- 23 7月, 2008 40 次提交
-
-
由 Alan Cox 提交于
I missed the cpm_uart one. Thanks to Kumar Gala for reporting it. A double check found samsung also needed fixing up. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
The ldisc needs to be referenced properly when used. The tty layer has a helper for this which should have been used but this driver got missed originally. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Fix locking in error path of rx_enable() introduced by synclink_gt-add-rx-dma-buffer-fill-level-control patch. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Add run time control for receive DMA buffer fill level to allow application to control receive latency when using stream oriented serial protocols that pass receive data to application only after a DMA buffer fills. This was previously a compile time option, but run time control is needed when application changes data rate (and latency requirements) or uses different data rates on different ports. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Leave the transmitter in reset state after configuration so that transmit signal is held at mark until transmitter is explicitly enabled by application, otherwise transmitter sends idle pattern. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Improve the accuracy of TIOCOUTQ value as implemented in chars_in_buffer() method by walking and counting tx DMA buffers, reading controller tx FIFO level and accounting for controller tx shift register. The greatly improves application control of transmit latency at lower data rates. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Add control of hardware serial bit order between LSB first (default/standard) and MSB first. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Improve write method by allowing multiple HDLC frames to be loaded into tx DMA buffer ring for continuous frame transmission. This simplifies the transmit code by using the common procedures for all serial protocols. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Fulghum 提交于
Make n_hdlc line discipline honor the O_NONBLOCK file flag on write. Signed-off-by: NPaul Fulghum <paulkf@microgate.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Anton Vorontsov 提交于
With SMP kernels _irqsave spinlock disables only local interrupts, while the shared serial interrupt could be assigned to the CPU that is not currently starting up the serial port. This might cause issues because serial8250_startup() routine issues IRQ-triggering operations before registering the port in the IRQ chain (though, this is fine to do and done explicitly because we don't want to process any interrupts on the port startup). With RT kernels and preemptable hardirqs, _irqsave spinlock does not disable local hardirqs, and the bug could be reproduced much easily: $ cat /dev/ttyS0 & $ cat /dev/ttyS1 irq 42: nobody cared (try booting with the "irqpoll" option) Call Trace: [C0475EB0] [C0008A98] show_stack+0x4c/0x1ac (unreliable) [C0475EF0] [C004BBD4] __report_bad_irq+0x34/0xb8 [C0475F10] [C004BD38] note_interrupt+0xe0/0x308 [C0475F50] [C004B09C] thread_simple_irq+0xdc/0x104 [C0475F70] [C004B3FC] do_irqd+0x338/0x3c8 [C0475FC0] [C00398E0] kthread+0xf8/0x100 [C0475FF0] [C0011FE0] original_kernel_thread+0x44/0x60 handlers: [<c02112c4>] (serial8250_interrupt+0x0/0x138) Disabling IRQ #42 After this, all serial ports on the given IRQ are non-functional. To fix the issue we should explicitly disable shared IRQ before issuing any IRQ-triggering operations. I also changed spin_lock_irqsave to the ordinary spin_lock, since it seems to be safe: chain does not contain new port (yet), thus nobody will interfere us from the ISRs. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Howells 提交于
Fix the epca driver to call epca_setup() if digiepca=xxx is included on the command line and the epca driver is built in. epca_setup() used to be called from init/main.c in 2.2 kernels, but somewhere along the way that call was removed but not replaced. Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jiri Slaby 提交于
Add support for CP-102UF moxa card (update to 1.12 original driver) and increment this driver version. (Somewhat reworked by alan@redhat.com to merge in with other patches) Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Use the hardware break support on the specialix driver Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Howells 提交于
Fix the Stallion driver's putchar() and break_ctl() ops and iStallion's putchar() to return values. Is it actually possible for putchar() or break_ctl() to be called with tty == NULL or can the check be discarded? Should stl_write() be returning 0 if tty->driver_data is NULL or tx.buf is NULL? Is this even possible? I've made Stallion's functions return -EINVAL as stli_breakctl() if the checks fail. Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Convert the driver to use the added hardware break support Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Some hardware needs to do break handling itself and may have partial support only. Make break_ctl return an error code. Add a tty driver flag so you can indicate driver hardware side break support. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Nobody seems to use these drivers anyway so if they want them they can fix them up. I don't have the needed info to add break_ctl support to them. Send patches if you don't like it. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Old style ioctl break code can go Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
The ioctls it talks about are midlayer provided. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Go through the inlines and other oddments that are iffy. Remove various bits of dead code and bogus debug. Turn the crtsdts compile time option into a runtime switch. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Preparation for doing some real work on the driver. Do this first so we can easily identify if the cleanups accidentally broke something Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
The edgeport reports negative error codes to functions that do not expect them. This can cause ports to jam forever Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-