Kconfig 18.3 KB
Newer Older
1 2 3 4 5 6 7
config LEDS_GPIO_REGISTER
	bool
	help
	  This option provides the function gpio_led_register_device.
	  As this function is used by arch code it must not be compiled as a
	  module.

8
menuconfig NEW_LEDS
R
Richard Purdie 已提交
9 10
	bool "LED Support"
	help
11 12 13
	  Say Y to enable Linux LED support.  This allows control of supported
	  LEDs from both userspace and optionally, by kernel events (triggers).

14 15
if NEW_LEDS

R
Richard Purdie 已提交
16
config LEDS_CLASS
17
	tristate "LED Class Support"
R
Richard Purdie 已提交
18 19 20 21
	help
	  This option enables the led sysfs class in /sys/class/leds.  You'll
	  need this to do anything useful with LEDs.  If unsure, say N.

22 23 24 25 26 27 28 29 30 31
config LEDS_CLASS_FLASH
	tristate "LED Flash Class Support"
	depends on LEDS_CLASS
	help
	  This option enables the flash led sysfs class in /sys/class/leds.
	  It wrapps LED Class and adds flash LEDs specific sysfs attributes
	  and kernel internal API to it. You'll need this to provide support
	  for the flash related features of a LED device. It can be built
	  as a module.

B
Ben Dooks 已提交
32
comment "LED drivers"
33

H
Haojian Zhuang 已提交
34 35
config LEDS_88PM860X
	tristate "LED Support for Marvell 88PM860x PMIC"
J
Johannes Berg 已提交
36
	depends on LEDS_CLASS
R
Richard Purdie 已提交
37
	depends on MFD_88PM860X
H
Haojian Zhuang 已提交
38 39 40 41
	help
	  This option enables support for on-chip LED drivers found on Marvell
	  Semiconductor 88PM8606 PMIC.

42 43 44
config LEDS_AAT1290
	tristate "LED support for the AAT1290"
	depends on LEDS_CLASS_FLASH
R
Randy Dunlap 已提交
45
	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
46
	depends on GPIOLIB || COMPILE_TEST
47
	depends on OF
48
	depends on PINCTRL
49 50 51
	help
	 This option enables support for the LEDs on the AAT1290.

52 53 54 55 56 57 58 59
config LEDS_BCM6328
	tristate "LED Support for Broadcom BCM6328"
	depends on LEDS_CLASS
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6328
	  LED HW controller accessed via MMIO registers.

60 61 62 63 64 65 66 67
config LEDS_BCM6358
	tristate "LED Support for Broadcom BCM6358"
	depends on LEDS_CLASS
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6358
	  LED HW controller accessed via MMIO registers.

68 69 70 71 72 73 74 75 76 77
config LEDS_LM3530
	tristate "LCD Backlight driver for LM3530"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the LCD backlight using
	  LM3530 ambient light sensor chip. This ALS chip can be
	  controlled manually or using PWM input or using ambient
	  light automatically.

J
Johan Hovold 已提交
78 79 80 81 82 83 84 85 86 87 88 89 90
config LEDS_LM3533
	tristate "LED support for LM3533"
	depends on LEDS_CLASS
	depends on MFD_LM3533
	help
	  This option enables support for the LEDs on National Semiconductor /
	  TI LM3533 Lighting Power chips.

	  The LEDs can be controlled directly, through PWM input, or by the
	  ambient-light-sensor interface. The chip supports
	  hardware-accelerated blinking with maximum on and off periods of 9.8
	  and 77 seconds respectively.

91 92 93 94 95 96 97 98 99 100 101
config LEDS_LM3642
	tristate "LED support for LM3642 Chip"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to LM3642.
	  The LM3642 is a 4MHz fixed-frequency synchronous boost
	  converter plus 1.5A constant current driver for a high-current
	  white LED.


102 103
config LEDS_LOCOMO
	tristate "LED Support for Locomo device"
J
Johannes Berg 已提交
104
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
105
	depends on SHARP_LOCOMO
106 107 108 109
	help
	  This option enables support for the LEDs on Sharp Locomo.
	  Zaurus models SL-5500 and SL-5600.

110 111
config LEDS_MIKROTIK_RB532
	tristate "LED Support for Mikrotik Routerboard 532"
J
Johannes Berg 已提交
112
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
113
	depends on MIKROTIK_RB532
114 115 116 117
	help
	  This option enables support for the so called "User LED" of
	  Mikrotik's Routerboard 532.

B
Ben Dooks 已提交
118 119
config LEDS_S3C24XX
	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
J
Johannes Berg 已提交
120
	depends on LEDS_CLASS
121
	depends on ARCH_S3C24XX
B
Ben Dooks 已提交
122 123 124 125
	help
	  This option enables support for LEDs connected to GPIO lines
	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.

126 127
config LEDS_NET48XX
	tristate "LED Support for Soekris net48xx series Error LED"
J
Johannes Berg 已提交
128
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
129
	depends on SCx200_GPIO
130 131 132 133
	help
	  This option enables support for the Soekris net4801 and net4826 error
	  LED.

134 135
config LEDS_FSG
	tristate "LED Support for the Freecom FSG-3"
J
Johannes Berg 已提交
136
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
137
	depends on MACH_FSG
138 139 140
	help
	  This option enables support for the LEDs on the Freecom FSG-3.

141 142
config LEDS_WRAP
	tristate "LED Support for the WRAP series LEDs"
J
Johannes Berg 已提交
143
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
144
	depends on SCx200_GPIO
145 146 147
	help
	  This option enables support for the PCEngines WRAP programmable LEDs.

Y
Yoichi Yuasa 已提交
148 149
config LEDS_COBALT_QUBE
	tristate "LED Support for the Cobalt Qube series front LED"
J
Johannes Berg 已提交
150
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
151
	depends on MIPS_COBALT
152
	help
Y
Yoichi Yuasa 已提交
153
	  This option enables support for the front LED on Cobalt Qube series
154

155 156
config LEDS_COBALT_RAQ
	bool "LED Support for the Cobalt Raq series"
157
	depends on LEDS_CLASS=y && MIPS_COBALT
158 159 160 161
	select LEDS_TRIGGERS
	help
	  This option enables support for the Cobalt Raq series LEDs.

162 163
config LEDS_SUNFIRE
	tristate "LED support for SunFire servers."
J
Johannes Berg 已提交
164
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
165
	depends on SPARC64
166 167 168 169 170
	select LEDS_TRIGGERS
	help
	  This option enables support for the Left, Middle, and Right
	  LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.

171 172
config LEDS_IPAQ_MICRO
	tristate "LED Support for the Compaq iPAQ h3xxx"
173
	depends on LEDS_CLASS
174 175 176 177 178
	depends on MFD_IPAQ_MICRO
	help
	  Choose this option if you want to use the notification LED on
	  Compaq/HP iPAQ h3100 and h3600.

179 180
config LEDS_HP6XX
	tristate "LED Support for the HP Jornada 6xx"
J
Johannes Berg 已提交
181
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
182
	depends on SH_HP6XX
183
	help
184
	  This option enables LED support for the handheld
185 186
	  HP Jornada 620/660/680/690.

R
Riku Voipio 已提交
187 188
config LEDS_PCA9532
	tristate "LED driver for PCA9532 dimmer"
J
Johannes Berg 已提交
189
	depends on LEDS_CLASS
190
	depends on I2C && INPUT
R
Riku Voipio 已提交
191 192
	help
	  This option enables support for NXP pca9532
193
	  LED controller. It is generally only useful
R
Riku Voipio 已提交
194 195
	  as a platform driver

196 197 198 199 200 201 202 203 204 205
config LEDS_PCA9532_GPIO
	bool "Enable GPIO support for PCA9532"
	depends on LEDS_PCA9532
	depends on GPIOLIB
	help
	  Allow unused pins on PCA9532 to be used as gpio.

	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
	  set to PCA9532_TYPE_GPIO.

206 207
config LEDS_GPIO
	tristate "LED Support for GPIO connected LEDs"
J
Johannes Berg 已提交
208
	depends on LEDS_CLASS
209
	depends on GPIOLIB || COMPILE_TEST
210 211 212
	help
	  This option enables support for the LEDs connected to GPIO
	  outputs. To be useful the particular board must have LEDs
213 214 215 216
	  and they must be connected to the GPIO lines.  The LEDs must be
	  defined as platform devices and/or OpenFirmware platform devices.
	  The code to use these bindings can be selected below.

217 218
config LEDS_LP3944
	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
J
Johannes Berg 已提交
219
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
220
	depends on I2C
221
	help
222 223 224
	  This option enables support for LEDs connected to the National
	  Semiconductor LP3944 Lighting Management Unit (LMU) also known as
	  Fun Light Chip.
225 226 227 228

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp3944.

229
config LEDS_LP55XX_COMMON
230 231
	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
	depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
232
	select FW_LOADER
233
	select FW_LOADER_USER_HELPER
234
	help
235
	  This option supports common operations for LP5521/5523/55231/5562/8501
236 237
	  devices.

238 239 240
config LEDS_LP5521
	tristate "LED Support for N.S. LP5521 LED driver chip"
	depends on LEDS_CLASS && I2C
241
	select LEDS_LP55XX_COMMON
242 243 244 245 246 247 248
	help
	  If you say yes here you get support for the National Semiconductor
	  LP5521 LED driver. It is 3 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

config LEDS_LP5523
249
	tristate "LED Support for TI/National LP5523/55231 LED driver chip"
250
	depends on LEDS_CLASS && I2C
251
	select LEDS_LP55XX_COMMON
252
	help
253 254 255
	  If you say yes here you get support for TI/National Semiconductor
	  LP5523/55231 LED driver.
	  It is 9 channel chip with programmable engines.
256 257 258
	  Driver provides direct control via LED class and interface for
	  programming the engines.

K
Kim, Milo 已提交
259 260 261 262 263 264 265 266 267 268
config LEDS_LP5562
	tristate "LED Support for TI LP5562 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP5562 LED driver.
	  It is 4 channels chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

269 270 271 272 273 274 275 276 277 278 279 280
config LEDS_LP8501
	tristate "LED Support for TI LP8501 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP8501 LED driver.
	  It is 9 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.
	  It is similar as LP5523, but output power selection is available.
	  And register layout and engine program schemes are different.

K
Kim, Milo 已提交
281 282 283 284 285 286 287
config LEDS_LP8788
	tristate "LED support for the TI LP8788 PMIC"
	depends on LEDS_CLASS
	depends on MFD_LP8788
	help
	  This option enables support for the Keyboard LEDs on the LP8788 PMIC.

288 289
config LEDS_LP8860
	tristate "LED support for the TI LP8860 4 channel LED driver"
A
Axel Lin 已提交
290 291
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
292 293 294 295 296 297 298
	help
	  If you say yes here you get support for the TI LP8860 4 channel
	  LED driver.
	  This option enables support for the display cluster LEDs
	  on the LP8860 4 channel LED driver using the I2C communication
	  bus.

299
config LEDS_CLEVO_MAIL
300
	tristate "Mail LED on Clevo notebook"
J
Johannes Berg 已提交
301
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
302
	depends on X86 && SERIO_I8042 && DMI
303 304 305 306 307
	help
	  This driver makes the mail LED accessible from userspace
	  programs through the leds subsystem. This LED have three
	  known mode: off, blink at 0.5Hz and blink at 1Hz.

308 309 310 311 312
	  The driver supports two kinds of interface: using ledtrig-timer
	  or through /sys/class/leds/clevo::mail/brightness. As this LED
	  cannot change it's brightness it blinks instead. The brightness
	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
	  blink at 1Hz.
313 314 315

	  This module can drive the mail LED for the following notebooks:

316
	  	Clevo D400P
317 318 319 320 321 322 323
	  	Clevo D410J
	  	Clevo D410V
	  	Clevo D400V/D470V (not tested, but might work)
	  	Clevo M540N
	  	Clevo M5x0N (not tested, but might work)
	  	Positivo Mobile (Clevo M5x0V)

324
	  If your model is not listed here you can try the "nodetect"
325
	  module parameter.
326

327 328 329
	  To compile this driver as a module, choose M here: the
	  module will be called leds-clevo-mail.

330 331
config LEDS_PCA955X
	tristate "LED Support for PCA955x I2C chips"
J
Johannes Berg 已提交
332
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
333
	depends on I2C
334 335 336 337 338
	help
	  This option enables support for LEDs connected to PCA955x
	  LED driver chips accessed via the I2C bus.  Supported
	  devices include PCA9550, PCA9551, PCA9552, and PCA9553.

339
config LEDS_PCA963X
340
	tristate "LED support for PCA963x I2C chip"
341 342 343
	depends on LEDS_CLASS
	depends on I2C
	help
344 345 346
	  This option enables support for LEDs connected to the PCA963x
	  LED driver chip accessed via the I2C bus. Supported
	  devices include PCA9633 and PCA9634
347

M
Mark Brown 已提交
348 349
config LEDS_WM831X_STATUS
	tristate "LED support for status LEDs on WM831x PMICs"
J
Johannes Berg 已提交
350
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
351
	depends on MFD_WM831X
M
Mark Brown 已提交
352 353 354 355
	help
	  This option enables support for the status LEDs of the WM831x
          series of PMICs.

M
Mark Brown 已提交
356 357
config LEDS_WM8350
	tristate "LED Support for WM8350 AudioPlus PMIC"
J
Johannes Berg 已提交
358
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
359
	depends on MFD_WM8350
M
Mark Brown 已提交
360 361 362 363
	help
	  This option enables support for LEDs driven by the Wolfson
	  Microelectronics WM8350 AudioPlus PMIC.

364 365
config LEDS_DA903X
	tristate "LED Support for DA9030/DA9034 PMIC"
J
Johannes Berg 已提交
366
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
367
	depends on PMIC_DA903X
368 369 370 371
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9030/DA9034 PMICs.

372 373 374 375 376 377 378 379
config LEDS_DA9052
	tristate "Dialog DA9052/DA9053 LEDS"
	depends on LEDS_CLASS
	depends on PMIC_DA9052
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.

380 381
config LEDS_DAC124S085
	tristate "LED Support for DAC124S085 SPI DAC"
J
Johannes Berg 已提交
382
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
383
	depends on SPI
384 385 386 387
	help
	  This option enables support for DAC124S085 SPI DAC from NatSemi,
	  which can be used to control up to four LEDs.

388 389
config LEDS_PWM
	tristate "PWM driven LED Support"
J
Johannes Berg 已提交
390
	depends on LEDS_CLASS
391
	depends on PWM
392 393 394
	help
	  This option enables support for pwm driven LEDs

395 396
config LEDS_REGULATOR
	tristate "REGULATOR driven LED support"
J
Johannes Berg 已提交
397
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
398
	depends on REGULATOR
399 400 401
	help
	  This option enables support for regulator driven LEDs.

K
Kim Kyuwon 已提交
402 403
config LEDS_BD2802
	tristate "LED driver for BD2802 RGB LED"
J
Johannes Berg 已提交
404
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
405
	depends on I2C
K
Kim Kyuwon 已提交
406 407 408 409
	help
	  This option enables support for BD2802GU RGB LED driver chips
	  accessed via the I2C bus.

410 411
config LEDS_INTEL_SS4200
	tristate "LED driver for Intel NAS SS4200 series"
J
Johannes Berg 已提交
412
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
413
	depends on PCI && DMI
414 415 416 417 418 419
	help
	  This option enables support for the Intel SS4200 series of
	  Network Attached Storage servers.  You may control the hard
	  drive or power LEDs on the front panel.  Using this driver
	  can stop the front LED from blinking after startup.

420 421
config LEDS_LT3593
	tristate "LED driver for LT3593 controllers"
J
Johannes Berg 已提交
422
	depends on LEDS_CLASS
423
	depends on GPIOLIB || COMPILE_TEST
424 425 426 427 428
	help
	  This option enables support for LEDs driven by a Linear Technology
	  LT3593 controller. This controller uses a special one-wire pulse
	  coding protocol to set the brightness.

429 430
config LEDS_ADP5520
	tristate "LED Support for ADP5520/ADP5501 PMIC"
J
Johannes Berg 已提交
431
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
432
	depends on PMIC_ADP5520
433 434 435 436 437 438 439
	help
	  This option enables support for on-chip LED drivers found
	  on Analog Devices ADP5520/ADP5501 PMICs.

	  To compile this driver as a module, choose M here: the module will
	  be called leds-adp5520.

440 441
config LEDS_DELL_NETBOOKS
	tristate "External LED on Dell Business Netbooks"
J
Johannes Berg 已提交
442
	depends on LEDS_CLASS
443 444 445 446 447
	depends on X86 && ACPI_WMI
	help
	  This adds support for the Latitude 2100 and similar
	  notebooks that have an external LED.

448
config LEDS_MC13783
449
	tristate "LED Support for MC13XXX PMIC"
J
Johannes Berg 已提交
450
	depends on LEDS_CLASS
451
	depends on MFD_MC13XXX
452 453
	help
	  This option enable support for on-chip LED drivers found
454
	  on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
455

456 457
config LEDS_NS2
	tristate "LED support for Network Space v2 GPIO LEDs"
J
Johannes Berg 已提交
458
	depends on LEDS_CLASS
459
	depends on MACH_KIRKWOOD || MACH_ARMADA_370
460 461
	default y
	help
462 463 464 465 466 467 468
	  This option enables support for the dual-GPIO LEDs found on the
	  following LaCie/Seagate boards:

		Network Space v2 (and parents: Max, Mini)
		Internet Space v2
		d2 Network v2
		n090401 (Seagate NAS 4-Bay)
469

470 471
config LEDS_NETXBIG
	tristate "LED support for Big Network series LEDs"
472
	depends on LEDS_CLASS
473
	depends on MACH_KIRKWOOD
474 475 476 477 478 479
	default y
	help
	  This option enable support for LEDs found on the LaCie 2Big
	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
	  controlled through a GPIO extension bus.

P
Paul Parsons 已提交
480 481
config LEDS_ASIC3
	bool "LED support for the HTC ASIC3"
482
	depends on LEDS_CLASS=y
P
Paul Parsons 已提交
483 484 485 486 487 488 489 490
	depends on MFD_ASIC3
	default y
	help
	  This option enables support for the LEDs on the HTC ASIC3. The HTC
	  ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
	  cannot be used. This driver supports hardware blinking with an on+off
	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.

491 492 493 494 495 496 497 498
config LEDS_TCA6507
	tristate "LED Support for TCA6507 I2C chip"
	depends on LEDS_CLASS && I2C
	help
	  This option enables support for LEDs connected to TC6507
	  LED driver chips accessed via the I2C bus.
	  Driver support brightness control and hardware-assisted blinking.

499 500 501 502 503 504 505 506
config LEDS_TLC591XX
	tristate "LED driver for TLC59108 and TLC59116 controllers"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for Texas Instruments TLC59108
	  and TLC59116 LED controllers.

507 508 509
config LEDS_MAX77693
	tristate "LED support for MAX77693 Flash"
	depends on LEDS_CLASS_FLASH
510
	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
511 512 513 514 515 516 517
	depends on MFD_MAX77693
	depends on OF
	help
	  This option enables support for the flash part of the MAX77693
	  multifunction device. It has build in control for two leds in flash
	  and torch mode.

518 519 520 521 522 523 524
config LEDS_MAX8997
	tristate "LED support for MAX8997 PMIC"
	depends on LEDS_CLASS && MFD_MAX8997
	help
	  This option enables support for on-chip LED drivers on
	  MAXIM MAX8997 PMIC.

525 526
config LEDS_LM355x
	tristate "LED support for LM355x Chips, LM3554 and LM3556"
527 528 529
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
530 531
	  This option enables support for LEDs connected to LM355x.
	  LM355x includes Torch, Flash and Indicator functions.
532

533 534
config LEDS_OT200
	tristate "LED support for the Bachmann OT200"
J
Jean Delvare 已提交
535
	depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
536 537 538 539
	help
	  This option enables support for the LEDs on the Bachmann OT200.
	  Say Y to enable LEDs on the Bachmann OT200.

540 541 542 543 544 545 546 547 548
config LEDS_MENF21BMC
	tristate "LED support for the MEN 14F021P00 BMC"
	depends on LEDS_CLASS && MFD_MENF21BMC
	help
	  Say Y here to include support for the MEN 14F021P00 BMC LEDs.

	  This driver can also be built as a module. If so the module
	  will be called leds-menf21bmc.

I
Ingi Kim 已提交
549 550
config LEDS_KTD2692
	tristate "LED support for KTD2692 flash LED controller"
551 552
	depends on LEDS_CLASS_FLASH && OF
	depends on GPIOLIB || COMPILE_TEST
I
Ingi Kim 已提交
553 554 555 556 557 558
	help
	  This option enables support for KTD2692 LED flash connected
	  through ExpressWire interface.

	  Say Y to enable this driver.

559 560 561 562 563 564 565 566 567 568
config LEDS_SEAD3
	tristate "LED support for the MIPS SEAD 3 board"
	depends on LEDS_CLASS && MIPS_SEAD3
	help
	  Say Y here to include support for the FLED and PLED LEDs on SEAD3 eval
	  boards.

	  This driver can also be built as a module. If so the module
	  will be called leds-sead3.

569 570
comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"

571 572 573 574 575 576 577 578
config LEDS_BLINKM
	tristate "LED support for the BlinkM I2C RGB LED"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the BlinkM RGB LED connected
	  through I2C. Say Y to enable support for the BlinkM LED.

579 580 581 582 583 584 585 586 587 588 589
config LEDS_POWERNV
	tristate "LED support for PowerNV Platform"
	depends on LEDS_CLASS
	depends on PPC_POWERNV
	depends on OF
	help
	  This option enables support for the system LEDs present on
	  PowerNV platforms. Say 'y' to enable this support in kernel.
	  To compile this driver as a module, choose 'm' here: the module
	  will be called leds-powernv.

590 591 592 593 594 595 596 597 598 599
config LEDS_SYSCON
	bool "LED support for LEDs on system controllers"
	depends on LEDS_CLASS=y
	depends on MFD_SYSCON
	depends on OF
	help
	  This option enabled support for the LEDs on syscon type
	  devices. This will only work with device tree enabled
	  devices.

600
config LEDS_VERSATILE
601
	tristate "LED support for the ARM Versatile and RealView"
602 603 604 605 606 607
	depends on ARCH_REALVIEW || ARCH_VERSATILE
	depends on LEDS_CLASS
	help
	  This option enabled support for the LEDs on the ARM Versatile
	  and RealView boards. Say Y to enabled these.

H
H Hartley Sweeten 已提交
608
comment "LED Triggers"
609
source "drivers/leds/trigger/Kconfig"
610

611
endif # NEW_LEDS