提交 f20941f3 编写于 作者: A Alan Cox 提交者: Jeff Garzik

pata_sis: Implement MWDMA for the UDMA 133 capable chips

Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
上级 10734fc8
......@@ -252,24 +252,25 @@ static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
}
/**
* sis_133_set_piomode - Initialize host controller PATA PIO timings
* sis_133_do_piomode - Initialize host controller PATA PIO/DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
* Set PIO mode for device, in host controller PCI config space. This
* function handles PIO set up for the later ATA133 devices.
* function handles PIO set up for the later ATA133 devices. The same
* timings are used for MWDMA.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
static void sis_133_do_piomode(struct ata_port *ap, struct ata_device *adev,
int speed)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = 0x40;
u32 t1;
u32 reg54;
int speed = adev->pio_mode - XFER_PIO_0;
const u32 timing133[] = {
0x28269000, /* Recovery << 24 | Act << 16 | Ini << 12 */
......@@ -304,6 +305,42 @@ static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
pci_write_config_byte(pdev, port, t1);
}
/**
* sis_133_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
* Set PIO mode for device, in host controller PCI config space. This
* function handles PIO set up for the later ATA133 devices.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
sis_133_do_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
}
/**
* mwdma_clip_to_pio - clip MWDMA mode
* @adev: device
*
* As the SiS shared MWDMA and PIO timings we must program the equivalent
* PIO timing for the MWDMA mode but we must not program one higher than
* the permitted PIO timing of the device.
*/
static int mwdma_clip_to_pio(struct ata_device *adev)
{
const int mwdma_to_pio[3] = {
XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
};
return min(mwdma_to_pio[adev->dma_mode - XFER_MW_DMA_0],
adev->pio_mode - XFER_PIO_0);
}
/**
* sis_old_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
......@@ -332,6 +369,7 @@ static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higher bits are dependant on the device */
speed = mwdma_clip_to_pio(adev);
timing &= ~0x870F;
timing |= mwdma_bits[speed];
} else {
......@@ -372,6 +410,7 @@ static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higher bits are dependant on the device, bit 15 udma */
speed = mwdma_clip_to_pio(adev);
timing &= ~0x870F;
timing |= mwdma_bits[speed];
} else {
......@@ -389,7 +428,7 @@ static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
* Handles UDMA66 and early UDMA100 devices.
* Handles later UDMA100 devices.
*
* LOCKING:
* None (inherited from caller).
......@@ -400,21 +439,25 @@ static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_old_port_base(adev);
u8 timing;
u16 timing;
const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
const u16 udma_bits[] = {
0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
const u8 mwdma_bits[] = { 0x08, 0x32, 0x31 };
pci_read_config_byte(pdev, drive_pci + 1, &timing);
pci_read_config_word(pdev, drive_pci, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
speed = mwdma_clip_to_pio(adev);
timing &= ~0x80FF;
timing |= mwdma_bits[speed];
} else {
/* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x8F;
timing &= ~0x8F00;
timing |= udma_bits[speed];
}
pci_write_config_byte(pdev, drive_pci + 1, timing);
pci_write_config_word(pdev, drive_pci, timing);
}
/**
......@@ -434,21 +477,26 @@ static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *a
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_old_port_base(adev);
u8 timing;
/* Low 4 bits are timing */
static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82, 0x81};
u16 timing;
/* Bits 15-12 are timing */
static const u16 udma_bits[] = {
0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100
};
static const u8 mwdma_bits[] = { 0x08, 0x32, 0x31 };
pci_read_config_byte(pdev, drive_pci + 1, &timing);
pci_read_config_word(pdev, drive_pci, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
speed = mwdma_clip_to_pio(adev);
timing &= ~0x80FF;
timing = mwdma_bits[speed];
} else {
/* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x8F;
timing &= ~0x8F00;
timing |= udma_bits[speed];
}
pci_write_config_byte(pdev, drive_pci + 1, timing);
pci_write_config_word(pdev, drive_pci, timing);
}
/**
......@@ -479,13 +527,12 @@ static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
if (reg54 & 0x40000000)
port = 0x70;
port += (8 * ap->port_no) + (4 * adev->devno);
pci_read_config_dword(pdev, port, &t1);
if (adev->dma_mode < XFER_UDMA_0) {
t1 &= ~0x00000004;
/* FIXME: need data sheet to add MWDMA here. Also lacking on
ide/pci driver */
speed = mwdma_clip_to_pio(adev);
sis_133_do_piomode(ap, adev, speed);
t1 &= ~4; /* UDMA off */
} else {
speed = adev->dma_mode - XFER_UDMA_0;
/* if & 8 no UDMA133 - need info for ... */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册