- 03 3月, 2016 28 次提交
-
-
由 David S. Miller 提交于
Lars Persson says: ==================== dwc_eth_qos: stability fixes and support for CMA This series has bug fixes for the dwc_eth_qos ethernet driver. Mainly two stability fixes for problems found by Rabin Vincent: - Successive starts and stops of the interface would trigger a DMA reset timeout. - A race condition in the TX DMA handling could trigger a netdev watchdog timeout. The memory allocation was improved to support use of the CMA as DMA allocator backend. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Lars Persson 提交于
This reverts the changed init order from commit 3647bc35 ("dwc_eth_qos: Reset hardware before PHY start") and makes another fix for the race. It turned out that the reset state machine of the dwceqos hardware requires PHY clocks to be present in order to complete the reset cycle. To plug the race with the phy state machine we defer link speed setting until the hardware init has finished. Signed-off-by: NLars Persson <larper@axis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rabin Vincent 提交于
Since debug is hardcoded to 3, the defaults in the DWCEQOS_MSG_DEFAULT macro are never used, which does not seem to be the intended behaviour here. Set debug to -1 like other drivers so that DWCEQOS_MSG_DEFAULT is actually used by default. Signed-off-by: NRabin Vincent <rabinv@axis.com> Signed-off-by: NLars Persson <larper@axis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rabin Vincent 提交于
Since we are in non-atomic context here we can pass GFP_KERNEL to dma_alloc_coherent(). This enables use of the CMA. Signed-off-by: NRabin Vincent <rabinv@axis.com> Signed-off-by: NLars Persson <larper@axis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Lars Persson 提交于
To prepare for using the CMA, we can not be in atomic context when de-allocating DMA buffers. The tx lock was needed only to protect the hw reset against the xmit handler. Now we briefly grab the tx lock while stopping the queue to make sure no thread is inside or will enter the xmit handler. Signed-off-by: NLars Persson <larper@axis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rabin Vincent 提交于
The xmit handler and the tx_reclaim tasklet had a race on the tx_free variable which could lead to a tx timeout if tx_free was updated after the tx complete interrupt. Signed-off-by: NRabin Vincent <rabinv@axis.com> Signed-off-by: NLars Persson <larper@axis.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Or Gerlitz says: ==================== Mellanox 10/40G mlx4 driver fixes for 4.5-rc6 This series contains two fixes for the SRIOV HW LAG that was introduced in 4.5-rc1 and one fix that allows to revoke the administrative MAC that was assigned to VF through the PF. The VF mac fix needs to go for stable too. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
The VF administrative mac addresses (stored in the PF driver) are initialized to zero when the PF driver starts up. These addresses may be modified in the PF driver through ndo calls initiated by iproute2 or libvirt. While we allow the PF/host to change the VF admin mac address from zero to a valid unicast mac, we do not allow restoring the VF admin mac to zero. We currently only allow changing this mac to a different unicast mac. This leads to problems when libvirt scripts are used to deal with VF mac addresses, and libvirt attempts to revoke the mac so this host will not use it anymore. Fix this by allowing resetting a VF administrative MAC back to zero. Fixes: 8f7ba3ca ('net/mlx4: Add set VF mac address support') Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Reported-by: NMoshe Levi <moshele@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Moni Shoua 提交于
The limit of 63 is only for virtual functions while the actual enforcement was for VFs plus physical functions, fix that. Fixes: e57968a1 ('net/mlx4_core: Support the HA mode for SRIOV VFs too') Signed-off-by: NMoni Shoua <monis@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
In the mac and vlan register/unregister/replace functions, the driver locks the mac table mutex (or vlan table mutex) on both ports. We move to use mutex_lock_nested() to prevent warnings, such as the one below. [ 101.828445] ============================================= [ 101.834820] [ INFO: possible recursive locking detected ] [ 101.841199] 4.5.0-rc2+ #49 Not tainted [ 101.850251] --------------------------------------------- [ 101.856621] modprobe/3054 is trying to acquire lock: [ 101.862514] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c10e>] __mlx4_register_mac+0x87e/0xa90 [mlx4_core] [ 101.874598] [ 101.874598] but task is already holding lock: [ 101.881703] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c0f0>] __mlx4_register_mac+0x860/0xa90 [mlx4_core] [ 101.893776] [ 101.893776] other info that might help us debug this: [ 101.901658] Possible unsafe locking scenario: [ 101.901658] [ 101.908859] CPU0 [ 101.911923] ---- [ 101.914985] lock(&table->mutex#2); [ 101.919595] lock(&table->mutex#2); [ 101.924199] [ 101.924199] * DEADLOCK * [ 101.924199] [ 101.931643] May be due to missing lock nesting notation Fixes: 5f61385d ('net/mlx4_core: Keep VLAN/MAC tables mirrored in multifunc HA mode') Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Suggested-by: NDoron Tsur <doront@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Saeed Mahameed says: ==================== Mellanox 100G mlx5 driver fixes This series has few bug fixes for the mlx5 Ethernet driver. Eran fixed a locking issue with time-stamping that could cause a soft-lockup when time-stamping is enabled. Gal fixed the rx/tx packets/bytes counters returned by the driver to actually went through the network stack. Tariq removed a poll CQ optimization which could lead the driver to stop getting interrupts for some of the rings, and a did also fix to HW LRO which is currently broken. He also provided RSS and RX hash fixes for the case of changing the number of rx rings the RX hash/RSS configuration will be out of sync. The time stamping fix from Eran is not for -stable as the feature was only introduced in 4.5 but all of the others are. Changes fro V0: - Eran addressed the irqsave/restore comments from "Dave" and fixed them. This series is generated against net commit 4c0b6eaf 'net: thunderx: Fix for Qset error due to CQ full' ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gal Pressman 提交于
Using the HW VPort counters for traffic (rx/tx packets/bytes) statistics is wrong. This is because frames dropped due to steering or out of buffer will be counted as received. To fix that, we move to use the packet/bytes accounting done by the driver for what the netdev reports out. Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support [...]') Signed-off-by: NGal Pressman <galp@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Gal Pressman 提交于
Sum up rx/tx bytes in software as we do for rx/tx packets, to be reported in upcoming statistics fix. Signed-off-by: NGal Pressman <galp@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tariq Toukan 提交于
Upon changing num_channels, reset the RSS indirection table to match the new value. Fixes: 2d75b2bc ('net/mlx5e: Add ethtool RSS configuration options') Signed-off-by: NTariq Toukan <tariqt@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tariq Toukan 提交于
We should modify TIRs explicitly to apply the new RSS configuration. The light ndo close/open calls do not "refresh" them. Fixes: 2d75b2bc ('net/mlx5e: Add ethtool RSS configuration options') Signed-off-by: NTariq Toukan <tariqt@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eran Ben Elisha 提交于
Readers/Writers lock for SW timecounter was acquired without disabling interrupts on local CPU. The problematic scenario: * HW timestamping is enabled * Timestamp overflow periodic service task is running on local CPU and holding write_lock for SW timecounter * Completion arrives, triggers interrupt for local CPU. Interrupt routine calls napi_schedule(), which triggers rx/tx skb process. An attempt to read SW timecounter using read_lock is done, which is already locked by a writer on the same CPU and cause soft lockup. Add irqsave/irqrestore for when using the readers/writers lock for writing. Fixes: ef9814de ('net/mlx5e: Add HW timestamping (TS) support') Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tariq Toukan 提交于
Ethtool LRO enable/disable is broken, as of today we only modify TCP TIRs in order to apply the requested configuration. Hardware requires that all TIRs pointing to the same RQ should share the same LRO configuration. For that all other TIRs' LRO fields must be modified as well. Fixes: 5c50368f ('net/mlx5e: Light-weight netdev open/stop') Signed-off-by: NTariq Toukan <tariqt@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tariq Toukan 提交于
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy flow might occur: - Suppose RX is always busy, TX has a single packet every second. - We poll a single TX cqe and clear its flag. - We never arm it again as RX is always busy. - TX CQ flag is never changed, and new TX cqes are not polled. We revert this optimization. Fixes: e586b3b0 ('net/mlx5: Ethernet Datapath files') Signed-off-by: NTariq Toukan <tariqt@mellanox.com> Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Chunhao Lin 提交于
For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002 address=0x0000000000003000 flags=0x0050] in dmesg. Signed-off-by: NChunhao Lin <hau@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'mac80211-for-davem-2016-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Here are a few more fixes for the current cycle: * check GCMP encryption vs. fragmentation properly; we'd found this problem quite a while ago but waited for the 802.11 spec to be updated * fix RTS/CTS logic in minstrel_ht * fix RX of certain public action frames in AP mode * add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps the kbuild robot pick up the right tree for it ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Michal Schmidt says: ==================== bnx2x: endianness fixes this fixes a VLAN crash and some SRIOV bugs in bnx2x observed on ppc64. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
Fix a case of misleading code indentation. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
For consistency with other event data structs and to lessen the chance of a mistake should one of the reserved fields become used in the future, define the reserved fields as little-endian. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
There were no missing endianness conversions in this case, but the fields of struct cfc_del_event_data should be defined as little-endian to get rid of the ugly (__force __le32) casts. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
It's not really a bug, but it was odd that bnx2x_eq_int() read the message data as if it were a cfc_del_event regardless of the event type. It's cleaner to access only the appropriate member of union event_data after checking the event opcode. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
On ppc64 the PF did not receive messages from VFs correctly. Fields of struct vf_pf_event_data are little-endian. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
When a VF is sending a message to the PF, it needs to trigger the PF to tell it the message is ready. The trigger did not work on ppc64. No interrupt appeared in the PF. The bug is due to confusion about the layout of struct trigger_vf_zone. In bnx2x_send_msg2pf() the trigger is written using writeb(), not writel(), so the attempt to define the struct with a reversed layout on big-endian is counter-productive. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michal Schmidt 提交于
bnx2x crashes during the initialization of the 8021q module on ppc64. The bug is a missing conversion from le32 in bnx2x_handle_classification_eqe() when obtaining the cid value from struct eth_event_data. The fields in struct eth_event_data should all be declared as little-endian and conversions added where missing. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 3月, 2016 10 次提交
-
-
由 Johannes Berg 提交于
Since I maintain this driver as part of mac80211, add it to the file list for mac80211; this helps submitters send it to me instead of Kalle and also makes the build robot apply the patches for it on the right tree for build attempts. Acked-by: NKalle Valo <kvalo@codeaurora.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sergei Shtylyov 提交于
The 'flags' parameter of the of_phy_connect() function wasn't described in the kernel-doc comment... Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
Now in sctp_remaddr_seq_show(), we use variable *tsp to get the param *v. but *tsp is also used to traversal transport_addr_list, which will cover the previous value, and make sctp_transport_put work on the wrong transport. So fix it by adding a new variable to get the param *v. Fixes: fba4c330 ("sctp: hold transport before we access t->asoc in sctp proc") Signed-off-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by sctp_cmp_addr_exact(). Now sctp_v6_cmp_addr just check the port when two addresses have different family, and lack the port check for two ipv6 addresses. that will make sctp_hash_cmp() cannot work well. so fix it by adding ports comparison in sctp_v6_cmp_addr(). Signed-off-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Alexandre Belloni says: ==================== phy: micrel: fix issues with interrupt on atmel boards Since the phy is not polled anymore, there were issues getting a link on the sama5d* xplained boards. I'm not too sure about were those fixes should go and I'm wondering whether the first one shoud be made generic. For the second one, I found the PHY_HAS_MAGICANEG flag that is not used and I wondering whether this is related to that kind of issue. I had a quick look at the history and could'nt find its use. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexandre Belloni 提交于
Disable auto negotiation on init to properly detect an already plugged cable at boot. At boot, when the phy is started, it is in the PHY_UP state. However, if a cable is plugged at boot, because auto negociation is already enabled at the time we get the first interrupt, the phy is already running. But the state machine then switches from PHY_UP to PHY_AN and calls phy_start_aneg(). phy_start_aneg() will not do anything because aneg is already enabled on the phy. It will then wait for a interrupt before going further. This interrupt will never happen unless the cable is unplugged and then replugged. It was working properly before 321beec5 (net: phy: Use interrupts when available in NOLINK state) because switching to NOLINK meant starting polling the phy, even if IRQ were enabled. Fixes: 321beec5 (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexandre Belloni 提交于
At least on ksz8081, when getting back from power down, interrupts are disabled. ensure they are reenabled if they were previously enabled. This fixes resuming which is failing on the xplained boards from atmel since 321beec5 (net: phy: Use interrupts when available in NOLINK state) Fixes: 321beec5 (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guillaume Nault 提交于
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl(). In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update ppp->flags while ppp_read() or ppp_poll() is reading it. The update done by ppp_ccp_closed() isn't atomic due to the bit mask operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent readers might get transient values. Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC' test in ppp_read() and ppp_poll(), which in turn can lead to improper decision on whether the PPP unit file is ready for reading or not. Since ppp_ccp_closed() is protected by the Rx and Tx locks (with ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll() to guarantee that ppp_ccp_closed() won't update ppp->flags concurrently. The same reasoning applies to ppp->n_channels. The 'n_channels' field can also be written to concurrently by ppp_ioctl() (through ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't atomic (simple increment/decrement), but are protected by both the Rx and Tx locks (like in the ppp->flags case). So holding the Rx lock before reading ppp->n_channels also prevents concurrent writes. Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Vecera 提交于
Use list_move_tail() to move MAC address entry from list of pending to list of active entries. Simple list_add_tail() leaves the entry also in the first list, this leads to list corruption. Cc: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: NIvan Vecera <ivecera@redhat.com> Acked-by: NRasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'linux-can-fixes-for-4.5-20160226' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2016-02-26 this is a pull request of one patch for net. The patch by Maximilain Schneider fixes a kfree() problem during disconnect in the gs_usb driver. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 3月, 2016 2 次提交
-
-
由 Felix Fietkau 提交于
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's a dual-stream rate and the sta is in dynamic SMPS mode. Cc: stable@vger.kernel.org Fixes: a3ebb4e1 ("mac80211: minstrel_ht: handle peers in dynamic SMPS") Reported-by: NMatías Richart <mrichart@fing.edu.uy> Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Jouni Malinen 提交于
Public Action frames use special rules for how the BSSID field (Address 3) is set. A wildcard BSSID is used in cases where the transmitter and recipient are not members of the same BSS. As such, we need to accept Public Action frames with wildcard BSSID. Commit db8e1732 ("mac80211: ignore frames between TDLS peers when operating as AP") added a rule that drops Action frames to TDLS-peers based on an Action frame having different DA (Address 1) and BSSID (Address 3) values. This is not correct since it misses the possibility of BSSID being a wildcard BSSID in which case the Address 1 would not necessarily match. Fix this by allowing mac80211 to accept wildcard BSSID in an Action frame when in AP mode. Fixes: db8e1732 ("mac80211: ignore frames between TDLS peers when operating as AP") Cc: stable@vger.kernel.org Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-