Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* ABRT_MASTER_DIS: Fix a typo.

* i2c_dw_handle_tx_abort: Return an appropriate error number
  depending on abort_source.

* i2c_dw_xfer: Add a missing abort_source initialization.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Suppose TX_ABRT occurs in the middle of processing i2c_msg msgs[], and
a STOP condition has already been generated on the bus.  In this case,
subsequent i2c_dw_xfer_msg() might initiate a new and unnecessary I2C
transaction, which we'd have to avoid.

Furthermore, anytime TX_ABRT is set, the contents of tx/rx buffers are
flushed, so we don't have to process RX_FULL and TX_EMPTY.

Disable interrupts, and skip them.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Current error handling procedures are not good in two respects:

* Forgot to mark dev->cmd_complete as "completed" on errors

  Once an I2C transaction is initiated, wait_for_completion_
  interruptible_timeout() waits for dev->cmd_complete to be completed.
  We have to take care of it whenever an error is detected, otherwise
  we will have a needless HZ timeout.

* Forgot to disable interrupts

  In the previous patch, interrupt mask operations have been changed.
  We don't disable interrupts at the end of the interrupt handler any
  more, and try to keep RX_FULL (and TX_EMPTY if required) enabled
  during the transaction so that we can send longer data than the size
  of Tx/Rx FIFO.

  If an error is detected, we need to disable interrupts before
  quitting current transaction.

We can work around above points using dev->msg_err effectively.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Currently we disable TX_EMPTY interrupt when buf_len is zero, but this
is wrong.  (buf_len == 0) means that all transmit data in the current
i2c_msg message has been sent out, but that doesn't necessarily mean
all i2c_msg messages have been processed.

TX_EMPTY interrupt is used as the driving force of DW I2C transactions,
so we need to keep it enabled as long as i2c_msg messages are available.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Currently we process the first i2c_dw_xfer_msg() in i2c_dw_xfer(),
but in this case there is a possibility to be interrupted by certain
interrupts.  As described before in this patchset, we need to keep
providing new transmit data within a given time period, otherwise Tx
FIFO underrun takes place and STOP condition will be generated on the
bus, even if we have more bytes to be written.

In order to exclude all such possibilities, change TX_EMPTY interrupt
usage as below:

* DW_IC_INTR_DEFAULT_MASK: Define a default interrupt mask set, and
  put TX_EMPTY there.

* i2c_dw_xfer_init: Enable DW_IC_INTR_DEFAULT_MASK prior to initiating
  a new I2C transaction.  The first TX_EMPTY will be triggered shortly.
  With the help of it, we can make the first call to i2c_dw_xfer_msg()
  in the interrupt handler.

* i2c_dw_xfer_msg: Fixup intr_mask operation accordingly.  Make sure
  that TX_EMPTY operations need to be reversed.

* request_irq: Set IRQF_DISABLED so that we could load transmit data
  into Tx FIFO without being distracted by other interrupts.

* Remove i2c_dw_xfer_msg() in i2c_dw_xfer().
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

I2c_dw_xfer_msg() also has the same target address inconsistency check,
and furthermore it checks across all i2c_msg messages, while
i2c_dw_read() walks through i2c_msg messages only with_ I2C_M_RD flag.
That is, target address check in i2c_dw_read() is redundant and useless.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Set proper I2C_FUNC_SMBUS_* bits so that the driver could be used with
some utilities requiring SMBus functionalities, such as i2c-tools.

Note that DW I2C core doesn't support I2C_FUNC_SMBUS_QUICK, as it's not
capable of zero-length data transactions.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

As the driver and hardware always process the given data in parallel,
then it would be better to initialize tx_limit, rx_limit and rx_valid
variables just prior to being used.

This will help us to send / receive as much data as possible.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

While we have a local variable "buf_len" for dev->tx_buf_len, we don't
have such local variable for dev->tx_buf pointer.  While "buf_len" is
restored at first then updated when we start processing a new i2c_msg
(determined by STATUS_WRITE_IN_PROGRESS flag), ->tx_buf is different.

Such inconsistency makes the code slightly hard to follow.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We have some steps at the top of i2c_dw_xfer_msg() to set up a slave
address and enable DW I2C core.  And it's executed only when we don't
have STATUS_WRITE_IN_PROGRESS.

But we need to make sure that STATUS_WRITE_IN_PROGRESS only indicates
that we have a pending i2c_msg to process.  In other words, even if
STATUS_WRITE_IN_PROGRESS is not set, that doesn't mean we're at initial
state in the I2C transaction.

Since i2c_dw_xfer_msg() will be invoked again and again during a
transaction, those init steps have a possibility to be re-processed
needlessly.  For example, this issue easily takes place when processing
a combined transaction with a certain condition (the number of tx bytes
in the first i2c_msg, equals to the Tx FIFO depth).

Consequently we should not use STATUS_WRITE_IN_PROGRESS to determine
where we're at in an I2C transaction.  It would be better to separate
those initialization steps from i2c_dw_xfer_msg().
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Enable RX_FULL interrupt mask by default, and hook it in the interrupt
handler.  If requested amount of rx data (defined by IC_RX_TL) is not
available, we don't have to process i2c_dw_read().
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

As a hardware feature, DW I2C core generates a STOP condition whenever
the Tx FIFO becomes empty (strictly speaking, whenever the last byte in
the Tx FIFO is sent out), even if we have more bytes to be written.

In other words, we must never make "Tx FIFO underrun" happen during
a transaction, except for the last byte.  For the safety's sake, we'd
make TX_EMPTY interrupt get triggered every time one byte is processed.

The Rx FIFO threshold needs to be set as well.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Symptom:
--------
When we're going to send/receive the longer size of data than the Tx
FIFO length, the I2C transaction will be divided into several separated
transactions, limited by the Tx FIFO length.

Details:
--------
As a hardware feature, DW I2C core generates a STOP condition whenever
the Tx FIFO becomes empty (strictly speaking, whenever the last byte in
the Tx FIFO is sent out), even if we have more bytes to be written.
Then, once a new transmit data is written to the Tx FIFO, DW I2C core
will initiate a new transaction, which leads to another START condition.

This explains how the transaction in question goes, and implies that
current tasklet-based dw_i2c_pump_msg() strategy couldn't meet the
timing constraint required for avoiding Tx FIFO underrun.

To avoid this scenario, we must keep providing new transmit data within
a given time period.  In case of Fast-mode + 32-byte Tx FIFO, for
instance, it takes about 22.5[us] to process single byte, and 720[us] in
total.

This patch removes the existing tasklet-based "pump" system, and move
its jobs into the interrupt handler.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

In case a work-in-progress i2c_msg has more bytes to be written, we
need to set STATUS_WRITE_IN_PROGRESS and exit from the msg_write_idx-
searching loop.  Otherwise, we will overtake the current msg_write_idx
without waiting for its transmission to be processed.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* Calculate with accurate conditional expressions from DW manuals.
* Round ic_clk by adding 0.5 as it's important at high ic_clk rate.
* Take into account "tHD;STA" issue for _HCNT calculation.
* Take into account "tf" for _LCNT calculation.
* Add "cond" and "offset" fot further correction requirements.

For _HCNT calculation, there's one issue needs to be carefully
considered; DesignWare I2C core doesn't seem to have solid strategy
to meet the tHD;STA timing spec.  If you configure _HCNT based on the
tHIGH timing spec, it easily results in violation of the tHD;STA spec.

After many trials, we came to the conclusion that the tHD;STA period
is proportional to (_HCNT + 3).  For the safety's sake, this should be
selected by default.

As for _LCNT calculation, DW I2C core has one characteristic behavior;
he starts counting the SCL CNTs for the LOW period of the SCL clock
(tLOW) as soon as it pulls the SCL line.  At that time, he doesn't take
into account the fall time of SCL signal (tf), IOW, he starts counting
CNTs without confirming the SCL input voltage has dropped to below VIL.

This characteristics becomes a problem on some platforms where tf is
considerably long, and results in violation of the tLOW timing spec.

To make the driver configurable as much as possible for various cases,
we'd have separated arguments "tf" and "offset", and for safety default
values should be 0.3 us and 0, respectively.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We couldn't know the original intent for this variable, but at this
point it's useless.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We don't have to use "struct i2c_adapter" pointer here.
Let's use a local "struct dw_i2c_dev" pointer, instead.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We don't have to use "struct i2c_adapter" pointer here.
Let's use a local "struct dw_i2c_dev" pointer, instead.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We're strongly discouraged from using the IC_CLR_INTR register because
it clears all software-clearable interrupts asserted at the moment.

  stat = readl(IC_INTR_STAT);
    :
    :  <=== Interrupts asserted during this period will be lost
    :
  readl(IC_CLR_INTR);

Instead, use the separately-prepared IC_CLR_* registers.

At the same time, this patch adds all remaining interrupt definitions
available in the DesignWare I2C hardware.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This driver looks originally meant for armel machines where readw()/
writew() works perfectly fine with this hardware.  But that doens't
work for big-endian systems.

This patch converts all 8/16-bit-aware usages to 32-bit variants.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
  cfq-iosched: Do not access cfqq after freeing it
  block: include linux/err.h to use ERR_PTR
  cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
  blkio: Allow CFQ group IO scheduling even when CFQ is a module
  blkio: Implement dynamic io controlling policy registration
  blkio: Export some symbols from blkio as its user CFQ can be a module
  block: Fix io_context leak after failure of clone with CLONE_IO
  block: Fix io_context leak after clone with CLONE_IO
  cfq-iosched: make nonrot check logic consistent
  io controller: quick fix for blk-cgroup and modular CFQ
  cfq-iosched: move IO controller declerations to a header file
  cfq-iosched: fix compile problem with !CONFIG_CGROUP
  blkio: Documentation
  blkio: Wait on sync-noidle queue even if rq_noidle = 1
  blkio: Implement group_isolation tunable
  blkio: Determine async workload length based on total number of queues
  blkio: Wait for cfq queue to get backlogged if group is empty
  blkio: Propagate cgroup weight updation to cfq groups
  blkio: Drop the reference to queue once the task changes cgroup
  blkio: Provide some isolation between groups
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
  Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
  libata: Clarify ata_set_lba_range_entries function
  libata: Report zeroed read after TRIM and max discard size
  pata_hpt3x2n: fix overclocked MWDMA0 timing
  pata_it8213: MWDMA0 is unsupported
  [libata] MWDMA0 is unsupported on PIIX-like PATA controllers
  pata_via: clear UDMA transfer mode bit for PIO and MWDMA
  pata_sis: Power Management fix
  pata_rz1000: Power Management fix
  pata_radisys: fix UDMA handling
  pata_ns87415: Power Management fix
  pata_marvell: fix marvell_pre_reset() documentation
  pata_legacy: add pointers to QDI65x0 documentation
  pata_legacy: fix access to control register for QDI6580
  pata_legacy: fix QDI6580DP support
  pata_it8213: fix it8213_pre_reset() documentation
  pata_it8213: fix wrong MWDMA timings being programmed
  pata_it8213: fix PIO2 underclocking
  pata_it8213: fix wrong PIO timings being programmed
  pata_it8213: fix UDMA handling
  ...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (149 commits)
  arm: omap: Add omap3_defconfig
  AM35xx: Defconfig for AM3517 EVM board
  AM35xx: Add support for AM3517 EVM board
  omap: 3630sdp: defconfig creation
  omap: 3630sdp: introduce 3630 sdp board support
  omap3: Add defconfig for IGEP v2 board
  omap3: Add minimal IGEP v2 support
  omap3: Add CompuLab CM-T35 defconfig
  omap3: Add CompuLab CM-T35 board support
  omap3: rx51: Add wl1251 wlan driver support
  omap3: rx51: Add SDRAM init
  omap1: Add default kernel configuration for Herald
  omap1: Add board support and LCD for HTC Herald
  omap: zoom2: update defconfig for LL_DEBUG_NONE
  omap: zoom3: defconfig creation
  omap3: zoom: Introduce zoom3 board support
  omap3: zoom: Drop i2c-1 speed to 2400
  omap3: zoom: rename zoom2 name to generic zoom
  omap3: zoom: split board file for software reuse
  omap3evm: MIgrate to smsc911x ethernet driver
  ...

Fix trivial conflict (two unrelated config options added next to each
other) in arch/arm/mach-omap2/Makefile

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: parport_mfc3 - Not makes it a bool before the comparison.
  m68k: don't export static inline functions
  fbdev: atafb - add palette register check
  m68k: Remove the BKL from sys_execve
  m68k: Cleanup linker scripts using new linker script macros.
  m68k: Make thread_info.h usable from assembly.
  m68knommu: define arch_has_single_step() and friends
  m68k: ptrace fixes
  m68k: use generic code for ptrace requests
  rtc: Add an RTC driver for the Ricoh RP5C01
  rtc: Add an RTC driver for the Oki MSM6242

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  ieee1394: Use hweight32
  firewire: cdev: reduce stack usage by ioctl_dispatch
  firewire: ohci: 0 may be a valid DMA address
  firewire: core: WARN on wrong usage of core transaction functions
  firewire: core: optimize Topology Map creation
  firewire: core: clarify generate_config_rom usage
  firewire: optimize config ROM creation
  firewire: cdev: normalize variable names
  firewire: normalize style of queue_work wrappers
  firewire: cdev: fix memory leak in an error path

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (272 commits)
  Fix soc_common PCMCIA configuration
  ARM: 5827/1: SA1100: h3100/h3600: emit messages on failed gpio_request
  ARM: 5826/1: SA1100: h3100/h3600: always build htc-egpio driver
  ARM: 5825/1: SA1100: h3600: update defconfig
  ARM: 5824/1: SA1100: reuse h3600 PCMCIA driver on h3100
  ARM: 5823/1: SA1100: h3100/h3600: add support for gpio-keys
  ARM: 5822/1: SA1100: h3100/h3600: clean up #includes
  ARM: 5821/1: SA1100: h3100/h3600: revise copyright boilerplates
  ARM: 5820/1: SA1100: h3100/h3600: split h3600.c
  ARM: 5819/1: SA1100: h3100/h3600: merge h3600.h and h3600_gpio.h into h3xxx.h
  ARM: 5818/1: SA1100: h3100/h3600: drop old GPIO definitions
  ARM: 5817/1: SA1100: h3100/h3600: configure all unused gpios as inputs
  ARM: 5816/1: SA1100: h3600: remove IRQ_GPIO_* definitions
  ARM: 5815/1: SA1100: h3100/h3600: remove now unused assign_h3600_egpio handlers
  ARM: 5814/1: SA1100: h3100/h3600: convert all users of assign_h3600_egpio to gpiolib
  ARM: 5813/1: SA1100: h3100/h3600: add htc-egpio driver
  ARM: 5812/1: SA1100: h3100/h3600: separate machine-specific LCD helpers
  ARM: 5811/2: pcmcia: convert sa1100_h3600 driver to gpiolib
  ARM: 5799/1: SA1100: h3600: stop setting direction for LCD pins
  ARM: 5798/1: SA1100: h3600: remove unused cruft from h3600.h
  ...

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-stub: Documentation update
  i2c-stub: Allow user to disable some commands
  i2c-stub: Implement I2C block support
  i2c: Refactor for_each callbacks
  i2c-i801: Retry on lost arbitration
  i2c: Remove big kernel lock from i2cdev_open
  ics932s401: Clean up detect function
  i2c: Simplify i2c_detect_address
  i2c: Drop probe, ignore and force module parameters
  i2c: Add missing __devinit markers to old i2c adapter drivers
  i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
  i2c: Prevent priority inversion on top of bus lock
  i2c-voodoo3: Delete
  i2c-powermac: Drop temporary name buffer
  i2c-powermac: Include the i2c_adapter in struct pmac_i2c_bus
  i2c-powermac: Log errors
  i2c-powermac: Refactor i2c_powermac_smbus_xfer
  i2c-powermac: Reject unsupported I2C transactions
  i2c/chips: Move ds1682 to drivers/misc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Add flag for devices capable of generating run-time wake-up events
  PM / Runtime: Remove unnecessary braces in __pm_runtime_set_status()
  PM / Runtime: Make documentation of runtime_idle() agree with the code
  PM / Runtime: Ensure timer_expires is nonzero in pm_schedule_suspend()
  PM / Runtime: Use deferred_resume flag in pm_request_resume
  PM / Runtime: Export the PM runtime workqueue
  PM / Runtime: Fix lockdep warning in __pm_runtime_set_status()
  PM / Hibernate: Swap, use KERN_CONT
  PM / Hibernate: Shift remaining code from swsusp.c to hibernate.c
  PM / Hibernate: Move swap functions to kernel/power/swap.c.
  PM / freezer: Don't get over-anxious while waiting

* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
  KVM: VMX: Fix comparison of guest efer with stale host value
  KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
  KVM: Drop user return notifier when disabling virtualization on a cpu
  KVM: VMX: Disable unrestricted guest when EPT disabled
  KVM: x86 emulator: limit instructions to 15 bytes
  KVM: s390: Make psw available on all exits, not just a subset
  KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
  KVM: VMX: Report unexpected simultaneous exceptions as internal errors
  KVM: Allow internal errors reported to userspace to carry extra data
  KVM: Reorder IOCTLs in main kvm.h
  KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
  KVM: only clear irq_source_id if irqchip is present
  KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
  KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
  KVM: VMX: Remove vmx->msr_offset_efer
  KVM: MMU: update invlpg handler comment
  KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
  KVM: remove duplicated task_switch check
  KVM: powerpc: Fix BUILD_BUG_ON condition
  KVM: VMX: Use shared msr infrastructure
  ...

Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
  mac80211: fix reorder buffer release
  iwmc3200wifi: Enable wimax core through module parameter
  iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
  iwmc3200wifi: Coex table command does not expect a response
  iwmc3200wifi: Update wiwi priority table
  iwlwifi: driver version track kernel version
  iwlwifi: indicate uCode type when fail dump error/event log
  iwl3945: remove duplicated event logging code
  b43: fix two warnings
  ipw2100: fix rebooting hang with driver loaded
  cfg80211: indent regulatory messages with spaces
  iwmc3200wifi: fix NULL pointer dereference in pmkid update
  mac80211: Fix TX status reporting for injected data frames
  ath9k: enable 2GHz band only if the device supports it
  airo: Fix integer overflow warning
  rt2x00: Fix padding bug on L2PAD devices.
  WE: Fix set events not propagated
  b43legacy: avoid PPC fault during resume
  b43: avoid PPC fault during resume
  tcp: fix a timewait refcnt race
  ...

Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
	kernel/sysctl_check.c
	net/ipv4/sysctl_net_ipv4.c
	net/ipv6/addrconf.c
	net/sctp/sysctl.c

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
  sparc: Set UTS_MACHINE correctly.
  sparc,leon: init_leon srmmu cleanup
  sparc32: Remove early interrupt enable.
  sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
  sparc64: Faster early-boot framebuffer console.
  Revert "sparc: Make atomic locks raw"
  sparc: remove unused nfsd #includes
  sparc: Fixup last users of irq_chip->typename
  Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
  No auxio on LEON
  apbuart: Use of_find_node_by_path to find root node.
  sparc: Replace old style lock initializer
  sparc: Make atomic locks raw
  apbuart: Fix build and missing driver unregister.
  apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
  apbuart: Fix build warning.
  sparc: Support for GRLIB APBUART serial port
  watchdog: Remove BKL from rio watchdog driver
  sparc: Remove BKL from apc
  sparc,leon: Sparc-Leon SMP support

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (294 commits)
  S3C64XX: Staticise platform data for PCM devices
  ASoC: Rename controls with a / in wm_hubs
  snd-fm801: autodetect SF64-PCR (tuner-only) card
  ALSA: tea575x-tuner: fix mute
  ASoC: au1x: dbdma2: plug memleak in pcm device creation error path
  ASoC: au1x: dbdma2: fix oops on soc device removal.
  ALSA: hda - Fix memory leaks in the previous patch
  ALSA: hda - Add ALC661/259, ALC892/888VD support
  ALSA: opti9xx: remove snd_opti9xx fields
  ALSA: aaci - Clean up duplicate code
  ALSA: usb - Fix mixer map for Hercules Gamesurround Muse Pocket LT
  ALSA: hda - Add position_fix quirk for HP dv3
  ALSA: hda - Add a pin-fix for FSC Amilo Pi1505
  ALSA: hda - Fix Cxt5047 test mode
  ASoC: pxa/raumfeld: adopt new snd_soc_dai_set_pll() API
  ASoC: sh: fsi: Add runtime PM support
  sh: ms7724se: Add runtime PM support for FSI
  ALSA: hda - Add a position_fix quirk for MSI Wind U115
  ALSA: opti-miro: add PnP detection
  ALSA: opti-miro: separate comon probing code
  ...

* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
  of: merge of_find_all_nodes() implementations
  of: merge other miscellaneous prototypes
  of: merge of_*_flat_dt*() functions
  of: merge of_node_get(), of_node_put() and of_find_all_nodes()
  of: merge of_read_number() an of_read_ulong()
  of: merge of_node_*_flag() and set_node_proc_entry()
  of: merge struct boot_param_header from Microblaze and PowerPC
  of: add common header for flattened device tree representation
  of: Move OF_IS_DYNAMIC and OF_MARK_DYNAMIC macros to of.h
  of: merge struct device_node
  of: merge phandle, ihandle and struct property
  of: Rework linux/of.h and asm/prom.h include ordering

* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
  security/tomoyo: Remove now unnecessary handling of security_sysctl.
  security/tomoyo: Add a special case to handle accesses through the internal proc mount.
  sysctl: Drop & in front of every proc_handler.
  sysctl: Remove CTL_NONE and CTL_UNNUMBERED
  sysctl: kill dead ctl_handler definitions.
  sysctl: Remove the last of the generic binary sysctl support
  sysctl net: Remove unused binary sysctl code
  sysctl security/tomoyo: Don't look at ctl_name
  sysctl arm: Remove binary sysctl support
  sysctl x86: Remove dead binary sysctl support
  sysctl sh: Remove dead binary sysctl support
  sysctl powerpc: Remove dead binary sysctl support
  sysctl ia64: Remove dead binary sysctl support
  sysctl s390: Remove dead sysctl binary support
  sysctl frv: Remove dead binary sysctl support
  sysctl mips/lasat: Remove dead binary sysctl support
  sysctl drivers: Remove dead binary sysctl support
  sysctl crypto: Remove dead binary sysctl support
  sysctl security/keys: Remove dead binary sysctl support
  sysctl kernel: Remove binary sysctl logic
  ...

Fix a crash during boot reported by Jeff Moyer. Fix the issue of accessing
cfqq after freeing it.
Reported-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Reviewed-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NJens Axboe <axboe@carl.(none)>

This reverts commit f20941f3.

Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number.  Thus the second
argument will always "win" as a minimal one"

Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio().  The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."

Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>