- 22 9月, 2008 1 次提交
-
-
由 Andrew Victor 提交于
In the various AT91 board files, replace hard-coded size values (eg, 0x800000) with the SZ_ size definitions (eg, SZ_8M) from sizes.h Also replace MTD partition offsets with MTDPART_OFS_NXTBLK. Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 07 8月, 2008 2 次提交
-
-
由 Russell King 提交于
This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h. Then, since asm/hardware.h only exists to include asm/arch/hardware.h, update everything to directly include asm/arch/hardware.h and remove asm/hardware.h. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 01 8月, 2008 1 次提交
-
-
由 Pieter du Preez 提交于
Structs called at91_nand_data where renamed to atmel_nand_data and configs called *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL*. This was unfortunately not done consistently, causing NAND chips not being initialised on several ARM boards. I am aware that the author of the original change did not rename MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example. All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order to keep naming consistency. This patch was only tested on a MACH_SAM9_L9260, as this is the only ARM board I have to my disposal. Before this patch: $ git-ls-files |xargs grep atmel_nand |wc -l 105 $ git-ls-files |xargs grep at91_nand |wc -l 4 $ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l 8 $ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l 47 After this patch: $ git-ls-files |xargs grep atmel_nand |wc -l 109 $ git-ls-files |xargs grep at91_nand |wc -l 0 $ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l 55 $ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l 0 Signed-off-by: NPieter du Preez <pdupreez@gmail.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
- 29 7月, 2008 1 次提交
-
-
由 Haavard Skinnemoen 提交于
struct at91_nand has been renamed atmel_nand. Fix the four boards that were added since the patch was created. Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com> Acked-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 02 6月, 2008 1 次提交
-
-
由 Andrew Victor 提交于
Add support for three AT91-based boards available from Calao Systems: USB_A9260, USB_A9263 and QIL_A9260. Signed-off-by: NGrégory Hermant <gregory.hermant@calao-systems.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 17 4月, 2008 1 次提交
-
-
由 Andrew Victor 提交于
Support for the Olimex SAM9-L9260 board. <http://www.olimex.com/dev/sam9-L9260.html> Original patch from Ivan Vasilev. Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 04 4月, 2008 4 次提交
-
-
由 Andrew Victor 提交于
Add support for the GPIO-driven LEDs (using NEW_LEDS) on the Atmel SAM9260-EK and SAM9261-EK boards. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Add support for AT73C213 audio DAC on the Atmel SAM9260-EK and SAM9261-EK boards. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Convert the Atmel SAM9260-EK, SAM9261-EK, SAM9263-EK and SAM9RL-EK boards to use the new-style UART initialization. Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
The AT91CAP9 processor includes the same Static Memory Controller (SMC) peripheral as the SAM9 processors, but replaces the SDRAM Controller with a DDR/SDR Controller (DDRSDRC). This patch splits the existing include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and at91sam9_smc.h. It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller. Signed-off-by: NAndrew Victor <linux@maxim.org.za> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 27 11月, 2007 1 次提交
-
-
由 Andrew Victor 提交于
The AT91 I2C driver is currently marked as "broken" due to hardware issues. This patch enables AT91-based platforms to also use the bitbanged GPIO for I2C. This updates platform setup logic (setting up an i2c-gpio device using the same pins as the i2c-at91 device, unless only the BROKEN driver is enabled). Also make use of the new-style initialization of I2C devices using i2c_register_board_info(). Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 04 5月, 2007 1 次提交
-
-
由 Andrew Victor 提交于
Various small changes for the Atmel AT91SAM9260-EK and AT91SAM9263-EK boards. SAM9260-EK: - Register I2C device. SAM9263-EK: - Add platform_data and register MACB device. (Patch by Nicolas Ferre) - Add platform_data and register AC97 device. (Patch by Nicolas Ferre) - Register I2C device. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 28 4月, 2007 1 次提交
-
-
由 Sam Ravnborg 提交于
Andrew Morton found a section mismatch warning in x86_64 triggered by a wrongly placed __initdata marker. git grep "struct __initdata" revealed that board-sam9260.c had the same problem. This patch fixes this by placing the __initdata marker correct. It was checked with objdump that the variable was moved to .init.data by this change. Fixed an unrelated section mismatch warning while touching the file. Both changes are only compile tested but obvious correct. [Used at91sam9260ek_defconfig to get compile coverage] Signed-off-by: NSam Ravnborg <sam@ravnborg.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 08 2月, 2007 3 次提交
-
-
由 Andrew Victor 提交于
The Atmel AT91SAM9263 processor includes many more integrated peripherals than Atmel's previous ARM9-based AT91 processors, so this has necessitated a few changes to the core AT91 support. These changes are: * The system peripheral I/O region we remap has increased from 0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF. * The increased I/O region forces changes to entry-macro.S and debug-macro.S due to ARM's limited immediate offset addressing modes. * Maximum number of GPIO banks increases to 5. * 2 MMC controllers so the board-setup code needs to specify which controller it wishes to use when calling at91_add_device_mmc(). Original patch from Nicolas Ferre. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Now that Linux includes support for the Atmel AT91SAM9260 and AT91SAM9261 processors in addition to the original Atmel AT91RM9200 (with support for more AT91 processors pending), the "mach-at91rm9200" and "arch-at91rm9200" directories should be renamed to indicate their more generic nature. The following git commands should be run BEFORE applying this patch: git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91 git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91 Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Fix build failure of AT91SAM9260. The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a "struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263) ethernet driver (macb.c) [developed on the AVR32 architecture] expects a "struct eth_platform_data". Since the platform data of the two drivers is very similar, we continue to use the "struct at91_eth_data" for all AT91 processors but add a #define eth_platform_data at91_eth_data in board.h to keep the MACB driver happy. Original patch by Jan Altenberg. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 08 12月, 2006 1 次提交
-
-
由 Andrew Victor 提交于
Add PHY IRQ pin definition for AT91SAM9260-EK board. Signed-off-by: NWojtek Kaniewski <wojtekka@toxygen.net> Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 02 12月, 2006 1 次提交
-
-
由 Andrew Victor 提交于
This patch adds support for the Atmel AT91SAM9260-EK board. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 01 12月, 2006 1 次提交
-
-
由 Andrew Victor 提交于
This patch converts the old CONFIG_MTD_PHYSMAP_ options to the new physmap API by creating a physmap platform device for the NOR flash found on the Atmel AT91RM9200-DK and AT91RM9200-EK boards. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 28 9月, 2006 2 次提交
-
-
由 Andrew Victor 提交于
This patch makes the AT91 gpio.c support processor-generic (AT91RM9200 and AT91SAM9xxx). The GPIO controllers supported by a particular AT91 processor are defined in the processor-specific file and are registered with gpio.c at startup. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
This patch makes the AT91 clock.c support processor-generic (AT91RM9200 and AT91SAM9xxx). The clocks supported by a particular AT91 processor are defined in the processor-specific file and are registered with clock.c at startup. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 21 6月, 2006 1 次提交
-
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 20 6月, 2006 1 次提交
-
-
由 Andrew Victor 提交于
Patch from Andrew Victor This patch updates the support for the Atmel DK and EK boards. The changes include: 1. Use the new at91_uart_config structure and device registration functions for the UARTs. 2. Registration of I2C and SPI platform devices. 3. The USB Device pullup line is connected to reset, so multidrive needs to be enabled on the line. [Patch from David Brownell]. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 03 4月, 2006 2 次提交
-
-
由 Andrew Victor 提交于
Patch from Andrew Victor On the Atmel AT91RM9200-DK and -EK boards, a pin is used to control whether the card socket is used for a DataFlash Card or an MMC/SD card. We now default to MMC/SD in the configuration files. (This version of the patch can be applied before Patch 3392/1) Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Andrew Victor 提交于
Patch from Andrew Victor This patch adds support for the LED(s) on the AT91RM9200-based boards. (This version of the patch can be applied before Patch 3392/1) Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 14 1月, 2006 1 次提交
-
-
由 Nicolas Pitre 提交于
Patch from Nicolas Pitre This field is redundent since it must be equal to PHYS_OFFSET anyway. Now that no code uses it anymore, mark it deprecated and remove all initializations from the tree. Signed-off-by: NNicolas Pitre <nico@cam.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 11 1月, 2006 1 次提交
-
-
由 Andrew Victor 提交于
Patch from Andrew Victor This patch adds support to the 2.6 kernel series for the Atmel AT91RM9200 processor. This patch is the support for Atmel's DK and EK boards. Signed-off-by: NAndrew Victor <andrew@sanpeople.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-