The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.

But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).

Remove the not needed anymore dependency.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Following the removal of the "->policy" usage for PXA255 in patch
459fc208 (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.

It also cures the runtime warning that was printed each time the
frequency was changed.

Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.

Tested on an Arcom/Eurotech Viper.
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Acked-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

instead of holding them as static pointers.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This symbol is required by locomo backlight driver, exporting this
allows the driver to be built as a module.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NStefan Schmidt <stefan@datenfreihafen.org>

PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

for the reference of __REG() within <mach/hardware.h>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>

pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Original patch from Marek Vasut, the problems with PXA26x are:

1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
   inverted in GPDR2, as well as their alternate function bits being
   '1' for their GPIO functionality in GAFRx

2. there is no easy way to decide if the processor is a pxa26x or a
   pxa250/pxa255 at run-time, so the assumption here is the pxa26x
   will be treated as one of the pxa25x variants, and board code
   should have a better knowledge of the processor it is featured

Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.

Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.

__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This reverts commit da1a3dc0.

The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.

Also, fix the incorrect GPIO number passed in pxa27x_init_irq().

Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: NEric Miao <eric.miao@marvell.com>

PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Where 'pxa_dma_desc' and 'pxa_{request,free}_dma' are referenced.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
  [ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
  [ARM] pxa: fix I2C controller device being registered twice on Akita
  pxafb: only initialize the smart panel thread when dealing with a smartpanel
  pxafb: introduce LCD_TYPE_MASK and use it.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] xen: fix xen_get_eflags.
  [IA64] ia64/pv_ops/pv_cpu_ops: fix _IA64_REG_IP case.
  [IA64] remove duplicate include iommu.h
  [IA64] use mprintk instead of printk, in ia64_mca_modify_original_stack
  [IA64] Rationalize kernel mode alignment checking

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: ACE1001 patch for cp2101.c
  USB: usbmon: fix read(2)
  USB: gadget rndis: send notifications
  USB: gadget rndis: stop windows self-immolation
  USB: storage: update unusual_devs entries for Nokia 5300 and 5310
  USB: storage: updates unusual_devs entry for the Nokia 6300
  usb: musb: fix bug in musb_schedule
  USB: fix SB700 usb subsystem hang bug

fix xen_get_eflags. It doesn't take any argument.
Signed-off-by: NIsaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: NTony Luck <tony.luck@intel.com>

pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: NIsaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: NTony Luck <tony.luck@intel.com>

arch/ia64/kernel/pci-dma.c only needs to include iommu once.
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>