* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
  cxgb3: Fix crash caused by stashing wrong netdev_queue
  ixgbe: Fix coexistence of FCoE and Flow Director in 82599
  memory barrier: adding smp_mb__after_lock
  net: adding memory barrier to the poll and receive callbacks
  netpoll: Fix carrier detection for drivers that are using phylib
  includecheck fix: include/linux, rfkill.h
  p54: tx refused but queue active
  Atheros Kconfig needs to be dependent on WLAN_80211
  mac80211: fix docbook
  mac80211_hwsim: avoid NULL access
  ssb: Add support for 4318E
  b43: Add support for 4318E
  zd1211rw: adding SONY IFU-WLM2 (054c:0257) as a zd1211b device
  zd1211rw: 07b8:6001 is a ZD1211B
  r6040: bump driver version to 0.24 and date to 08 July 2009
  r6040: restore MIER register correctly when IRQ line is shared
  ipv4: Fix fib_trie rebalancing, part 4 (root thresholds)
  davinci_emac: fix kernel oops when changing MAC address while interface is down
  igb: set lan id prior to configuring phy
  mac80211: minstrel: avoid accessing negative indices in rix_to_ndx()
  ...

Looks like the change in ad361c98
wasn't compile tested.
Signed-off-by: NDave Jones <davej@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization.  For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port.  This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.

Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.

Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding smp_mb__after_lock define to be used as a smp_mb call after
a lock.

Making it nop for x86, since {read|write|spin}_lock() on x86 are
full memory barriers.
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding memory barrier after the poll_wait function, paired with
receive callbacks. Adding fuctions sock_poll_wait and sk_has_sleeper
to wrap the memory barrier.

Without the memory barrier, following race can happen.
The race fires, when following code paths meet, and the tp->rcv_nxt
and __add_wait_queue updates stay in CPU caches.

CPU1                         CPU2

sys_select                   receive packet
  ...                        ...
  __add_wait_queue           update tp->rcv_nxt
  ...                        ...
  tp->rcv_nxt check          sock_def_readable
  ...                        {
  schedule                      ...
                                if (sk->sk_sleep && waitqueue_active(sk->sk_sleep))
                                        wake_up_interruptible(sk->sk_sleep)
                                ...
                             }

If there was no cache the code would work ok, since the wait_queue and
rcv_nxt are opposit to each other.

Meaning that once tp->rcv_nxt is updated by CPU2, the CPU1 either already
passed the tp->rcv_nxt check and sleeps, or will get the new value for
tp->rcv_nxt and will return with new data mask.
In both cases the process (CPU1) is being added to the wait queue, so the
waitqueue_active (CPU2) call cannot miss and will wake up CPU1.

The bad case is when the __add_wait_queue changes done by CPU1 stay in its
cache, and so does the tp->rcv_nxt update on CPU2 side.  The CPU1 will then
endup calling schedule and sleep forever if there are no more data on the
socket.

Calls to poll_wait in following modules were ommited:
	net/bluetooth/af_bluetooth.c
	net/irda/af_irda.c
	net/irda/irnet/irnet_ppp.c
	net/mac80211/rc80211_pid_debugfs.c
	net/phonet/socket.c
	net/rds/af_rds.c
	net/rfkill/core.c
	net/sunrpc/cache.c
	net/sunrpc/rpc_pipe.c
	net/tipc/socket.c
Signed-off-by: NJiri Olsa <jolsa@redhat.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix compile failure in cpufreq.c

Using early netconsole and gianfar driver this error pops up:

  netconsole: timeout waiting for carrier

It appears that net/core/netpoll.c:netpoll_setup() is using
cond_resched() in a loop waiting for a carrier.

The thing is that cond_resched() is a no-op when system_state !=
SYSTEM_RUNNING, and so drivers/net/phy/phy.c's state_queue is never
scheduled, therefore link detection doesn't work.

I belive that the main problem is in cond_resched()[1], but despite
how the cond_resched() story ends, it might be a good idea to call
msleep(1) instead of cond_resched(), as suggested by Andrew Morton.

[1] http://lkml.org/lkml/2009/7/7/463Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ad361c98 ("Remove multiple KERN_ prefixes from printk formats")
broke the build for fealnx because it added some "printk(PR_CONT ..."
calls, when PR_CONT doesn't exist; it should be "printk(KERN_CONT ..."
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

managed_policy is out of scope for the non-smp case.
Declare it locally where used (twice)
Signed-off-by: NDave Jones <davej@redhat.com>

Remove not needed locking of the fb_info->mm_lock mutex before a
frambuffer is registered.

This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf0 " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove call to the fsl_diu_set_par before the register_framebuffer().

This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf0 " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: N"Kai Jiang" <b18973@freescale.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

fix the following 'make includecheck' warning:

  include/linux/rfkill.h: linux/types.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:

WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active

This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.

This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These two functions no longer exist in mac80211,
so trying to insert them generates warnings in
the document.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: NClyde McPherson <ccmcphe@verizon.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: NClyde McPherson <ccmcphe@verizon.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:

Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: NYevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"

It appears that this simple patch makes the device work perfectly.

This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: NPascal Terjan <pterjan@mandriva.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: NSteve Holland <sdh4@iastate.edu>
Signed-off-by: NJoe Chou <joe.chou@rdc.com.tw>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pawel Staszewski wrote:
<blockquote>
Some time ago i report this:
http://bugzilla.kernel.org/show_bug.cgi?id=6648

and now with 2.6.29 / 2.6.29.1 / 2.6.29.3 and 2.6.30 it back
dmesg output:
oprofile: using NMI interrupt.
Fix inflate_threshold_root. Now=15 size=11 bits
...
Fix inflate_threshold_root. Now=15 size=11 bits

cat /proc/net/fib_triestat
Basic info: size of leaf: 40 bytes, size of tnode: 56 bytes.
Main:
        Aver depth:     2.28
        Max depth:      6
        Leaves:         276539
        Prefixes:       289922
        Internal nodes: 66762
          1: 35046  2: 13824  3: 9508  4: 4897  5: 2331  6: 1149  7: 5
9: 1  18: 1
        Pointers: 691228
Null ptrs: 347928
Total size: 35709  kB
</blockquote>

It seems, the current threshold for root resizing is too aggressive,
and it causes misleading warnings during big updates, but it might be
also responsible for memory problems, especially with non-preempt
configs, when RCU freeing is delayed long after call_rcu.

It should be also mentioned that because of non-atomic changes during
resizing/rebalancing the current lookup algorithm can miss valid leaves
so it's additional argument to shorten these activities even at a cost
of a minimally longer searching.

This patch restores values before the patch "[IPV4]: fib_trie root
node settings", commit: 965ffea4 from
v2.6.22.

Pawel's report:
<blockquote>
I dont see any big change of (cpu load or faster/slower
routing/propagating routes from bgpd or something else) - in avg there
is from 2% to 3% more of CPU load i dont know why but it is - i change
from "preempt" to "no preempt" 3 times and check this my "mpstat -P ALL
1 30"
always avg cpu load was from 2 to 3% more compared to "no preempt"
[...]
cat /proc/net/fib_triestat
Basic info: size of leaf: 20 bytes, size of tnode: 36 bytes.
Main:
        Aver depth:     2.44
        Max depth:      6
        Leaves:         277814
        Prefixes:       291306
        Internal nodes: 66420
          1: 32737  2: 14850  3: 10332  4: 4871  5: 2313  6: 942  7: 371  8: 3  17: 1
        Pointers: 599098
Null ptrs: 254865
Total size: 18067  kB
</blockquote>

According to this and other similar reports average depth is slightly
increased (~0.2), and root nodes are shorter (log 17 vs. 18), but
there is no visible performance decrease. So, until memory handling is
improved or added parameters for changing this individually, this
patch resets to safer defaults.
Reported-by: NPawel Staszewski <pstaszewski@itcare.pl>
Reported-by: NJorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Tested-by: NPawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check that network interface is running before changing its MAC address.
Otherwise, rxch is accessed when it's NULL - causing a kernel oops.
Moreover, check that the new MAC address is valid.
Signed-off-by: NPablo Bitton <pablo.bitton@gmail.com>
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Tested-by: NChaithrika U S <chaithrika@ti.com>
[tested on DM6467 EVM]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igb driver was defaulting to using the lock for pci-e function 0 for
all of the phys due to the fact that the lan id was not being set prior to
initialization.  This change makes it so that the function id is set prior
to checking for the phy id.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alex found that specjbb2005 still can not run with hugepages on an
x86-64 machine.  This only happens when numa is not compiled in.

The root cause: node_set_state will not set it back for us in that case,
so don't clear that when numa is not select in config

[ v2: use node_clear_state instead ]
Reported-and-Tested-by: NAlex Shi <alex.shi@intel.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5fd29d6c ("printk: clean up
handling of log-levels and newlines") changed printk semantics.  printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.

<level> is now included in the output on each additional use.

Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move tty entries to tty not trivial. Noted by David Brownell.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes the ppp problems and various other issues with call locking
caused by one side of a pty called in one locking context trying to match
another with differing rules on the other side. We also get a big slack
space to work with that means we can bury the flow control deadlock case
for any conceivable real world situation.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Powernow-k8: support family 0xf with 2 low p-states
  [CPUFREQ] fix (utter) cpufreq_add_dev mess
  [CPUFREQ] Cleanup locking in conservative governor
  [CPUFREQ] Cleanup locking in ondemand governor
  [CPUFREQ] Mark policy_rwsem as going static in cpufreq.c wont be exported
  [CPUFREQ] Eliminate the recent lockdep warnings in cpufreq

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-quota-2.6:
  quota: Fix possible deadlock during parallel quotaon and quotaoff

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Clear -EAGAIN in dpm_prepare
  x86: Fix resume from suspend when CONFIG_CC_STACKPROTECTOR

After some API change, intel_iommu_unmap_range() introduced a assumption that
parameter size != 0, otherwise the dma_pte_clean_range() would have a
overflowed argument. But the user like KVM don't have this assumption before,
then some BUG() triggered.

Fix it by ignoring size = 0.
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The f_dev in _request_firmware() is allocated via the fw_setup_device()
and fw_register_device() calls and its class set to firmware_class (the
class release function is fw_dev_release).

Commit 6acf70f0 replaced the kfree(dev) in fw_dev_release() with a
put_device() call but my understanding is that the release function is
called via put_device -> kobject_put -> kref_put -> koject_release etc.
and it should call kfree since it's the last to see this device
structure alive.

Because of that, the _request_firmware() function on its -ENOENT error
path only calls device_unregister(f_dev) which would eventually call
fw_dev_release() but there is no kfree (the subsequent put_device call
would just make the kref negative).
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 1c8542c7 replaced kmalloc() with memdup_user() in the write()
function but also dropped the kfree(temp). The memdup_user() function
allocates memory which is never freed.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Cc: Parag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: gpio_mouse - use standard driver registration method
  Input: mark serio and i8042 as suspended when hibernating too
  Input: add support for generic GPIO-based matrix keypad
  Input: arrange keyboards alphabetically
  Input: gpio-keys - avoid possibility of sleeping in timer function
  Input: gpio-keys - revert 'change timer to workqueue'
  Input: dm355evm_keys - fix kconfig symbol names
  Input: wacom - add DTF720a support and fix rotation on Intuos3
  Input: i8042 - more reset quirks for MSI Wind-clone netbooks

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Don't use alloc_bootmem() in init_IRQ() path
  powerpc: Fix spin_event_timeout() to be robust over context switches
  powerpc: Use pr_devel() in do_dcache_icache_coherency()
  powerpc/cell: Use pr_devel() in axon_msi.c
  powerpc: Use pr_devel() in arch/powerpc/mm/gup.c
  powerpc: Cleanup & use pr_devel() in arch/powerpc/mm/slb.c
  powerpc/perf_counter: Remove duplicated #include
  powerpc: Use pr_devel() in arch/powerpc/mm/mmu_context_nohash.c
  powerpc/pseries: Use pr_devel() in xics.c
  powerpc: Remove unnecessary semicolons
  powerpc/pseries: Use pr_devel() in pseries LPAR HPTE routines
  powerpc/44x: Fix build error with -Werror for Warp platform
  powerpc/4xx: Have Warp take advantage of GPIO LEDs default-state = keep
  powerpc/44x: Update Warp defconfig

Fix various silly problems wrt mnt_namespace.h:

 - exit_mnt_ns() isn't used, remove it
 - done that, sched.h and nsproxy.h inclusions aren't needed
 - mount.h inclusion was need for vfsmount_lock, but no longer
 - remove mnt_namespace.h inclusion from files which don't use anything
   from mnt_namespace.h
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>