提交 73333626 编写于 作者: A Abhishek Shah 提交者: David S. Miller

net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay

This patch allows users to enable/disable internal TX and/or RX
clock delay for BCM5481x series PHYs so as to satisfy RGMII timing
specifications.

On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.
Signed-off-by: NAbhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 d8325650
......@@ -74,27 +74,40 @@ static int bcm54612e_config_init(struct phy_device *phydev)
return 0;
}
static int bcm54810_config(struct phy_device *phydev)
static int bcm5481x_config(struct phy_device *phydev)
{
int rc, val;
val = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
rc = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
val);
if (rc < 0)
return rc;
/* handling PHY's internal RX clock delay */
val = bcm54xx_auxctl_read(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
val |= MII_BCM54XX_AUXCTL_MISC_WREN;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
/* Disable RGMII RXC-RXD skew */
val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
}
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
/* Enable RGMII RXC-RXD skew */
val |= MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
}
rc = bcm54xx_auxctl_write(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC,
val);
if (rc < 0)
return rc;
/* handling PHY's internal TX clock delay */
val = bcm_phy_read_shadow(phydev, BCM54810_SHD_CLK_CTL);
val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
/* Disable internal TX clock delay */
val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
}
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
/* Enable internal TX clock delay */
val |= BCM54810_SHD_CLK_CTL_GTXCLK_EN;
}
rc = bcm_phy_write_shadow(phydev, BCM54810_SHD_CLK_CTL, val);
if (rc < 0)
return rc;
......@@ -244,7 +257,7 @@ static void bcm54xx_adjust_rxrefclk(struct phy_device *phydev)
static int bcm54xx_config_init(struct phy_device *phydev)
{
int reg, err;
int reg, err, val;
reg = phy_read(phydev, MII_BCM54XX_ECR);
if (reg < 0)
......@@ -283,8 +296,14 @@ static int bcm54xx_config_init(struct phy_device *phydev)
if (err)
return err;
} else if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54810) {
err = bcm54810_config(phydev);
if (err)
/* For BCM54810, we need to disable BroadR-Reach function */
val = bcm_phy_read_exp(phydev,
BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
err = bcm_phy_write_exp(phydev,
BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
val);
if (err < 0)
return err;
}
......@@ -392,29 +411,7 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
ret = genphy_config_aneg(phydev);
/* Then we can set up the delay. */
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
u16 reg;
/*
* There is no BCM5481 specification available, so down
* here is everything we know about "register 0x18". This
* at least helps BCM5481 to successfully receive packets
* on MPC8360E-RDK board. Peter Barada <peterb@logicpd.com>
* says: "This sets delay between the RXD and RXC signals
* instead of using trace lengths to achieve timing".
*/
/* Set RDX clk delay. */
reg = 0x7 | (0x7 << 12);
phy_write(phydev, 0x18, reg);
reg = phy_read(phydev, 0x18);
/* Set RDX-RXC skew. */
reg |= (1 << 8);
/* Write bits 14:0. */
reg |= (1 << 15);
phy_write(phydev, 0x18, reg);
}
bcm5481x_config(phydev);
if (of_property_read_bool(np, "enet-phy-lane-swap")) {
/* Lane Swap - Undocumented register...magic! */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册