Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.

On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.

The patch is inspired by commit 73333626 ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").
Signed-off-by: NTao Ren <taoren@fb.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull tracing fix from Steven Rostedt:
 "Masami found a slight bug in his code where he transposed the
  arguments of a call to strpbrk.

  The reason this wasn't detected in our tests is that the only way this
  would transpire is when a kprobe event with a symbol offset is
  attached to a function that belongs to a module that isn't loaded yet.
  When the kprobe trace event is added, the offset would be truncated
  after it was parsed, and when the module is loaded, it would use the
  symbol without the offset (as the nul character added by the parsing
  would not be replaced with the original character)"

* tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Fix strpbrk() argument order

Pull ARM fix from Russell King:
 "Ard spotted a typo in one of the assembly files which leads to a
  kernel oops when that code path is executed. Fix this"

* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm

Pull networking fixes from David Miller:

 1) Handle errors mid-stream of an all dump, from Alexey Kodanev.

 2) Fix build of openvswitch with certain combinations of netfilter
    options, from Arnd Bergmann.

 3) Fix interactions between GSO and BQL, from Eric Dumazet.

 4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
    Hoffstätte.

 5) S390 qeth driver fixes from Julian Wiedmann.

 6) Allow ipv6 link local addresses for netconsole when both source and
    destination are link local, from Matwey V. Kornilov.

 7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.

 8) Initialize mutex before use in dsa microchip driver, from Tristram
    Ha.

 9) Out-of-bounds access in hns3, from Yunsheng Lin.

10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
    Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
    Neira Ayuso.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
  net: alx: make alx_drv_name static
  net: bpfilter: fix iptables failure if bpfilter_umh is disabled
  sock_diag: fix autoloading of the raw_diag module
  net: core: netpoll: Enable netconsole IPv6 link local address
  ipv6: properly check return value in inet6_dump_all()
  rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
  net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
  bonding/802.3ad: fix link_failure_count tracking
  net: phy: realtek: fix RTL8201F sysfs name
  sctp: define SCTP_SS_DEFAULT for Stream schedulers
  sctp: fix strchange_flags name for Stream Change Event
  mlxsw: spectrum: Fix IP2ME CPU policer configuration
  openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
  qed: fix link config error handling
  net: hns3: Fix for out-of-bounds access when setting pfc back pressure
  net/mlx4_en: use __netdev_tx_sent_queue()
  net: do not abort bulk send on BQL status
  net: bql: add __netdev_tx_sent_queue()
  s390/qeth: report 25Gbit link speed
  s390/qeth: sanitize ARP requests
  ...

Due to what appears to be a copy/paste error, the opening ENTRY()
of cpu_v7_hvc_switch_mm() lacks a matching ENDPROC(), and instead,
the one for cpu_v7_smc_switch_mm() is duplicated.

Given that it is ENDPROC() that emits the Thumb annotation, the
cpu_v7_hvc_switch_mm() routine will be called in ARM mode on a
Thumb2 kernel, resulting in the following splat:

  Internal error: Oops - undefined instruction: 0 [#1] SMP THUMB2
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc1-00030-g4d28ad89189d-dirty #488
  Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
  PC is at cpu_v7_hvc_switch_mm+0x12/0x18
  LR is at flush_old_exec+0x31b/0x570
  pc : [<c0316efe>]    lr : [<c04117c7>]    psr: 00000013
  sp : ee899e50  ip : 00000000  fp : 00000001
  r10: eda28f34  r9 : eda31800  r8 : c12470e0
  r7 : eda1fc00  r6 : eda53000  r5 : 00000000  r4 : ee88c000
  r3 : c0316eec  r2 : 00000001  r1 : eda53000  r0 : 6da6c000
  Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none

Note the 'ISA ARM' in the last line.

Fix this by using the correct name in ENDPROC().

Cc: <stable@vger.kernel.org>
Fixes: 10115105 ("ARM: spectre-v2: add firmware based hardening")
Reviewed-by: NDave Martin <Dave.Martin@arm.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains the first batch of Netfilter fixes for
your net tree:

1) Fix splat with IPv6 defragmenting locally generated fragments,
   from Florian Westphal.

2) Fix Incorrect check for missing attribute in nft_osf.

3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
   header, from Jiri Slaby.

4) Revert map lookup in nft_numgen, this is already possible with
   the existing infrastructure without this extension.

5) Fix wrong listing of set reference counter, make counter
   synchronous again, from Stefano Brivio.

6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.

7) Fix allocation failure with large set, use kvcalloc().
   From Andrey Ryabinin.

8) No need to disable BH when fetch ip set comment, patch from
   Jozsef Kadlecsik.

9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
   Taehee Yoo.

10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
    from Jozsef Kadlecsik.

11) Fix setting default timeout via nfnetlink_cttimeout, this
    comes with preparation patch to add nf_{tcp,udp,...}_pernet()
    helper.

12) Allow ebtables table nat to be of filter type via nft_compat.
    From Florian Westphal.

13) Incorrect calculation of next bucket in early_drop, do no bump
    hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.

test config:
   CONFIG_BPFILTER=y
   # CONFIG_BPFILTER_UMH is not set

test command:
   %iptables -L
   iptables: No chain/target/match by that name.

Fixes: d2ba09c1 ("net: add skeleton of bpfilter kernel module")
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.

Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Fixes: bf2ae2e4 ("sock_diag: request _diag module only when the family or proto has been registered")
Signed-off-by: NAndrei Vagin <avagin@gmail.com>
Reviewed-by: NCyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no reason to discard using source link local address when
remote netconsole IPv6 address is set to be link local one.

The patch allows administrators to use IPv6 netconsole without
explicitly configuring source address:

    netconsole=@/,@fe80::5054:ff:fe2f:6012/
Signed-off-by: NMatwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.

Fixes: 08e814c9 ("net/ipv6: Bail early if user only wants cloned entries")
Fixes: ae677bbb ("net: Don't return invalid table id error when dumping all families")
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.

Fix it by partially restoring the previous behavior before
commit c63586dc ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.

[1]:
unreferenced object 0xffff88001322a200 (size 96):
  comm "sshd", pid 1484, jiffies 4296032768 (age 1432.542s)
  hex dump (first 32 bytes):
    00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de  ................
    18 09 41 36 00 88 ff ff 18 09 41 36 00 88 ff ff  ..A6......A6....
  backtrace:
    [<0000000095846b39>] kmem_cache_alloc_trace+0x151/0x220
    [<000000007d12709f>] inet6_dump_fib+0x68d/0x940
    [<000000002775a316>] rtnl_dump_all+0x1d9/0x2d0
    [<00000000d7cd302b>] netlink_dump+0x945/0x11a0
    [<000000002f43485f>] __netlink_dump_start+0x55d/0x800
    [<00000000f76bbeec>] rtnetlink_rcv_msg+0x4fa/0xa00
    [<000000009b5761f3>] netlink_rcv_skb+0x29c/0x420
    [<0000000087a1dae1>] rtnetlink_rcv+0x15/0x20
    [<00000000691b703b>] netlink_unicast+0x4e3/0x6c0
    [<00000000b5be0204>] netlink_sendmsg+0x7f2/0xba0
    [<0000000096d2aa60>] sock_sendmsg+0xba/0xf0
    [<000000008c1b786f>] __sys_sendto+0x1e4/0x330
    [<0000000019587b3f>] __x64_sys_sendto+0xe1/0x1a0
    [<00000000071f4d56>] do_syscall_64+0x9f/0x300
    [<000000002737577f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<0000000057587684>] 0xffffffffffffffff

Fixes: c63586dc ("net: rtnl_dump_all needs to propagate error from dumpit function")
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.

Fixes: 2384d025 ("net/ipv6: Add anycast addresses to a global hashtable")
Signed-off-by: NJeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __no_sanitize_address_or_inline and __no_kasan_or_inline defines
are almost identical. The only difference is that __no_kasan_or_inline
does not have the 'notrace' attribute.

To be able to replace __no_sanitize_address_or_inline with the older
definition, add 'notrace' to __no_kasan_or_inline and change to two
users of __no_sanitize_address_or_inline in the s390 code.

The 'notrace' option is necessary for e.g. the __load_psw_mask function
in arch/s390/include/asm/processor.h. Without the option it is possible
to trace __load_psw_mask which leads to kernel stack overflow.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Pointed-out-by: NAndrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix strpbrk()'s argument order, it must pass acceptable string
in 2nd argument. Note that this can cause a kernel panic where
it recovers backup character to code->data.

Link: http://lkml.kernel.org/r/154108256792.2604.1816052586385217811.stgit@devbox

Fixes: a6682814 ("tracing/kprobes: Allow kprobe-events to record module symbol")
Signed-off-by: NMasami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>

Commit 4d2c0cda set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.

Fixes: 4d2c0cda ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: NHolger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.

SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: NJianwen Ji <jiji@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.

To keep the compatibility, fix it by adding two macros.

Fixes: b444153f ("sctp: add support for generating add stream change event notification")
Reported-by: NJianwen Ji <jiji@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-11-03

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
   to not use page start but actual start instead to work correctly with
   profiling e.g. finding hot instructions from stack traces. Also fix latter
   with regards to dumping address and jited len for !multi prog, from Song.

2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
   instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.

Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.

Fixes: 9148e7cf ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:

net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'

In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:

drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]

When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.

Fixes: c56a8be7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull scheduler fixes from Ingo Molnar:
 "A memory (under-)allocation fix and a comment fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/topology: Fix off by one bug
  sched/rt: Update comment in pick_next_task_rt()

Pull x86 fixes from Ingo Molnar:
 "A number of fixes and some late updates:

   - make in_compat_syscall() behavior on x86-32 similar to other
     platforms, this touches a number of generic files but is not
     intended to impact non-x86 platforms.

   - objtool fixes

   - PAT preemption fix

   - paravirt fixes/cleanups

   - cpufeatures updates for new instructions

   - earlyprintk quirk

   - make microcode version in sysfs world-readable (it is already
     world-readable in procfs)

   - minor cleanups and fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  compat: Cleanup in_compat_syscall() callers
  x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
  objtool: Support GCC 9 cold subfunction naming scheme
  x86/numa_emulation: Fix uniform-split numa emulation
  x86/paravirt: Remove unused _paravirt_ident_32
  x86/mm/pat: Disable preemption around __flush_tlb_all()
  x86/paravirt: Remove GPL from pv_ops export
  x86/traps: Use format string with panic() call
  x86: Clean up 'sizeof x' => 'sizeof(x)'
  x86/cpufeatures: Enumerate MOVDIR64B instruction
  x86/cpufeatures: Enumerate MOVDIRI instruction
  x86/earlyprintk: Add a force option for pciserial device
  objtool: Support per-function rodata sections
  x86/microcode: Make revision and processor flags world-readable

Pull perf updates and fixes from Ingo Molnar:
 "These are almost all tooling updates: 'perf top', 'perf trace' and
  'perf script' fixes and updates, an UAPI header sync with the merge
  window versions, license marker updates, much improved Sparc support
  from David Miller, and a number of fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
  perf intel-pt/bts: Calculate cpumode for synthesized samples
  perf intel-pt: Insert callchain context into synthesized callchains
  perf tools: Don't clone maps from parent when synthesizing forks
  perf top: Start display thread earlier
  tools headers uapi: Update linux/if_link.h header copy
  tools headers uapi: Update linux/netlink.h header copy
  tools headers: Sync the various kvm.h header copies
  tools include uapi: Update linux/mmap.h copy
  perf trace beauty: Use the mmap flags table generated from headers
  perf beauty: Wire up the mmap flags table generator to the Makefile
  perf beauty: Add a generator for MAP_ mmap's flag constants
  tools include uapi: Update asound.h copy
  tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
  tools include uapi: Update linux/fs.h copy
  perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
  perf cs-etm: Correct CPU mode for samples
  perf unwind: Take pgoff into account when reporting elf to libdwfl
  perf top: Do not use overwrite mode by default
  perf top: Allow disabling the overwrite mode
  perf trace: Beautify mount's first pathname arg
  ...

Pull irq fixes from Ingo Molnar:
 "An irqchip driver fix and a memory (over-)allocation fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
  irq/matrix: Fix memory overallocation

With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.

Fixed: 051f3ca0 ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Signed-off-by: NIngo Molnar <mingo@kernel.org>

The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.

[   35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14

[   35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[   35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[   35.254141] Workqueue: events work_for_cpu_fn
[   35.254144] Call trace:
[   35.254147]  dump_backtrace+0x0/0x2f0
[   35.254149]  show_stack+0x24/0x30
[   35.254154]  dump_stack+0x110/0x184
[   35.254157]  print_address_description+0x168/0x2b0
[   35.254160]  kasan_report+0x184/0x310
[   35.254162]  __asan_load2+0x7c/0xa0
[   35.254170]  hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254177]  hclge_tm_init_hw+0x794/0x9f0 [hclge]
[   35.254184]  hclge_tm_schd_init+0x48/0x58 [hclge]
[   35.254191]  hclge_init_ae_dev+0x778/0x1168 [hclge]
[   35.254196]  hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[   35.254206]  hns3_probe+0x88/0xa8 [hns3]
[   35.254210]  local_pci_probe+0x7c/0xf0
[   35.254212]  work_for_cpu_fn+0x34/0x50
[   35.254214]  process_one_work+0x4d4/0xa38
[   35.254216]  worker_thread+0x55c/0x8d8
[   35.254219]  kthread+0x1b0/0x1b8
[   35.254222]  ret_from_fork+0x10/0x1c

[   35.254224] The buggy address belongs to the page:
[   35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[   35.273835] flags: 0xfffff8000008000(head)
[   35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[   35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[   35.282012] page dumped because: kasan: bad access detected

[   35.282014] Memory state around the buggy address:
[   35.282017]  ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282019]  ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282022]                             ^
[   35.282024]  ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282026]  ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282028] ==================================================================
[   35.282029] Disabling lock debugging due to kernel taint
[   35.282747] hclge driver initialization finished.

Fixes: 67bf2541 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: bql: better deal with GSO

While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.

On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.

This patch series :

- Add __netdev_tx_sent_queue() so that drivers
  can implement efficient BQL and xmit_more support.

- Implement a work around in dev_hard_start_xmit()
  for drivers not using __netdev_tx_sent_queue()

- changes mlx4 to use __netdev_tx_sent_queue()

v2: Tariq and Willem feedback addressed.
    added __netdev_tx_sent_queue() (Willem suggestion)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

doorbell only depends on xmit_more and netif_tx_queue_stopped()

Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.

This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.

Problem is that GSO packets can end up comsuming more than
the BQL budget.

Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.

It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.

It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.

Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.

Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.

BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.

But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.

Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.

Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.

Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.

Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.

Code template in a driver might look like the following :

	send_doorbell = __netdev_tx_sent_queue(tx_queue, nr_bytes, skb->xmit_more);

Note that __netdev_tx_sent_queue() use is not mandatory,
since following patch will change dev_hard_start_xmit()
to not care about BQL status.

But it is highly recommended so that xmit_more full benefits
can be reached (less doorbells sent, and less atomic operations as well)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>