When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.

Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.

This patch fixes a bug introduced by:
d9663c8c ("amd-xgbe-phy: Use phydev advertising field vs supported")
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, there is no interrupt code that indicates auto-negotiation
has timed out. If the auto-negotiation has timed out then the start of
a new auto-negotiation will begin again with a new base page being
received. The state machine could be in a state that is not expecting
this interrupt code which results in an error during auto-negotiation.

Update the code to timestamp when the auto-negotiation starts.  Should
another page received interrupt code occur before auto-negotiation has
completed but after the auto-negotiation timeout, then reset the state
machine to allow the auto-negotiation to continue.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the setting of the transceiver type when retrieving the device
settings using ethtool and instead set the transceiver type in the
phy_driver structure flags field. Change the transceiver type to be
internal, also.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With ethtool being able to control what is advertised, the advertising
field is what should be used for priming the auto-negotiation registers
and for various other checks, instead of the supported field.

Also, move the initial setting of the supported and advertising fields
into the probe function so that they are not reset each time the device
is brought up, thus allowing the user to set as desired before bringing
the device up.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY requires different settings for the Decision Feedback Analyzer
(DFE) when running in KX mode vs. KR mode. Update the code to change
these settings when changing modes in order to provide a more stable
link.

Additionally, adjust the 10GbE PQ skew default setting to a more sane
value.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Certain PHY settings need to be configurable by UEFI depending on the
platform being used.  Add new device tree / ACPI properties that, if
present, will override the pre-determined values currently used.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for ACPI to the amd-xgbe and amd-xgbe-phy drivers. This
support converts many of the device tree APIs to the new device_property
APIs.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When receiving and processing extended next pages the base registers
were used instead of the XNP registers. Update the code to use the
device XNP and link partner XNP registers.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Advertise and apply the Forward Error Correction capabilities of the
device based on the FEC ability of the device. Also, remove the use
of some hard coded values related to KR and FEC in preference of some
#defines.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reads to registers are undefined when the PCS is powered down. To be
safe, save the CTRL1 register used for power down during suspend and
restore that value during resume.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.

Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to sync the states of the PCS and the PHY
after a reset is performed.  If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A previous patch inadvertently deleted a declaration in the
amd_xgbe_an_tx_training function causing the build to fail.

Add the declaration for 'priv' back to the function.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is.  Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present.  Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the logic will loop endlessly waiting for a rate change
to complete.  Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix following compilation warning:
[...]
  CC      drivers/net/phy/amd-xgbe-phy.o
drivers/net/phy/amd-xgbe-phy.c:1353:30: warning:
‘amd_xgbe_phy_ids’ defined but not used [-Wunused-variable]
 static struct mdio_device_id amd_xgbe_phy_ids[] = {
                              ^
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides the initial phylib driver in support
of the AMD 10GbE device.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>