efi_initialize_iomem_resources() is declared in both include/linux/efi.h
and arch/ia64/kernel/setup.c. This patch removes the latter.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Berhhard Walle noted that on his HP rx8640 he ended up with saved_max_pfn
smaller than the highest address of system ram in /proc/iomem and proposed
a patch to base the address on the unrounded and unfiltered EFI memory
map address.  Simon Horman and Magnus Damm suggested that the whole test
be moved earlier in the function.  This is the combination of both of
these patches.
Signed-off-by: NTony Luck <tony.luck@intel.com>

This patch fixes boot failure because irq_desc->mask() is NULL.

- Added mask/unmask functions to ia64's irq desc function table.
- rename hw_interrupt_type to irq_chip. hw_interrupt_type is old name.
- Tony: Added same change to arch/ia64/sn/kernel/irq.c as pointed out
  by Eric Biederman ... mask/unmask functions there can be no-op.
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Remove un-used/un-referenced local_bh_count.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use irq_handler_t for passing clock handler routine around.
And use new rtc_time in place of hwclock_time.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove regs arg from bad interrupt handler.
Use irq_handler_t type for handler arg of local request_irq().
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use irq_handler_t type for passing around timer interrupt routine
in 368360 setup code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use irq_handler_t type for passing around timer interrupt routine.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Apply commit 0550d9d1 to c-tx39.c too.
And fix a warning in local_tx39_flush_data_cache_page().
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Should now be understandable why the thing works ...
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The address where the ELF core header is stored is passed to the secondary
kernel as a kernel command line option.  The memory area for this header is
also marked as a separate EFI memory descriptor on ia64.

The separate EFI memory descriptor is at the moment of the type
EFI_UNUSABLE_MEMORY.  With such a type the secondary kernel skips over the
entire memory granule (config option, 16M or 64M) when detecting memory.
If we are lucky we will just lose some memory, but if we happen to have
data in the same granule (such as an initramfs image), then this data will
never get mapped and the kernel bombs out when trying to access it.

So this is an attempt to fix this by changing the EFI memory descriptor
type into EFI_LOADER_DATA.  This type is the same type used for the kernel
data and for initramfs.  In the secondary kernel we then handle the ELF
core header data the same way as we handle the initramfs image.

This patch contains the kernel changes to make this happen.  Pretty
straightforward, we reserve the area in reserve_memory().  The address for
the area comes from the kernel command line and the size comes from the
specialized EFI parsing function vmcore_find_descriptor_size().

The kexec-tools-testing code for this can be found here:
http://lists.osdl.org/pipermail/fastboot/2007-February/005983.htmlSigned-off-by: NMagnus Damm <magnus@valinux.co.jp>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Perfmon associates vmalloc()ed memory with a file descriptor, and installs
a vma mapping that memory.  Unfortunately, the vm_file field is not filled
in, so processes with mappings to that memory do not prevent the file from
being closed and the memory freed.  This results in use-after-free bugs and
multiple freeing of pages, etc.

I saw this bug on an Altix on SLES9.  Haven't reproduced upstream but it
looks like the same issue is there.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Add VERIFY_WRITE check in the beginning like compat_sys_getdents() (EINVAL vs
EFAULT).
Signed-off-by: NAlexandr Andreev <aandreev@openvz.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Always build ia64 xor.o because multiple config options now depend on it.

Necessary to build .20-mm* on ia64 when, e.g., CONFIG_ASYNC_TX_DMA is
defined.  Don't know if '_ASYNC_TX_DMA makes sense on ia64.  If not, maybe
Kconfig should preclude it.

Could have defined a Kconfig option that defaults to true if MD_RAID456 ||
ASYNC_TX_DMA to control building of xor.o, but xor.o is only 848 bytes and
this IS ia64...
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Make saved_max_pfn point to max_pfn of entire system.

Without this patch is so that vmcore is zero length on ia64.  This is
because saved_max_pfn was wrongly being set to the max_pfn of the crash
kernel's address space, rather than the max_pfg on the physical memory of
the machine - the whole purpose of vmcore is to access physical memory that
is not part of the crash kernel's addresss space.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NZou Nan hai <nanhai.zou@intel.com>
Sort-Of-Acked-By: NJay Lan <jlan@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Comment the fact that sig_info is initialized early in boot, and thus doesn't
need any locking.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a debugging message in the case that mapping a stub fails.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a few formatting bugs in the signal code.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the no longer used custom_sched_clock.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NZachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal.  Fixup the remaining users.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device.  This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port.  Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.

This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replaced check_user_space() + __check_access_register with the new
check_space(). The old functions made wrong assumptions about kernel
and user space when the kernel and user address spaces are switched
(kernel in home space, user in primary/secondary space).
Secondly the user process can switch to the accress register mode if
it is running in primary or secondary mode. In addition it can load
an arbitrary value to the access registers. If any other value than
0 for primary space or 1 for secondary space is loaded and memory
is accessed using the base register related to the access register,
the program should be terminated with a SIGSEGV. To achieve that the
DUALD pointer in the DUCT and the PSALD pointer in the PASTE need
to point to an array of 8 invalid access-list entries to get a
ALEN-translation exception if an invalid alet is used.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

nss and kexec don't work together since kexec wants to write to the
read-only text section of the shared kernel image.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Reipl doesn't work on older machines were s390_reset_machine() gets
called. The reason is that the text section is read-only but the
variable dump_prefix_page is there. Since s390_reset_machine() writes
to it we get a protection exception.
Therefore move dump_prefix_page to the bss section.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Avoid sprinkling a _lot_ of preempt_disable/preempt_enable pairs.
This would be necessary for e.g. the iucv driver. Also this way we
are more consistent with other architectures which disable
preemption at least for smp_call_function.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The illegal operation handler calls the die notifier with DIE_BPT to
let kprobes pick up its breakpoint. If kprobes does not find its
breakpoint it returns NOTIFY_STOP instead of NOTIFY_DONE.
Since we use stop_machine_run on s390 to arm/disarm the kprobes
breakpoints the race that kprobe_handler tries to solve by checking
for the kprobes breakpoints does not exist. Removing the check makes
BUG_ON working again.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

CONFIG_PARAVIRT broke old glibc bootup: it silently turned off the
selectability of CONFIG_COMPAT_VDSO and thus rendered distro kernels
unbootable on old-style VDSO glibc setups.

the proper solution is to keep COMPAT_VDSO available - if a hypervisor
needs any modification of that concept then we'll judge those changes in
full context, once those changes are submitted.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

do not use default=y for CONFIG_VMI (we do not do that for any driver or
special-hardware feature): the overwhelming majority of Linux users does
not need it, and interested users and distributions can enable it
as-needed.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clarify the description of the CONFIG_VMI option: describe the reality
that VMI is a VMWare-only interface for now. Once that changes and
another hypervisor adopts the VMI ABI we can change the text.

As can be seen from the Xen paravirtualization patches submitted to lkml
the Xen project has chosen its own, non-VMI interface between Xen and
the para-Linux - so remove Xen from the description.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Temove the mistaken turning on of NO_IDLE_HZ on x86+PARAVIRT kernels.

It's an obsolete, limited form of dynticks.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  CC      arch/i386/kernel/vmi.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c: In function 'vmi_map_pt_hook':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE0' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE1' undeclared (first use in this function)
make[2]: *** [arch/i386/kernel/vmi.o] Error 1
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426

The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.

It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.

Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).

This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removes unused 'flags' variable from setup_IO_APIC_irq().
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  Testing NMI watchdog ... CPU#0: NMI appears to be stuck (54->54)!
  CPU#1: NMI appears to be stuck (0->0)!

Keep the PIT/HPET alive when nmi_watchdog = 1 is given on the command
line.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Critical fixes for SMP.

Fix a couple functions which needed to be __devinit and fix a bogus parameter
to AP startup that just so happened to work because the low virtual mapping of
memory was still established.
Signed-off-by: NZachary Amsden <zach@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>