This isn't supported when we emulate eswitch vlan push action which
is the current state of things.

Fixes: 8b32580d ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Address these sparse warnings on drivers/net/ethernet/mellanox/mlx5

[..]/core/diag/fs_tracepoint.c:99:53: warning: non-constant initializer for static object
[..]/core/diag/fs_tracepoint.c:102:53: warning: non-constant initializer for static object

etc
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix these gcc warnings on drivers/net/ethernet/mellanox/mlx5:

[..]/core/lib/clock.c:454:6: warning: no previous prototype for 'mlx5_init_clock' [-Wmissing-prototypes]
[..]/core/lib/clock.c:510:6: warning: no previous prototype for 'mlx5_cleanup_clock' [-Wmissing-prototypes]
[..]/core/en_main.c:3141:5: warning: no previous prototype for 'mlx5e_setup_tc' [-Wmissing-prototypes]
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Driver tries to copy at least MLX5E_MIN_INLINE bytes into the control
segment of the WQE. It assumes that the linear part contains at least
MLX5E_MIN_INLINE bytes, which can be wrong.

Cited commit verified that driver will not copy more bytes into the
inline header part that the actual size of the packet. Re-factor this
check to make sure we do not exceed the linear part as well.

This fix is aligned with the current driver's assumption that the entire
L2 will be present in the linear part of the SKB.

Fixes: 6aace17e ("net/mlx5e: Fix inline header size for small packets")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When GRO is off, the transport header pointer in sk_buff is
initialized to network's header.

To find the udp header, instead of using udp_hdr() which assumes
skb_network_header was set, manually calculate the udp header offset.

Fixes: 0952da79 ("net/mlx5e: Add support for loopback selftest")
Signed-off-by: NInbar Karmy <inbark@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When receiving an LRO packet, the checksum field is set by the hardware
to the checksum of the first coalesced packet. Obviously, this checksum
is not valid for the merged LRO packet and should be fixed.  We can use
the CQE checksum which covers the checksum of the entire merged packet
TCP payload to help us calculate the checksum incrementally.

Tested by sending IPv4/6 traffic with LRO enabled, RX checksum disabled
and watching nstat checksum error counters (in addition to the obvious
bandwidth drop caused by checksum errors).

This bug is usually "hidden" since LRO packets would go through the
CHECKSUM_UNNECESSARY flow which does not validate the packet checksum.

It's important to note that previous to this patch, LRO packets provided
with CHECKSUM_UNNECESSARY are indeed packets with a correct validated
checksum (even though the checksum inside the TCP header is incorrect),
since the hardware LRO aggregation is terminated upon receiving a packet
with bad checksum.

Fixes: e586b3b0 ("net/mlx5: Ethernet Datapath files")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.

For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.

Improve code readability by removing this redundant code.
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.

Commit 0a764db1 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.

Just like commit 0a764db1 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating RX or TX buffer pools, the driver needs to provide a
unique mapping ID to firmware for each pool. This value is assigned
using a counter which is incremented after a new pool is created. The
ID can be an integer ranging from 1-255. When migrating to a device
that requests a different number of queues, this value was not being
reset properly. As a result, after enough migrations, the counter
exceeded the upper bound and pool creation failed. This is fixed by
resetting the counter to one in this case.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This condition wasn't adjusted when PHY_IGNORE_INTERRUPT (-2) was added
long ago. In case of PHY_IGNORE_INTERRUPT the MAC interrupt indicates
also PHY state changes and we should do what the symbol says.

Fixes: 84a527a4 ("net: phylib: fix interrupts re-enablement in phy_start")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Cavium thunder nicvf driver supports rx/tx rings of up to 65536 entries per.
The number of entires are stored in the q_len member of struct q_desc_mem. The
problem is that q_len being a u16, results in 65536 becoming 0.

In getting pointers to descriptors in the rings, the driver uses q_len minus 1
as a mask after incrementing the pointer, in order to go back to the beginning
and not go past the end of the ring.

With the q_len set to 0 the mask is no longer correct and the driver does go
beyond the end of the ring, causing various ills. Usually the first thing that
shows up is a "NETDEV WATCHDOG: enP2p1s0f1 (nicvf): transmit queue 7 timed out"
warning.

This patch remedies the problem by changing q_len to a u32.
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While handling a driver reset we get a H_CLOSED return trying
to send a CRQ event. When this occurs we need to queue up another
reset attempt. Without doing this we see instances where the driver
is left in a closed state because the reset failed and there is no
further attempts to reset the driver.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using devmap to redirect packets between interfaces,
xdp_do_flush() is usually a must to flush any batched
packets. Unfortunately this is missed in current tuntap
implementation.

Unlike most hardware driver which did XDP inside NAPI loop and call
xdp_do_flush() at then end of each round of poll. TAP did it in the
context of process e.g tun_get_user(). So fix this by count the
pending redirected packets and flush when it exceeds NAPI_POLL_WEIGHT
or MSG_MORE was cleared by sendmsg() caller.

With this fix, xdp_redirect_map works again between two TAPs.

Fixes: 761876c8 ("tap: XDP support")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DKMS and similar out-of-tree module replacement services use
module version to make sure the out-of-tree software is not
older than the module shipped with the kernel.  We use the
kernel version in ethtool -i output, put it into MODULE_VERSION
as well.
Reported-by: NJan Gutter <jan.gutter@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most FWs limit the number of TSO segments a frame can produce
to 64.  This is for fairness and efficiency (of FW datapath)
reasons.  If a frame with larger number of segments is submitted
the FW will drop it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All netdevs which can accept TC offloads must implement
.ndo_set_features().  nfp_reprs currently do not do that, which
means hw-tc-offload can be turned on and off even when offloads
are active.

Whether the offloads are active is really a question to nfp_ports,
so remove the per-app tc_busy callback indirection thing, and
simply count the number of offloaded items in nfp_port structure.

Fixes: 8a276873 ("nfp: provide infrastructure for offloading flower based TC filters")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Tested-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_port is a structure which represents an ASIC port, both
PCIe vNIC (on a PF or a VF) or the external MAC port.  vNIC
netdev (struct nfp_net) and pure representor netdev (struct
nfp_repr) both have a pointer to this structure.  nfp_reprs
always have a port associated.  nfp_nets, however, only represent
a device port in legacy mode, where they are considered the
MAC port. In switchdev mode they are just the CPU's side of
the PCIe link.

By definition TC offloads only apply to device ports.  Don't
set the flag on vNICs without a port (i.e. in switchdev mode).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Tested-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upcoming changes will require all netdevs supporting TC offloads
to have a full struct nfp_port.  Require those for BPF offload.
The operation without management FW reporting information about
Ethernet ports is something we only support for very old and very
basic NIC firmwares anyway.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Tested-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 9ed4f916.

The commit introduced a regression that over read the ie with
the padding.

- the expected IE information

ath10k_pci 0000:03:00.0: found firmware features ie (1 B)
ath10k_pci 0000:03:00.0: Enabling feature bit: 6
ath10k_pci 0000:03:00.0: Enabling feature bit: 7
ath10k_pci 0000:03:00.0: features
ath10k_pci 0000:03:00.0: 00000000: c0 00 00 00 00 00 00 00

- the wrong IE with padding is read (0x77)

ath10k_pci 0000:03:00.0: found firmware features ie (4 B)
ath10k_pci 0000:03:00.0: Enabling feature bit: 6
ath10k_pci 0000:03:00.0: Enabling feature bit: 7
ath10k_pci 0000:03:00.0: Enabling feature bit: 8
ath10k_pci 0000:03:00.0: Enabling feature bit: 9
ath10k_pci 0000:03:00.0: Enabling feature bit: 10
ath10k_pci 0000:03:00.0: Enabling feature bit: 12
ath10k_pci 0000:03:00.0: Enabling feature bit: 13
ath10k_pci 0000:03:00.0: Enabling feature bit: 14
ath10k_pci 0000:03:00.0: Enabling feature bit: 16
ath10k_pci 0000:03:00.0: Enabling feature bit: 17
ath10k_pci 0000:03:00.0: Enabling feature bit: 18
ath10k_pci 0000:03:00.0: features
ath10k_pci 0000:03:00.0: 00000000: c0 77 07 00 00 00 00 00
Tested-by: NMike Lothian <mike@fireburn.co.uk>
Signed-off-by: NRyan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Immed relocation is missing a shift which means for larger
offsets the lower and higher part of the address would be
ORed together.

Fixes: ce4ebfd8 ("nfp: bpf: add helpers for updating immediate instructions")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

It was discovered that simple program which indefinitely sends 200b UDP
packets and runs on TI AM574x SoC (SMP) under RT Kernel triggers network
watchdog timeout in TI CPSW driver (<6 hours run). The network watchdog
timeout is triggered due to race between cpsw_ndo_start_xmit() and
cpsw_tx_handler() [NAPI]

cpsw_ndo_start_xmit()
	if (unlikely(!cpdma_check_free_tx_desc(txch))) {
		txq = netdev_get_tx_queue(ndev, q_idx);
		netif_tx_stop_queue(txq);

^^ as per [1] barier has to be used after set_bit() otherwise new value
might not be visible to other cpus
	}

cpsw_tx_handler()
	if (unlikely(netif_tx_queue_stopped(txq)))
		netif_tx_wake_queue(txq);

and when it happens ndev TX queue became disabled forever while driver's HW
TX queue is empty.

Fix this, by adding smp_mb__after_atomic() after netif_tx_stop_queue()
calls and double check for free TX descriptors after stopping ndev TX queue
- if there are free TX descriptors wake up ndev TX queue.

[1] https://www.kernel.org/doc/html/latest/core-api/atomic_ops.htmlSigned-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change will guard against a double free in the case that the
buffers were previously freed at some other time, such as during
a device reset. It resolves a kernel oops that occurred when changing
the VNIC device's MTU.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At some point, a check was added to exit the polling routine during resets.
This makes sense for most reset conditions, but for a non-fatal error, we
expect the polling routine to continue running to properly clean up the rx
queues. This patch checks if we are performing a non-fatal reset and if we
are, continues normal polling operation.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the appropriate SPDX license tags to the Sun network drivers
as outlined in Documentation/process/license-rules.rst.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit baf50868 ("cxgb4: restructure VF mgmt code") has reordered
some code but an error handling label has not been updated accordingly.
So fix it and free 'adapter' if 't4_wait_dev_ready()' fails.

Fixes: baf50868 ("cxgb4: restructure VF mgmt code")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as reported in:
https://github.com/qca/open-ath9k-htc-firmware/pull/71#issuecomment-361100070Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If device gone during chip reset, ar->normal_mode_fw.board is not
initialized, but ath10k_debug_print_hwfw_info() will try to access its
member, which will cause 'kernel NULL pointer' issue. This was found
using a faulty device (pci link went down sometimes) in a random
insmod/rmmod/other-op test.
To fix it, check ar->normal_mode_fw.board before accessing the member.

pci 0000:02:00.0: BAR 0: assigned [mem 0xf7400000-0xf75fffff 64bit]
ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
ath10k_pci 0000:02:00.0: failed to read device register, device is gone
ath10k_pci 0000:02:00.0: failed to wait for target init: -5
ath10k_pci 0000:02:00.0: failed to warm reset: -5
ath10k_pci 0000:02:00.0: firmware crashed during chip reset
ath10k_pci 0000:02:00.0: firmware crashed! (uuid 5d018951-b8e1-404a-8fde-923078b4423a)
ath10k_pci 0000:02:00.0: (null) target 0x00000000 chip_id 0x00340aff sub 0000:0000
ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
ath10k_pci 0000:02:00.0: firmware ver  api 0 features  crc32 00000000
...
BUG: unable to handle kernel NULL pointer dereference at 00000004
...
Call Trace:
 [<fb4e7882>] ath10k_print_driver_info+0x12/0x20 [ath10k_core]
 [<fb62b7dd>] ath10k_pci_fw_crashed_dump+0x6d/0x4d0 [ath10k_pci]
 [<fb629f07>] ? ath10k_pci_sleep.part.19+0x57/0xc0 [ath10k_pci]
 [<fb62c8ee>] ath10k_pci_hif_power_up+0x14e/0x1b0 [ath10k_pci]
 [<c10477fb>] ? do_page_fault+0xb/0x10
 [<fb4eb934>] ath10k_core_register_work+0x24/0x840 [ath10k_core]
 [<c18a00d8>] ? netlbl_unlhsh_remove+0x178/0x410
 [<c10477f0>] ? __do_page_fault+0x480/0x480
 [<c1068e44>] process_one_work+0x114/0x3e0
 [<c1069d07>] worker_thread+0x37/0x4a0
 [<c106e294>] kthread+0xa4/0xc0
 [<c1069cd0>] ? create_worker+0x180/0x180
 [<c106e1f0>] ? kthread_park+0x50/0x50
 [<c18ab4f7>] ret_from_fork+0x1b/0x28
 Code: 78 80 b8 50 09 00 00 00 75 5d 8d 75 94 c7 44 24 08 aa d7 52 fb c7 44 24 04 64 00 00 00
 89 34 24 e8 82 52 e2 c5 8b 83 dc 08 00 00 <8b> 50 04 8b 08 31 c0 e8 20 57 e3 c5 89 44 24 10 8b 83 58 09 00
 EIP: [<fb4e7754>]-
 ath10k_debug_print_board_info+0x34/0xb0 [ath10k_core]
 SS:ESP 0068:f4921d90
 CR2: 0000000000000004
Signed-off-by: NYu Wang <yyuwang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Commit 8da58553 ("ath9k: Use calibrated noise floor value
when available") introduced regression in ath9k_hw_getchan_noise
where per chain nominal noise floor has been taken instead default
for channel.
Revert to original default channel noise floor.

Fixes: 8da58553 ("ath9k: Use calibrated noise floor value when available")
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: NTobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1
are less than the actual value, some coredump contents are missed.
To fix it, change the length from 0x90000 to 0xa8000.

Fixes: 703f261d ("ath10k: add memory dump support for QCA6174/QCA9377")
Signed-off-by: NYu Wang <yyuwang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b163 ("rtlwifi: rtl8821ae: Fix connection
lost problem").

Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.

Fixes: b8b8b163 ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: NPkshih <pkshih@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org>  # x86_64 OLPC NL3
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If the driver receives a TX CQE with status as 0x1 or 0x9 or 0xb,
the completion indexes should not be used. The driver must stop
consuming CQEs from this TXQ/CQ. The TXQ from this point on-wards
to be in a bad state. Driver should destroy and recreate the TXQ.

0x1: LANCER_TX_COMP_LSO_ERR
0x9 LANCER_TX_COMP_SGE_ERR
0xb: LANCER_TX_COMP_PARITY_ERR

Reset the adapter if driver sees this error in TX completion. Also
adding sge error counter in ethtool stats.
Signed-off-by: NSuresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lancer HW cannot handle a TSO packet with a single segment.
Disable TSO/GSO for such packets.
Signed-off-by: NSuresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 84ce5b98 ("scripts: kernel-doc: improve nested logic to
handle multiple identifiers") improved the handling of nested structure
definitions in scripts/kernel-doc, and changed the expected format of
documentation.  This causes new warnings to appear on W=1 builds.

Only comment changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_GPIOLIB is disabled, fwnode_get_named_gpiod() becomes a stub
function, which return -ENOSYS. Handle this in the same way as
-ENOENT, i.e. assume there is no GPIO used to reset the PHYs.
Reported-by: NChristian Zigotzky <chzigotzky@xenosoft.de>
Tested-by: NChristian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Fixes: bafbdd52 ("phylib: Add device reset GPIO support")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>