Inclusion of a WPS IE in probe requests caused a problem
in the driver due to the maximum size of the probe request
template and the max_scan_ie_len values at initialization.

Increased the size of probe request template
to the maximum size allowed by the firmware.
Struct wl12xx_probe_req_template, which was only used
for calculating the max size of the probe request template,
is no longer used and needed.

max_scan_ie_len is used for validating the size of
additional IEs in scan requests.
Initialized the max_scan_ie_len field to the maximum size
of the probe request template minus the ieee80211 header size.
Signed-off-by: NGuy Eilam <guy@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

The auto-arp feature of wl12xx allows the firmware to automatically
response to arp requests asking for its ip.

in order to use it, we configure the arp response template and
enable the corresponding bit in wl1271_acx_arp_filter (along with
passing its ip)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

This module enables individually generating RX and TX traffic
over the SDIO bus on which the WL1271 chipset is connected.
This is required to perform RF interference testing.

The module takes 2 module parameters 'rx' and 'tx'.

To generate RX traffic:
	modprobe wl1271_sdio_test rx=1
To generate TX traffic:
	modprobe wl1271_sdio_test tx=1

To generate both RX & TX traffic, set both rx and tx to 1.

You can change the testing configuration at runtime by changing
the rx & tx values at /sys/modules/wl1271_sdio_test/

To stop testing simply unload the module.
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Reviewed-by: NCarlos Chinea <carlos.chinea@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Disabling the 11a channels when not supported in the reg_notify function was
not working as it should, because when the driver is initiailizing (and
registering itself with mac80211), it would get the reg notification too
early.  At that point the driver wouldn't have received the NVS yet, so it
wouldn't know whether 11a was supported.

To fix this, we disable 11a channels when we read the NVS instead.  Also, it
is easier (and still safe) to set n_channels to zero instead of setting the
disabled flag on every 11a channel.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Because we don't support them at this stage.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

For the SDIO testing module we need to load the firmware but not
boot it. wl1271_load_firmware() is meant to do just the firmware loading part.

We also export some functions so they are usable in the testing module.
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

If we try to reset the debugfs statistics when debugfs is not configured in
the kernel, we're memset an illegal pointer, because it has never been
allocated.  So check whether we have debugfs enabled by looking into the
wl->rootdir before trying to reset the fw_stats struct.
Reported-by: NJoerie de Gram <j.de.gram@gmail.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Use per-device debugfs path, so multiple devices won't collide.

in order to use wl->hw->wiphy->debugfsdir, we have to move the debugfs
creation from wl1271_debugfs_init() to wl1271_register_hw().
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Documentation/filesystems/debugfs.txt:
"""
Once upon a time, debugfs users were required to remember the dentry pointer
for every debugfs file they created so that all files could be cleaned up.
We live in more civilized times now, though, and debugfs users can call:

    void debugfs_remove_recursive(struct dentry *dentry);
"""
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

The probe-request template used in the hardware connection monitoring feature
thus far has been an empty one, without the SSID IE and without supported rate
IEs. This causes problems with some AP's.

Additionally, after connected scans, the template for connection maintenance
would remain to be the one last used for scanning - potentially incorrect.

Fix these by getting a pre-filled directed probe-request template for the
associated-to AP from mac80211.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Instead of simply not scanning for the 11a channels when not supported by the
hardware, disable the channels in reg_notify.  This centralizes the decision
on whether to scan 5GHz channel in one place and allows userspace to know
exactly which channels are in use.

Based on Juuso Oikarinen's idea.

Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>

It is possible that the op_remove_interface function  is invoked exactly at
the same time has hw recovery is started. In this case it is possible for the
interface to be already removed in the op_remove_interface call, which
currently leads to a kernel warning and a subsequent kernel crash.

Fix this by ignoring the op_remove_interface call if the interface is already
down at that point.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: NTuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

On the disassociation event from the mac80211, the wl12xx driver does not
clear the chipset configuration related to the AP - i.e. it does not perform
a DISCONNECT and then a JOIN with zero SSID and dummy BSSID. Also, it does not
unset the BSSID filter.

Often this is not a problem, as the above is performed upon entering idle
state. But if a scenario arises where a new association is attempted without
cycling through idle state, the new association will fail.

Fix this by resetting the firmware state on disassociation.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

Indicate to mac80211 we support HW fragmentation.
Support updates of the fragmentation threshold via the
set_frag_threshold callback.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

This reverts commit fa21c7a9.

The reverted patch caused more harm than benefit.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Tested-by: NTuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

The wl1271 does not support radar detection. Hence, prevent ad-hoc and
active scanning on frequencies requiring DFS.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: NTuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

The cleanup unused code for calibration procedures.
Signed-off-by: NGery Kahn <geryk@ti.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

This hacks leads to incorrect SPROM parsing for me and reading for example MAC
as: 00:00:00:54:00:00. Michael G. who introduced this confirmed it is not
needed anymore.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Tested-by: NMichael Gerdau <mgd@qata.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Embedded boards do not have compressed EEPROM data, they use the
struct ar9003_eeprom layout, with little endian fields, so copying
the raw data to the eeprom buffer is enough.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some embedded boards store platform data for connected PCIe AR92xx
chips in the system flash instead of a separate EEPROM chip.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  CC [M]  drivers/net/wireless/rndis_wlan.o
drivers/net/wireless/rndis_wlan.c: In function ‘rndis_wlan_craft_connected_bss’:
drivers/net/wireless/rndis_wlan.c:2542:2: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>

  CC [M]  drivers/net/wireless/iwmc3200wifi/commands.o
drivers/net/wireless/iwmc3200wifi/commands.c: In function ‘iwm_scan_ssids’:
drivers/net/wireless/iwmc3200wifi/commands.c:911:15: warning: operation on ‘iwm->scan_id’ may be undefined
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.

This uses the recently added generic EWMA library function.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove ath5k's private moving average implementation in favour of the generic
library version.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds generic functions for calculating Exponentially Weighted Moving
Averages (EWMA). This implementation makes use of a structure which keeps the
EWMA parameters and a scaled up internal representation to reduce rounding
errors.

The original idea for this implementation came from the rt2x00 driver
(rt2x00link.c). I would like to use it in several places in the mac80211 and
ath5k code and I hope it can be useful in many other places in the kernel code.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code to handle powersaving stations has a race:
when the powersave flag is lifted from a station,
we could transmit a packet that is being processed
for TX at the same time right away, even if there
are other frames queued for it. This would cause
frame reordering. To fix this, lift the flag only
under the appropriate lock that blocks TX.

Additionally, the code to allow drivers to block a
station while frames for it are on the HW queue is
never re-enabled the station, so traffic would get
stuck indefinitely. Fix this by clearing the flag
for this appropriately.

Finally, as an optimisation, don't do anything if
the driver unblocks an already unblocked station.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In many places we've just hardcoded the
AC numbers -- which is a relic from the
original mac80211 (d80211). Add constants
for them so we know what we're talking
about.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the new AR9003 cards do not come with an external EEPROM chip
anymore. Calibration data on these cards is stored in the OTP ROM on
the chip.
This patch adds support for reading this data, and also adds support
for different EEPROM chip sizes (512 bytes instead of 1K).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the pointers after the rates in the tx info cannot be used anymore
after frames have been queued, this area can be used to store information
that was previously stored in the ath_buf. With these changes, we can delay
the ath_buf assignment in the aggregation code until aggregates are formed.

That will not only make it possible to simplify DMA descriptor setup to
do less rewriting of uncached memory, but will also make it easier to
move aggregation out of the core of the ath9k tx path.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- remove the BUF_HT flag, and instead check for IEEE80211_TX_CTL_AMPDU
  before calling ath_tx_send_ampdu.
- remove a few unused variables
- calculate frame length before adding the frame padding
- merge the misnamed ath_tx_start_dma function into ath_tx_start
- remove an unused argument for assign_aggr_tid_seqno
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes further tx path cleanups easier
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge initial processing for the CAB queue and regular tx.
Also move ath_tx_cabq() to beacon.c and make it static.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>