ifdef CONFIG_MMC_DEBUG
	unsigned long flags;
	spin_lock_irqsave(&host->lock, flags);
	WARN_ON(host->removed);
	spin_unlock_irqrestore(&host->lock, flags);
#endif

	/*
	 * If the device is configured as wakeup, we prevent a new sleep for
	 * 5 s to give provision for user space to consume the event.
	 */
	if (cd_irq && !(host->caps & MMC_CAP_NEEDS_POLL) &&
		device_can_wakeup(mmc_dev(host)))
		pm_wakeup_event(mmc_dev(host), 5000);

	host->detect_change = 1;
	mmc_schedule_delayed_work(&host->detect, delay);
}

L
Linus Torvalds 已提交
1718 1719 1720
/**
 *	mmc_detect_change - process change of state on a MMC socket
 *	@host: host which changed state.
1721
 *	@delay: optional delay to wait before detection (jiffies)
L
Linus Torvalds 已提交
1722
 *
P
Pierre Ossman 已提交
1723 1724 1725 1726
 *	MMC drivers should call this when they detect a card has been
 *	inserted or removed. The MMC layer will confirm that any
 *	present card is still functional, and initialize any newly
 *	inserted.
L
Linus Torvalds 已提交
1727
 */
1728
void mmc_detect_change(struct mmc_host *host, unsigned long delay)
L
Linus Torvalds 已提交
1729
{
1730
	_mmc_detect_change(host, delay, true);
L
Linus Torvalds 已提交
1731 1732 1733
}
EXPORT_SYMBOL(mmc_detect_change);

1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782
void mmc_init_erase(struct mmc_card *card)
{
	unsigned int sz;

	if (is_power_of_2(card->erase_size))
		card->erase_shift = ffs(card->erase_size) - 1;
	else
		card->erase_shift = 0;

	/*
	 * It is possible to erase an arbitrarily large area of an SD or MMC
	 * card.  That is not desirable because it can take a long time
	 * (minutes) potentially delaying more important I/O, and also the
	 * timeout calculations become increasingly hugely over-estimated.
	 * Consequently, 'pref_erase' is defined as a guide to limit erases
	 * to that size and alignment.
	 *
	 * For SD cards that define Allocation Unit size, limit erases to one
	 * Allocation Unit at a time.  For MMC cards that define High Capacity
	 * Erase Size, whether it is switched on or not, limit to that size.
	 * Otherwise just have a stab at a good value.  For modern cards it
	 * will end up being 4MiB.  Note that if the value is too small, it
	 * can end up taking longer to erase.
	 */
	if (mmc_card_sd(card) && card->ssr.au) {
		card->pref_erase = card->ssr.au;
		card->erase_shift = ffs(card->ssr.au) - 1;
	} else if (card->ext_csd.hc_erase_size) {
		card->pref_erase = card->ext_csd.hc_erase_size;
	} else {
		sz = (card->csd.capacity << (card->csd.read_blkbits - 9)) >> 11;
		if (sz < 128)
			card->pref_erase = 512 * 1024 / 512;
		else if (sz < 512)
			card->pref_erase = 1024 * 1024 / 512;
		else if (sz < 1024)
			card->pref_erase = 2 * 1024 * 1024 / 512;
		else
			card->pref_erase = 4 * 1024 * 1024 / 512;
		if (card->pref_erase < card->erase_size)
			card->pref_erase = card->erase_size;
		else {
			sz = card->pref_erase % card->erase_size;
			if (sz)
				card->pref_erase += card->erase_size - sz;
		}
	}
}

1783 1784
static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card,
				          unsigned int arg, unsigned int qty)
1785 1786 1787
{
	unsigned int erase_timeout;

1788 1789 1790 1791
	if (arg == MMC_DISCARD_ARG ||
	    (arg == MMC_TRIM_ARG && card->ext_csd.rev >= 6)) {
		erase_timeout = card->ext_csd.trim_timeout;
	} else if (card->ext_csd.erase_group_def & 1) {
1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814
		/* High Capacity Erase Group Size uses HC timeouts */
		if (arg == MMC_TRIM_ARG)
			erase_timeout = card->ext_csd.trim_timeout;
		else
			erase_timeout = card->ext_csd.hc_erase_timeout;
	} else {
		/* CSD Erase Group Size uses write timeout */
		unsigned int mult = (10 << card->csd.r2w_factor);
		unsigned int timeout_clks = card->csd.tacc_clks * mult;
		unsigned int timeout_us;

		/* Avoid overflow: e.g. tacc_ns=80000000 mult=1280 */
		if (card->csd.tacc_ns < 1000000)
			timeout_us = (card->csd.tacc_ns * mult) / 1000;
		else
			timeout_us = (card->csd.tacc_ns / 1000) * mult;

		/*
		 * ios.clock is only a target.  The real clock rate might be
		 * less but not that much less, so fudge it by multiplying by 2.
		 */
		timeout_clks <<= 1;
		timeout_us += (timeout_clks * 1000) /
1815
			      (mmc_host_clk_rate(card->host) / 1000);
1816 1817 1818 1819 1820 1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1833 1834 1835 1836 1837 1838 1839 1840 1841 1842 1843

		erase_timeout = timeout_us / 1000;

		/*
		 * Theoretically, the calculation could underflow so round up
		 * to 1ms in that case.
		 */
		if (!erase_timeout)
			erase_timeout = 1;
	}

	/* Multiplier for secure operations */
	if (arg & MMC_SECURE_ARGS) {
		if (arg == MMC_SECURE_ERASE_ARG)
			erase_timeout *= card->ext_csd.sec_erase_mult;
		else
			erase_timeout *= card->ext_csd.sec_trim_mult;
	}

	erase_timeout *= qty;

	/*
	 * Ensure at least a 1 second timeout for SPI as per
	 * 'mmc_set_data_timeout()'
	 */
	if (mmc_host_is_spi(card->host) && erase_timeout < 1000)
		erase_timeout = 1000;

1844
	return erase_timeout;
1845 1846
}

1847 1848 1849
static unsigned int mmc_sd_erase_timeout(struct mmc_card *card,
					 unsigned int arg,
					 unsigned int qty)
1850
{
1851 1852
	unsigned int erase_timeout;

1853 1854
	if (card->ssr.erase_timeout) {
		/* Erase timeout specified in SD Status Register (SSR) */
1855 1856
		erase_timeout = card->ssr.erase_timeout * qty +
				card->ssr.erase_offset;
1857 1858 1859 1860 1861
	} else {
		/*
		 * Erase timeout not specified in SD Status Register (SSR) so
		 * use 250ms per write block.
		 */
1862
		erase_timeout = 250 * qty;
1863 1864 1865
	}

	/* Must not be less than 1 second */
1866 1867 1868 1869
	if (erase_timeout < 1000)
		erase_timeout = 1000;

	return erase_timeout;
1870 1871
}

1872 1873 1874
static unsigned int mmc_erase_timeout(struct mmc_card *card,
				      unsigned int arg,
				      unsigned int qty)
1875 1876
{
	if (mmc_card_sd(card))
1877
		return mmc_sd_erase_timeout(card, arg, qty);
1878
	else
1879
		return mmc_mmc_erase_timeout(card, arg, qty);
1880 1881 1882 1883 1884
}

static int mmc_do_erase(struct mmc_card *card, unsigned int from,
			unsigned int to, unsigned int arg)
{
1885
	struct mmc_command cmd = {0};
1886
	unsigned int qty = 0;
1887
	unsigned long timeout;
1888 1889 1890 1891 1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927
	int err;

	/*
	 * qty is used to calculate the erase timeout which depends on how many
	 * erase groups (or allocation units in SD terminology) are affected.
	 * We count erasing part of an erase group as one erase group.
	 * For SD, the allocation units are always a power of 2.  For MMC, the
	 * erase group size is almost certainly also power of 2, but it does not
	 * seem to insist on that in the JEDEC standard, so we fall back to
	 * division in that case.  SD may not specify an allocation unit size,
	 * in which case the timeout is based on the number of write blocks.
	 *
	 * Note that the timeout for secure trim 2 will only be correct if the
	 * number of erase groups specified is the same as the total of all
	 * preceding secure trim 1 commands.  Since the power may have been
	 * lost since the secure trim 1 commands occurred, it is generally
	 * impossible to calculate the secure trim 2 timeout correctly.
	 */
	if (card->erase_shift)
		qty += ((to >> card->erase_shift) -
			(from >> card->erase_shift)) + 1;
	else if (mmc_card_sd(card))
		qty += to - from + 1;
	else
		qty += ((to / card->erase_size) -
			(from / card->erase_size)) + 1;

	if (!mmc_card_blockaddr(card)) {
		from <<= 9;
		to <<= 9;
	}

	if (mmc_card_sd(card))
		cmd.opcode = SD_ERASE_WR_BLK_START;
	else
		cmd.opcode = MMC_ERASE_GROUP_START;
	cmd.arg = from;
	cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
	err = mmc_wait_for_cmd(card->host, &cmd, 0);
	if (err) {
1928
		pr_err("mmc_erase: group start error %d, "
1929
		       "status %#x\n", err, cmd.resp[0]);
1930
		err = -EIO;
1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942
		goto out;
	}

	memset(&cmd, 0, sizeof(struct mmc_command));
	if (mmc_card_sd(card))
		cmd.opcode = SD_ERASE_WR_BLK_END;
	else
		cmd.opcode = MMC_ERASE_GROUP_END;
	cmd.arg = to;
	cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
	err = mmc_wait_for_cmd(card->host, &cmd, 0);
	if (err) {
1943
		pr_err("mmc_erase: group end error %d, status %#x\n",
1944
		       err, cmd.resp[0]);
1945
		err = -EIO;
1946 1947 1948 1949 1950 1951 1952
		goto out;
	}

	memset(&cmd, 0, sizeof(struct mmc_command));
	cmd.opcode = MMC_ERASE;
	cmd.arg = arg;
	cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
1953
	cmd.cmd_timeout_ms = mmc_erase_timeout(card, arg, qty);
1954 1955
	err = mmc_wait_for_cmd(card->host, &cmd, 0);
	if (err) {
1956
		pr_err("mmc_erase: erase error %d, status %#x\n",
1957 1958 1959 1960 1961 1962 1963 1964
		       err, cmd.resp[0]);
		err = -EIO;
		goto out;
	}

	if (mmc_host_is_spi(card->host))
		goto out;

1965
	timeout = jiffies + msecs_to_jiffies(MMC_CORE_TIMEOUT_MS);
1966 1967 1968 1969 1970 1971 1972 1973
	do {
		memset(&cmd, 0, sizeof(struct mmc_command));
		cmd.opcode = MMC_SEND_STATUS;
		cmd.arg = card->rca << 16;
		cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
		/* Do not retry else we can't see errors */
		err = mmc_wait_for_cmd(card->host, &cmd, 0);
		if (err || (cmd.resp[0] & 0xFDF92000)) {
1974
			pr_err("error %d requesting status %#x\n",
1975 1976 1977 1978
				err, cmd.resp[0]);
			err = -EIO;
			goto out;
		}
1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989

		/* Timeout if the device never becomes ready for data and
		 * never leaves the program state.
		 */
		if (time_after(jiffies, timeout)) {
			pr_err("%s: Card stuck in programming state! %s\n",
				mmc_hostname(card->host), __func__);
			err =  -EIO;
			goto out;
		}

1990
	} while (!(cmd.resp[0] & R1_READY_FOR_DATA) ||
1991
		 (R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG));
1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 2044 2045 2046 2047 2048 2049 2050 2051 2052 2053 2054 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066 2067 2068 2069 2070 2071 2072 2073 2074 2075 2076 2077 2078 2079
out:
	return err;
}

/**
 * mmc_erase - erase sectors.
 * @card: card to erase
 * @from: first sector to erase
 * @nr: number of sectors to erase
 * @arg: erase command argument (SD supports only %MMC_ERASE_ARG)
 *
 * Caller must claim host before calling this function.
 */
int mmc_erase(struct mmc_card *card, unsigned int from, unsigned int nr,
	      unsigned int arg)
{
	unsigned int rem, to = from + nr;

	if (!(card->host->caps & MMC_CAP_ERASE) ||
	    !(card->csd.cmdclass & CCC_ERASE))
		return -EOPNOTSUPP;

	if (!card->erase_size)
		return -EOPNOTSUPP;

	if (mmc_card_sd(card) && arg != MMC_ERASE_ARG)
		return -EOPNOTSUPP;

	if ((arg & MMC_SECURE_ARGS) &&
	    !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN))
		return -EOPNOTSUPP;

	if ((arg & MMC_TRIM_ARGS) &&
	    !(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN))
		return -EOPNOTSUPP;

	if (arg == MMC_SECURE_ERASE_ARG) {
		if (from % card->erase_size || nr % card->erase_size)
			return -EINVAL;
	}

	if (arg == MMC_ERASE_ARG) {
		rem = from % card->erase_size;
		if (rem) {
			rem = card->erase_size - rem;
			from += rem;
			if (nr > rem)
				nr -= rem;
			else
				return 0;
		}
		rem = nr % card->erase_size;
		if (rem)
			nr -= rem;
	}

	if (nr == 0)
		return 0;

	to = from + nr;

	if (to <= from)
		return -EINVAL;

	/* 'from' and 'to' are inclusive */
	to -= 1;

	return mmc_do_erase(card, from, to, arg);
}
EXPORT_SYMBOL(mmc_erase);

int mmc_can_erase(struct mmc_card *card)
{
	if ((card->host->caps & MMC_CAP_ERASE) &&
	    (card->csd.cmdclass & CCC_ERASE) && card->erase_size)
		return 1;
	return 0;
}
EXPORT_SYMBOL(mmc_can_erase);

int mmc_can_trim(struct mmc_card *card)
{
	if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN)
		return 1;
	return 0;
}
EXPORT_SYMBOL(mmc_can_trim);

2080 2081 2082 2083 2084 2085 2086 2087 2088 2089 2090 2091
int mmc_can_discard(struct mmc_card *card)
{
	/*
	 * As there's no way to detect the discard support bit at v4.5
	 * use the s/w feature support filed.
	 */
	if (card->ext_csd.feature_support & MMC_DISCARD_FEATURE)
		return 1;
	return 0;
}
EXPORT_SYMBOL(mmc_can_discard);

2092 2093
int mmc_can_sanitize(struct mmc_card *card)
{
2094 2095
	if (!mmc_can_trim(card) && !mmc_can_erase(card))
		return 0;
2096 2097 2098 2099 2100 2101
	if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_SANITIZE)
		return 1;
	return 0;
}
EXPORT_SYMBOL(mmc_can_sanitize);

2102 2103 2104 2105 2106 2107 2108 2109 2110 2111 2112 2113 2114 2115 2116 2117 2118 2119
int mmc_can_secure_erase_trim(struct mmc_card *card)
{
	if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN)
		return 1;
	return 0;
}
EXPORT_SYMBOL(mmc_can_secure_erase_trim);

int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from,
			    unsigned int nr)
{
	if (!card->erase_size)
		return 0;
	if (from % card->erase_size || nr % card->erase_size)
		return 0;
	return 1;
}
EXPORT_SYMBOL(mmc_erase_group_aligned);
L
Linus Torvalds 已提交
2120

2121 2122 2123 2124 2125 2126 2127 2128 2129 2130 2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141 2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152 2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163 2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174 2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185 2186 2187 2188 2189 2190 2191 2192 2193 2194 2195 2196
static unsigned int mmc_do_calc_max_discard(struct mmc_card *card,
					    unsigned int arg)
{
	struct mmc_host *host = card->host;
	unsigned int max_discard, x, y, qty = 0, max_qty, timeout;
	unsigned int last_timeout = 0;

	if (card->erase_shift)
		max_qty = UINT_MAX >> card->erase_shift;
	else if (mmc_card_sd(card))
		max_qty = UINT_MAX;
	else
		max_qty = UINT_MAX / card->erase_size;

	/* Find the largest qty with an OK timeout */
	do {
		y = 0;
		for (x = 1; x && x <= max_qty && max_qty - x >= qty; x <<= 1) {
			timeout = mmc_erase_timeout(card, arg, qty + x);
			if (timeout > host->max_discard_to)
				break;
			if (timeout < last_timeout)
				break;
			last_timeout = timeout;
			y = x;
		}
		qty += y;
	} while (y);

	if (!qty)
		return 0;

	if (qty == 1)
		return 1;

	/* Convert qty to sectors */
	if (card->erase_shift)
		max_discard = --qty << card->erase_shift;
	else if (mmc_card_sd(card))
		max_discard = qty;
	else
		max_discard = --qty * card->erase_size;

	return max_discard;
}

unsigned int mmc_calc_max_discard(struct mmc_card *card)
{
	struct mmc_host *host = card->host;
	unsigned int max_discard, max_trim;

	if (!host->max_discard_to)
		return UINT_MAX;

	/*
	 * Without erase_group_def set, MMC erase timeout depends on clock
	 * frequence which can change.  In that case, the best choice is
	 * just the preferred erase size.
	 */
	if (mmc_card_mmc(card) && !(card->ext_csd.erase_group_def & 1))
		return card->pref_erase;

	max_discard = mmc_do_calc_max_discard(card, MMC_ERASE_ARG);
	if (mmc_can_trim(card)) {
		max_trim = mmc_do_calc_max_discard(card, MMC_TRIM_ARG);
		if (max_trim < max_discard)
			max_discard = max_trim;
	} else if (max_discard < card->erase_size) {
		max_discard = 0;
	}
	pr_debug("%s: calculated max. discard sectors %u for timeout %u ms\n",
		 mmc_hostname(host), max_discard, host->max_discard_to);
	return max_discard;
}
EXPORT_SYMBOL(mmc_calc_max_discard);

2197 2198
int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen)
{
2199
	struct mmc_command cmd = {0};
2200 2201 2202 2203 2204 2205 2206 2207 2208 2209 2210

	if (mmc_card_blockaddr(card) || mmc_card_ddr_mode(card))
		return 0;

	cmd.opcode = MMC_SET_BLOCKLEN;
	cmd.arg = blocklen;
	cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
	return mmc_wait_for_cmd(card->host, &cmd, 5);
}
EXPORT_SYMBOL(mmc_set_blocklen);

2211 2212 2213 2214 2215 2216 2217 2218 2219 2220 2221 2222 2223 2224
int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount,
			bool is_rel_write)
{
	struct mmc_command cmd = {0};

	cmd.opcode = MMC_SET_BLOCK_COUNT;
	cmd.arg = blockcount & 0x0000FFFF;
	if (is_rel_write)
		cmd.arg |= 1 << 31;
	cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
	return mmc_wait_for_cmd(card->host, &cmd, 5);
}
EXPORT_SYMBOL(mmc_set_blockcount);

2225 2226 2227 2228 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2258 2259 2260 2261 2262 2263 2264 2265 2266 2267 2268 2269 2270 2271 2272 2273 2274 2275 2276 2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287 2288 2289 2290 2291 2292 2293 2294 2295 2296 2297 2298 2299 2300 2301 2302 2303 2304 2305 2306 2307 2308 2309 2310 2311 2312
static void mmc_hw_reset_for_init(struct mmc_host *host)
{
	if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)
		return;
	mmc_host_clk_hold(host);
	host->ops->hw_reset(host);
	mmc_host_clk_release(host);
}

int mmc_can_reset(struct mmc_card *card)
{
	u8 rst_n_function;

	if (!mmc_card_mmc(card))
		return 0;
	rst_n_function = card->ext_csd.rst_n_function;
	if ((rst_n_function & EXT_CSD_RST_N_EN_MASK) != EXT_CSD_RST_N_ENABLED)
		return 0;
	return 1;
}
EXPORT_SYMBOL(mmc_can_reset);

static int mmc_do_hw_reset(struct mmc_host *host, int check)
{
	struct mmc_card *card = host->card;

	if (!host->bus_ops->power_restore)
		return -EOPNOTSUPP;

	if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)
		return -EOPNOTSUPP;

	if (!card)
		return -EINVAL;

	if (!mmc_can_reset(card))
		return -EOPNOTSUPP;

	mmc_host_clk_hold(host);
	mmc_set_clock(host, host->f_init);

	host->ops->hw_reset(host);

	/* If the reset has happened, then a status command will fail */
	if (check) {
		struct mmc_command cmd = {0};
		int err;

		cmd.opcode = MMC_SEND_STATUS;
		if (!mmc_host_is_spi(card->host))
			cmd.arg = card->rca << 16;
		cmd.flags = MMC_RSP_SPI_R2 | MMC_RSP_R1 | MMC_CMD_AC;
		err = mmc_wait_for_cmd(card->host, &cmd, 0);
		if (!err) {
			mmc_host_clk_release(host);
			return -ENOSYS;
		}
	}

	host->card->state &= ~(MMC_STATE_HIGHSPEED | MMC_STATE_HIGHSPEED_DDR);
	if (mmc_host_is_spi(host)) {
		host->ios.chip_select = MMC_CS_HIGH;
		host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
	} else {
		host->ios.chip_select = MMC_CS_DONTCARE;
		host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
	}
	host->ios.bus_width = MMC_BUS_WIDTH_1;
	host->ios.timing = MMC_TIMING_LEGACY;
	mmc_set_ios(host);

	mmc_host_clk_release(host);

	return host->bus_ops->power_restore(host);
}

int mmc_hw_reset(struct mmc_host *host)
{
	return mmc_do_hw_reset(host, 0);
}
EXPORT_SYMBOL(mmc_hw_reset);

int mmc_hw_reset_check(struct mmc_host *host)
{
	return mmc_do_hw_reset(host, 1);
}
EXPORT_SYMBOL(mmc_hw_reset_check);

2313 2314 2315 2316 2317 2318 2319 2320
static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
{
	host->f_init = freq;

#ifdef CONFIG_MMC_DEBUG
	pr_info("%s: %s: trying to init card at %u Hz\n",
		mmc_hostname(host), __func__, host->f_init);
#endif
2321
	mmc_power_up(host, host->ocr_avail);
2322

2323 2324 2325 2326 2327 2328
	/*
	 * Some eMMCs (with VCCQ always on) may not be reset after power up, so
	 * do a hardware reset if possible.
	 */
	mmc_hw_reset_for_init(host);

2329 2330 2331 2332 2333
	/*
	 * sdio_reset sends CMD52 to reset card.  Since we do not know
	 * if the card is being re-initialized, just send it.  CMD52
	 * should be ignored by SD/eMMC cards.
	 */
2334 2335 2336 2337 2338 2339 2340 2341 2342 2343 2344 2345 2346 2347 2348 2349 2350
	sdio_reset(host);
	mmc_go_idle(host);

	mmc_send_if_cond(host, host->ocr_avail);

	/* Order's important: probe SDIO, then SD, then MMC */
	if (!mmc_attach_sdio(host))
		return 0;
	if (!mmc_attach_sd(host))
		return 0;
	if (!mmc_attach_mmc(host))
		return 0;

	mmc_power_off(host);
	return -EIO;
}

2351 2352 2353 2354 2355 2356 2357 2358 2359 2360 2361
int _mmc_detect_card_removed(struct mmc_host *host)
{
	int ret;

	if ((host->caps & MMC_CAP_NONREMOVABLE) || !host->bus_ops->alive)
		return 0;

	if (!host->card || mmc_card_removed(host->card))
		return 1;

	ret = host->bus_ops->alive(host);
2362 2363 2364 2365 2366 2367 2368 2369 2370 2371 2372 2373 2374

	/*
	 * Card detect status and alive check may be out of sync if card is
	 * removed slowly, when card detect switch changes while card/slot
	 * pads are still contacted in hardware (refer to "SD Card Mechanical
	 * Addendum, Appendix C: Card Detection Switch"). So reschedule a
	 * detect work 200ms later for this case.
	 */
	if (!ret && host->ops->get_cd && !host->ops->get_cd(host)) {
		mmc_detect_change(host, msecs_to_jiffies(200));
		pr_debug("%s: card removed too slowly\n", mmc_hostname(host));
	}

2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385
	if (ret) {
		mmc_card_set_removed(host->card);
		pr_debug("%s: card remove detected\n", mmc_hostname(host));
	}

	return ret;
}

int mmc_detect_card_removed(struct mmc_host *host)
{
	struct mmc_card *card = host->card;
2386
	int ret;
2387 2388

	WARN_ON(!host->claimed);
2389 2390 2391 2392 2393

	if (!card)
		return 1;

	ret = mmc_card_removed(card);
2394 2395 2396 2397
	/*
	 * The card will be considered unchanged unless we have been asked to
	 * detect a change or host requires polling to provide card detection.
	 */
2398
	if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL))
2399
		return ret;
2400 2401

	host->detect_change = 0;
2402 2403
	if (!ret) {
		ret = _mmc_detect_card_removed(host);
2404
		if (ret && (host->caps & MMC_CAP_NEEDS_POLL)) {
2405 2406 2407 2408 2409
			/*
			 * Schedule a detect work as soon as possible to let a
			 * rescan handle the card removal.
			 */
			cancel_delayed_work(&host->detect);
2410
			_mmc_detect_change(host, 0, false);
2411 2412
		}
	}
2413

2414
	return ret;
2415 2416 2417
}
EXPORT_SYMBOL(mmc_detect_card_removed);

2418
void mmc_rescan(struct work_struct *work)
L
Linus Torvalds 已提交
2419
{
D
David Howells 已提交
2420 2421
	struct mmc_host *host =
		container_of(work, struct mmc_host, detect.work);
H
Hein Tibosch 已提交
2422
	int i;
2423

2424
	if (host->rescan_disable)
2425
		return;
L
Linus Torvalds 已提交
2426

2427 2428 2429 2430 2431
	/* If there is a non-removable card registered, only scan once */
	if ((host->caps & MMC_CAP_NONREMOVABLE) && host->rescan_entered)
		return;
	host->rescan_entered = 1;

P
Pierre Ossman 已提交
2432
	mmc_bus_get(host);
P
Pierre Ossman 已提交
2433

2434 2435 2436 2437 2438
	/*
	 * if there is a _removable_ card registered, check whether it is
	 * still present
	 */
	if (host->bus_ops && host->bus_ops->detect && !host->bus_dead
2439
	    && !(host->caps & MMC_CAP_NONREMOVABLE))
2440 2441
		host->bus_ops->detect(host);

2442 2443
	host->detect_change = 0;

2444 2445 2446 2447
	/*
	 * Let mmc_bus_put() free the bus/bus_ops if we've found that
	 * the card is no longer present.
	 */
2448 2449 2450 2451 2452
	mmc_bus_put(host);
	mmc_bus_get(host);

	/* if there still is a card present, stop here */
	if (host->bus_ops != NULL) {
P
Pierre Ossman 已提交
2453
		mmc_bus_put(host);
2454 2455
		goto out;
	}
L
Linus Torvalds 已提交
2456

2457 2458 2459 2460 2461
	/*
	 * Only we can add a new handler, so it's safe to
	 * release the lock here.
	 */
	mmc_bus_put(host);
L
Linus Torvalds 已提交
2462

2463 2464
	if (!(host->caps & MMC_CAP_NONREMOVABLE) && host->ops->get_cd &&
			host->ops->get_cd(host) == 0) {
2465 2466 2467
		mmc_claim_host(host);
		mmc_power_off(host);
		mmc_release_host(host);
2468
		goto out;
2469
	}
L
Linus Torvalds 已提交
2470

2471
	mmc_claim_host(host);
H
Hein Tibosch 已提交
2472
	for (i = 0; i < ARRAY_SIZE(freqs); i++) {
2473 2474
		if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min)))
			break;
2475
		if (freqs[i] <= host->f_min)
2476
			break;
H
Hein Tibosch 已提交
2477
	}
2478 2479 2480
	mmc_release_host(host);

 out:
2481 2482
	if (host->caps & MMC_CAP_NEEDS_POLL)
		mmc_schedule_delayed_work(&host->detect, HZ);
L
Linus Torvalds 已提交
2483 2484
}

2485
void mmc_start_host(struct mmc_host *host)
L
Linus Torvalds 已提交
2486
{
2487
	host->f_init = max(freqs[0], host->f_min);
2488
	host->rescan_disable = 0;
2489 2490 2491
	if (host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP)
		mmc_power_off(host);
	else
2492
		mmc_power_up(host, host->ocr_avail);
2493
	_mmc_detect_change(host, 0, false);
L
Linus Torvalds 已提交
2494 2495
}

2496
void mmc_stop_host(struct mmc_host *host)
L
Linus Torvalds 已提交
2497
{
2498
#ifdef CONFIG_MMC_DEBUG
2499 2500
	unsigned long flags;
	spin_lock_irqsave(&host->lock, flags);
2501
	host->removed = 1;
2502
	spin_unlock_irqrestore(&host->lock, flags);
2503 2504
#endif

2505
	host->rescan_disable = 1;
2506
	cancel_delayed_work_sync(&host->detect);
2507 2508
	mmc_flush_scheduled_work();

2509 2510 2511
	/* clear pm flags now and let card drivers set them as needed */
	host->pm_flags = 0;

P
Pierre Ossman 已提交
2512 2513
	mmc_bus_get(host);
	if (host->bus_ops && !host->bus_dead) {
2514
		/* Calling bus_ops->remove() with a claimed host can deadlock */
2515
		host->bus_ops->remove(host);
P
Pierre Ossman 已提交
2516 2517
		mmc_claim_host(host);
		mmc_detach_bus(host);
2518
		mmc_power_off(host);
P
Pierre Ossman 已提交
2519
		mmc_release_host(host);
D
Denis Karpov 已提交
2520 2521
		mmc_bus_put(host);
		return;
L
Linus Torvalds 已提交
2522
	}
P
Pierre Ossman 已提交
2523 2524 2525
	mmc_bus_put(host);

	BUG_ON(host->card);
L
Linus Torvalds 已提交
2526 2527 2528 2529

	mmc_power_off(host);
}

2530
int mmc_power_save_host(struct mmc_host *host)
2531
{
2532 2533
	int ret = 0;

2534 2535 2536 2537
#ifdef CONFIG_MMC_DEBUG
	pr_info("%s: %s: powering down\n", mmc_hostname(host), __func__);
#endif

2538 2539 2540 2541
	mmc_bus_get(host);

	if (!host->bus_ops || host->bus_dead || !host->bus_ops->power_restore) {
		mmc_bus_put(host);
2542
		return -EINVAL;
2543 2544 2545
	}

	if (host->bus_ops->power_save)
2546
		ret = host->bus_ops->power_save(host);
2547 2548 2549 2550

	mmc_bus_put(host);

	mmc_power_off(host);
2551 2552

	return ret;
2553 2554 2555
}
EXPORT_SYMBOL(mmc_power_save_host);

2556
int mmc_power_restore_host(struct mmc_host *host)
2557
{
2558 2559
	int ret;

2560 2561 2562 2563
#ifdef CONFIG_MMC_DEBUG
	pr_info("%s: %s: powering up\n", mmc_hostname(host), __func__);
#endif

2564 2565 2566 2567
	mmc_bus_get(host);

	if (!host->bus_ops || host->bus_dead || !host->bus_ops->power_restore) {
		mmc_bus_put(host);
2568
		return -EINVAL;
2569 2570
	}

2571
	mmc_power_up(host, host->card->ocr);
2572
	ret = host->bus_ops->power_restore(host);
2573 2574

	mmc_bus_put(host);
2575 2576

	return ret;
2577 2578 2579
}
EXPORT_SYMBOL(mmc_power_restore_host);

2580 2581 2582 2583 2584 2585 2586 2587 2588 2589 2590 2591 2592 2593 2594 2595 2596 2597 2598 2599 2600 2601 2602 2603 2604 2605 2606 2607 2608
/*
 * Flush the cache to the non-volatile storage.
 */
int mmc_flush_cache(struct mmc_card *card)
{
	struct mmc_host *host = card->host;
	int err = 0;

	if (!(host->caps2 & MMC_CAP2_CACHE_CTRL))
		return err;

	if (mmc_card_mmc(card) &&
			(card->ext_csd.cache_size > 0) &&
			(card->ext_csd.cache_ctrl & 1)) {
		err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
				EXT_CSD_FLUSH_CACHE, 1, 0);
		if (err)
			pr_err("%s: cache flush error %d\n",
					mmc_hostname(card->host), err);
	}

	return err;
}
EXPORT_SYMBOL(mmc_flush_cache);

/*
 * Turn the cache ON/OFF.
 * Turning the cache OFF shall trigger flushing of the data
 * to the non-volatile storage.
2609
 * This function should be called with host claimed
2610 2611 2612 2613
 */
int mmc_cache_ctrl(struct mmc_host *host, u8 enable)
{
	struct mmc_card *card = host->card;
2614
	unsigned int timeout;
2615 2616 2617 2618 2619 2620 2621 2622 2623 2624
	int err = 0;

	if (!(host->caps2 & MMC_CAP2_CACHE_CTRL) ||
			mmc_card_is_removable(host))
		return err;

	if (card && mmc_card_mmc(card) &&
			(card->ext_csd.cache_size > 0)) {
		enable = !!enable;

2625 2626
		if (card->ext_csd.cache_ctrl ^ enable) {
			timeout = enable ? card->ext_csd.generic_cmd6_time : 0;
2627
			err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
2628 2629 2630 2631 2632 2633 2634 2635 2636
					EXT_CSD_CACHE_CTRL, enable, timeout);
			if (err)
				pr_err("%s: cache %s error %d\n",
						mmc_hostname(card->host),
						enable ? "on" : "off",
						err);
			else
				card->ext_csd.cache_ctrl = enable;
		}
2637 2638 2639 2640 2641 2642
	}

	return err;
}
EXPORT_SYMBOL(mmc_cache_ctrl);

L
Linus Torvalds 已提交
2643 2644
#ifdef CONFIG_PM

2645 2646 2647 2648 2649 2650 2651 2652 2653 2654
/* Do the card removal on suspend if card is assumed removeable
 * Do that in pm notifier while userspace isn't yet frozen, so we will be able
   to sync the card.
*/
int mmc_pm_notify(struct notifier_block *notify_block,
					unsigned long mode, void *unused)
{
	struct mmc_host *host = container_of(
		notify_block, struct mmc_host, pm_notify);
	unsigned long flags;
2655
	int err = 0;
2656 2657 2658 2659 2660 2661 2662 2663 2664

	switch (mode) {
	case PM_HIBERNATION_PREPARE:
	case PM_SUSPEND_PREPARE:
		spin_lock_irqsave(&host->lock, flags);
		host->rescan_disable = 1;
		spin_unlock_irqrestore(&host->lock, flags);
		cancel_delayed_work_sync(&host->detect);

2665 2666 2667 2668 2669 2670 2671
		if (!host->bus_ops)
			break;

		/* Validate prerequisites for suspend */
		if (host->bus_ops->pre_suspend)
			err = host->bus_ops->pre_suspend(host);
		if (!err && host->bus_ops->suspend)
2672 2673
			break;

2674
		/* Calling bus_ops->remove() with a claimed host can deadlock */
2675
		host->bus_ops->remove(host);
2676
		mmc_claim_host(host);
2677
		mmc_detach_bus(host);
2678
		mmc_power_off(host);
2679 2680 2681 2682 2683 2684
		mmc_release_host(host);
		host->pm_flags = 0;
		break;

	case PM_POST_SUSPEND:
	case PM_POST_HIBERNATION:
2685
	case PM_POST_RESTORE:
2686 2687 2688 2689

		spin_lock_irqsave(&host->lock, flags);
		host->rescan_disable = 0;
		spin_unlock_irqrestore(&host->lock, flags);
2690
		_mmc_detect_change(host, 0, false);
2691 2692 2693 2694 2695

	}

	return 0;
}
L
Linus Torvalds 已提交
2696 2697
#endif

2698 2699 2700 2701 2702 2703 2704 2705 2706 2707 2708 2709 2710 2711 2712 2713 2714
/**
 * mmc_init_context_info() - init synchronization context
 * @host: mmc host
 *
 * Init struct context_info needed to implement asynchronous
 * request mechanism, used by mmc core, host driver and mmc requests
 * supplier.
 */
void mmc_init_context_info(struct mmc_host *host)
{
	spin_lock_init(&host->context_info.lock);
	host->context_info.is_new_req = false;
	host->context_info.is_done_rcv = false;
	host->context_info.is_waiting_last_req = false;
	init_waitqueue_head(&host->context_info.wait);
}

2715 2716 2717 2718
static int __init mmc_init(void)
{
	int ret;

T
Tejun Heo 已提交
2719
	workqueue = alloc_ordered_workqueue("kmmcd", 0);
2720 2721 2722 2723
	if (!workqueue)
		return -ENOMEM;

	ret = mmc_register_bus();
P
Pierre Ossman 已提交
2724 2725 2726 2727 2728 2729 2730 2731 2732 2733 2734 2735 2736 2737 2738 2739 2740 2741 2742 2743
	if (ret)
		goto destroy_workqueue;

	ret = mmc_register_host_class();
	if (ret)
		goto unregister_bus;

	ret = sdio_register_bus();
	if (ret)
		goto unregister_host_class;

	return 0;

unregister_host_class:
	mmc_unregister_host_class();
unregister_bus:
	mmc_unregister_bus();
destroy_workqueue:
	destroy_workqueue(workqueue);

2744 2745 2746 2747 2748
	return ret;
}

static void __exit mmc_exit(void)
{
P
Pierre Ossman 已提交
2749
	sdio_unregister_bus();
2750 2751 2752 2753 2754
	mmc_unregister_host_class();
	mmc_unregister_bus();
	destroy_workqueue(workqueue);
}

2755
subsys_initcall(mmc_init);
2756 2757
module_exit(mmc_exit);

L
Linus Torvalds 已提交
2758
MODULE_LICENSE("GPL");