This reverts the changed init order from commit 3647bc35
("dwc_eth_qos: Reset hardware before PHY start") and makes another fix
for the race.

It turned out that the reset state machine of the dwceqos hardware
requires PHY clocks to be present in order to complete the reset
cycle.

To plug the race with the phy state machine we defer link speed
setting until the hardware init has finished.
Signed-off-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since debug is hardcoded to 3, the defaults in the DWCEQOS_MSG_DEFAULT
macro are never used, which does not seem to be the intended behaviour
here.  Set debug to -1 like other drivers so that DWCEQOS_MSG_DEFAULT is
actually used by default.
Signed-off-by: NRabin Vincent <rabinv@axis.com>
Signed-off-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we are in non-atomic context here we can pass GFP_KERNEL to
dma_alloc_coherent(). This enables use of the CMA.
Signed-off-by: NRabin Vincent <rabinv@axis.com>
Signed-off-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prepare for using the CMA, we can not be in atomic context when
de-allocating DMA buffers.

The tx lock was needed only to protect the hw reset against the xmit
handler. Now we briefly grab the tx lock while stopping the queue to
make sure no thread is inside or will enter the xmit handler.
Signed-off-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The xmit handler and the tx_reclaim tasklet had a race on the tx_free
variable which could lead to a tx timeout if tx_free was updated after
the tx complete interrupt.
Signed-off-by: NRabin Vincent <rabinv@axis.com>
Signed-off-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF administrative mac addresses (stored in the PF driver) are
initialized to zero when the PF driver starts up.

These addresses may be modified in the PF driver through ndo calls
initiated by iproute2 or libvirt.

While we allow the PF/host to change the VF admin mac address from zero
to a valid unicast mac, we do not allow restoring the VF admin mac to
zero. We currently only allow changing this mac to a different unicast mac.

This leads to problems when libvirt scripts are used to deal with
VF mac addresses, and libvirt attempts to revoke the mac so this
host will not use it anymore.

Fix this by allowing resetting a VF administrative MAC back to zero.

Fixes: 8f7ba3ca ('net/mlx4: Add set VF mac address support')
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: NMoshe Levi <moshele@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The limit of 63 is only for virtual functions while the actual enforcement
was for VFs plus physical functions, fix that.

Fixes: e57968a1 ('net/mlx4_core: Support the HA mode for SRIOV VFs too')
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the mac and vlan register/unregister/replace functions, the driver locks
the mac table mutex (or vlan table mutex) on both ports.

We move to use mutex_lock_nested() to prevent warnings, such as the one below.

[ 101.828445] =============================================
[ 101.834820] [ INFO: possible recursive locking detected ]
[ 101.841199] 4.5.0-rc2+  #49 Not tainted
[ 101.850251] ---------------------------------------------
[ 101.856621] modprobe/3054 is trying to acquire lock:
[ 101.862514] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c10e>] __mlx4_register_mac+0x87e/0xa90 [mlx4_core]
[ 101.874598]
[ 101.874598] but task is already holding lock:
[ 101.881703] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c0f0>] __mlx4_register_mac+0x860/0xa90 [mlx4_core]
[ 101.893776]
[ 101.893776] other info that might help us debug this:
[ 101.901658] Possible unsafe locking scenario:
[ 101.901658]
[ 101.908859] CPU0
[ 101.911923] ----
[ 101.914985] lock(&table->mutex#2);
[ 101.919595] lock(&table->mutex#2);
[ 101.924199]
[ 101.924199] * DEADLOCK *
[ 101.924199]
[ 101.931643] May be due to missing lock nesting notation

Fixes: 5f61385d ('net/mlx4_core: Keep VLAN/MAC tables mirrored in multifunc HA mode')
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Suggested-by: NDoron Tsur <doront@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using the HW VPort counters for traffic (rx/tx packets/bytes)
statistics is wrong. This is because frames dropped due to steering or
out of buffer will be counted as received. To fix that, we move to use
the packet/bytes accounting done by the driver for what the netdev
reports out.

Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support [...]')
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sum up rx/tx bytes in software as we do for rx/tx packets, to be reported
in upcoming statistics fix.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon changing num_channels, reset the RSS indirection table to
match the new value.

Fixes: 2d75b2bc ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.

Fixes: 2d75b2bc ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.

The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
  holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
  Interrupt routine calls napi_schedule(), which triggers rx/tx
  skb process.
  An attempt to read SW timecounter using read_lock is done, which is
  already locked by a writer on the same CPU and cause soft lockup.

Add irqsave/irqrestore for when using the readers/writers lock for
writing.

Fixes: ef9814de ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.

Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.

Fixes: 5c50368f ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.

We revert this optimization.

Fixes: e586b3b0 ('net/mlx5: Ethernet Datapath files')
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate
message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002
address=0x0000000000003000 flags=0x0050] in dmesg.
Signed-off-by: NChunhao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a case of misleading code indentation.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency with other event data structs and to lessen
the chance of a mistake should one of the reserved fields become
used in the future, define the reserved fields as little-endian.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were no missing endianness conversions in this case, but the
fields of struct cfc_del_event_data should be defined as little-endian
to get rid of the ugly (__force __le32) casts.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not really a bug, but it was odd that bnx2x_eq_int() read the
message data as if it were a cfc_del_event regardless of the event type.
It's cleaner to access only the appropriate member of union event_data
after checking the event opcode.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ppc64 the PF did not receive messages from VFs correctly.

Fields of struct vf_pf_event_data are little-endian.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF is sending a message to the PF, it needs to trigger the PF
to tell it the message is ready.
The trigger did not work on ppc64. No interrupt appeared in the PF.

The bug is due to confusion about the layout of struct trigger_vf_zone.
In bnx2x_send_msg2pf() the trigger is written using writeb(), not
writel(), so the attempt to define the struct with a reversed layout on
big-endian is counter-productive.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x crashes during the initialization of the 8021q module on ppc64.
The bug is a missing conversion from le32 in
bnx2x_handle_classification_eqe() when obtaining the cid value from
struct eth_event_data.

The fields in struct eth_event_data should all be declared as
little-endian and conversions added where missing.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use list_move_tail() to move MAC address entry from list of pending
to list of active entries. Simple list_add_tail() leaves the entry
also in the first list, this leads to list corruption.

Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NRasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently, I fixed a bug in 3c59x:

commit 6e144419
Author: Neil Horman <nhorman@tuxdriver.com>
Date:   Wed Jan 13 12:43:54 2016 -0500

    3c59x: fix another page map/single unmap imbalance

Which correctly rebalanced dma mapping and unmapping types.  Unfortunately it
introduced a new bug which causes oopses on older systems.

When mapping dma regions, the last entry for a packet in the 3c59x tx ring
encodes a LAST_FRAG bit, which is encoded as the high order bit of the buffers
length field.  When it is unmapped the LAST_FRAG bit is cleared prior to being
passed to the unmap function.  Unfortunately the commit above fails to do that
masking.  It was missed in testing because the system on which I tested it had
an intel iommu, the driver for which ignores the size field, using only the DMA
address as the token to identify the mapping to be released.  However, on older
systems that rely on swiotlb (or other dma drivers that key off that length
field), not masking off that LAST_FRAG high order bit results in parsing a huge
size to be release, leading to all sorts of odd corruptions and the like.

Fix is easy, just mask the length with 0xFFF.  It should really be
&(LAST_FRAG-1), but 0xFFF is the style of the file, and I'd like to make this
fix minimal and correct before making it prettier.

Appies to the net tree cleanly.  All testing on both iommu and swiommu based
systems produce good results
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.

This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: NJerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There will be a log spam when there is no cable plugged. Please refer to
following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351
https://bugzilla.kernel.org/show_bug.cgi?id=107421

This issue is caused by runtime power management. When there is no cable
plugged, the driver will be suspend (runtime suspend) by OS and NIC will be
put into the D3 state. During this time, if OS call rtl8169_get_stats64()
to dump tally counter, because NIC is in D3 state, the register value read
by driver will return all 0xff. This will let driver think tally counter
flag is not toggled and then sends the warning message "rtl_counters_cond
== 1 (loop: 1000, delay: 10)" to kernel log.

For fixing this issue, 1.add checking driver's pm runtime status in
rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend
for counter accuracy in runtime suspend.
Signed-off-by: NChunhao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: NMichael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.

Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.

Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351Signed-off-by: NDiego Viola <diego.viola@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.

https://stackoverflow.com/questions/31046172/device-tree-for-phy-less-connection-to-a-dsa-switch

This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: NSebastian Frias <sf84@laposte.net>
Acked-by: NMans Rullgard <mans@mansr.com>
Cc: Mason <slash.tmp@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The arithmetic to zero pad the last 64-bit word in the push buffer is not
correct.

1. It should be pdata + length to get to the end.
2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the
aligned pointer to void.  Pass 'end' which is u64 pointer to PTR_ALIGN()
instead so that the aligned pointer - 1 is the last 64-bit pointer to data.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current initialization sequence is lacking, causing some configurations
to fail.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy's firmware version isn't being parsed properly as it's
currently parsed like the rest of the 848xx phys.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when link is using KR2 it cannot be forced to any speed other
than 20g.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.om>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dm9000 driver doesn't work in at least one device-tree
configuration, spitting an error message on irq resource :
[    1.062495] dm9000 8000000.ethernet: insufficient resources
[    1.068439] dm9000 8000000.ethernet: not found (-2).
[    1.073451] dm9000: probe of 8000000.ethernet failed with error -2

The reason behind is that the interrupt might be provided by a gpio
controller, not probed when dm9000 is probed, and needing the probe
deferral mechanism to apply.

Currently, the interrupt is directly taken from resources. This patch
changes this to use the more generic platform_get_irq(), which handles
the deferral.

Moreover, since commit Fixes: 7085a740 ("drivers: platform: parse
IRQ flags from resources"), the interrupt trigger flags are honored in
platform_get_irq(), so remove the needless code in dm9000.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMarcel Ziswiler <marcel@ziswiler.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: NSergei Ianovich <ynvich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix incorrect indexing of dev->dev_addr[] when copying the MAC address
of FMV-J182 at buf[5].
Signed-off-by: NKen Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>