- 20 5月, 2011 7 次提交
-
-
由 Florian Mickler 提交于
If we need a bigger buffer, we reallocte a new buffer and free the old one. Note: This change is tested to compile only as I don't have the hardware. Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Florian Mickler 提交于
Note: This change is tested to compile only as I don't have the hardware. Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Florian Mickler 提交于
Otherwise it is not obvious that vp702x_usb_in_op or vp702x_usb_out_op will not interfere with any vp702x_usb_inout_op. Note: This change is tested to compile only, as I don't have the hardware. Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Florian Mickler 提交于
usb_control_msg initiates (and waits for completion of) a dma transfer using the supplied buffer. That buffer thus has to be seperately allocated on the heap. In lib/dma_debug.c the function check_for_stack even warns about it: WARNING: at lib/dma-debug.c:866 check_for_stack Note: This change is tested to compile only, as I don't have the hardware. Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Florian Mickler 提交于
This sets up a buffer and a mutex protecting that buffer in the struct vp702x_device_state. The definition of struct vp702x_device_state is moved into the header in order to use the buffer also in the frontend. Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Florian Mickler 提交于
We need a state struct for the dvb_usb_device. In order to reduce confusion we rename the vp702x_state struct. Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Florian Mickler 提交于
Some whitespace, one linebreak and one unneded variable initialization... Signed-off-by: NFlorian Mickler <florian@mickler.org> Cc: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 29 12月, 2010 1 次提交
-
-
由 Mauro Carvalho Chehab 提交于
Remote keytables had different names all over the place. Part of the fault is due to a bad naming when rc subsystem was created, but there were lots of old names that were still here. Use a common standard for everything. Patch generated by this script: for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode,rc_map_table,g <$i >a && mv a $i; done for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_codes_,rc_map_,g <$i >a && mv a $i; done for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_key_map,rc_map_table,g <$i >a && mv a $i; done for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_map_table_size,rc_map_size,g <$i >a && mv a $i; done Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 03 8月, 2010 2 次提交
-
-
由 Mauro Carvalho Chehab 提交于
This is a big patch, yet trivial. It just move the RC properties to a separate struct, in order to prepare the dvb-usb drivers to use rc-core. There's no change on the behavior of the drivers. With this change, it is possible to have both legacy and rc-core based code inside the dvb-usb-remote, allowing a gradual migration to rc-core, driver per driver. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mauro Carvalho Chehab 提交于
dvb-usb has its own IR handle code. Now that we have a Remote Controller subsystem, we should start using it. So, remove this struct, in favor of the similar struct defined at the RC subsystem. This is a big, but trivial patch. It is a 3 line delect, plus lots of rename on several dvb-usb files. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 19 5月, 2010 1 次提交
-
-
由 Mauro Carvalho Chehab 提交于
Several DVB drivers use a different name convention. As we're moving the keytables, we need to use the same convention on all places. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 12 9月, 2009 1 次提交
-
-
由 Mauro Carvalho Chehab 提交于
In order to be closer to V4L IR implementation, it is needed to replace u8 custom, data to: u16 scan This allows using non-rc5 mappings, like the 8 bit keycodes used on older protocols. It will also allow future implementations of rc6 keystrokes when needed. Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 25 4月, 2008 1 次提交
-
-
由 Janne Grunau 提交于
The adapter_nr module options can be used to allocate static adapter numbers on a driver level. It avoids problems with changing DVB apapter numbers after warm/cold boot or device unplugging and repluging. Each driver holds DVB_MAX_ADAPTER long array of the preferred order of adapter numbers. options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a reversed allocation of adapter numbers. With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If both are already in use it will allocate the lowest free adapter number. Signed-off-by: NJanne Grunau <janne-dvb@grunau.be> Acked-by: NHermann Pitton <hermann.pitton@arcor.de> Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 26 1月, 2008 1 次提交
-
-
由 Adrian Bunk 提交于
This patch contains the following cleanups: - make the needlessly global vp702x_usb_out_op() static - #if 0 the unused vp702x_power_ctrl() Signed-off-by: NAdrian Bunk <bunk@kernel.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 10 12月, 2006 1 次提交
-
-
由 Patrick Boettcher 提交于
While converting everything to DVB-USB-Adapter, there was a wrong indention. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 04 10月, 2006 2 次提交
-
-
由 Patrick Boettcher 提交于
The fixed support for the VP70x (supports only StarBox2) is now in sync with latest changes in the dvb-usb framework. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Patrick Boettcher 提交于
This patch is the first commit of the Multiple Input Patch for the DVB-USB frame work. It changes the DVB-USB-device to be able to have more than one streaming input (e.g. multiple DVB-T sources) on one device. This is a necessary feature for the upcoming DiB7700 driven devices. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 07 2月, 2006 1 次提交
-
-
由 Ingo Molnar 提交于
Semaphore to mutex conversion. The conversion was generated via scripts, and the result was validated automatically via a script as well. Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 24 1月, 2006 2 次提交
-
-
由 Adrian Bunk 提交于
- Make needlessly global code static - #if 0 the following unused global functions: - b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq() - b2c2/flexcop-dma.c: flexcop_dma_config_packet_count() Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMichael Krufky <mkrufky@m1k.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
由 Adrian Bunk 提交于
- Make needlessly global code static - #if 0 the following unused global functions: - b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq() - b2c2/flexcop-dma.c: flexcop_dma_config_packet_count() Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NMichael Krufky <mkrufky@m1k.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
-
- 05 1月, 2006 1 次提交
-
-
由 Greg Kroah-Hartman 提交于
It is no longer needed, so let's remove it, saving a bit of memory. Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 10 9月, 2005 2 次提交
-
-
由 Patrick Boettcher 提交于
Change the init call to optionally return the new dvb_usb_device directly. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NJohannes Stezenbach <js@linuxtv.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Patrick Boettcher 提交于
Add driver for the TwinhanDTV StarBox and clones. Thanks to Ralph Metzler for his initial work on this box and thanks to Twinhan for their support. Signed-off-by: NPatrick Boettcher <pb@linuxtv.org> Signed-off-by: NJohannes Stezenbach <js@linuxtv.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-