Scot Doyle demonstrated ip_options_compile() could be called with an skb
without an attached route, using a setup involving a bridge, netfilter,
and forged IP packets.

Let's make ip_options_compile() and ip_options_rcv_srr() a bit more
robust, instead of changing bridge/netfilter code.

With help from Hiroaki SHIMODA.
Reported-by: NScot Doyle <lkml@scotdoyle.com>
Tested-by: NScot Doyle <lkml@scotdoyle.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: NHiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

USB tethering does not work anymore since 2.6.39-rc2, but it's okay in
-rc1. The root cause is the new added mask code 'FLAG_POINTTOPOINT'
overlaps 'FLAG_MULTI_PACKET'  in  include/linux/usb/usbnet.h, this
causes logic issue in  rx_process(). This patch cleans up the overlap.
Reported-and-Tested-by: NGottfried Haider <gottfried.haider@gmail.com>
Signed-off-by: NHuajun Li <huajun.li.lee@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like

[   58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[   58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).

if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: NRobin Dong <hao.bigrat@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit c191a836.

It causes known regressions for programs that expect to be able to use
SO_REUSEADDR to shutdown a socket, then successfully rebind another
socket to the same ID.

Programs such as haproxy and amavisd expect this to work.

This should fix kernel bugzilla 32832.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.

Fixing it by pulling extra frags.

Cc: stable@kernel.org
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 74888760
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we can not update retran path to unconfirmed transports,
when we remove a peer, the retran path may not be update if the
other transports are all unconfirmed, and we will still using
the removed transport as the retran path. This may cause panic
if retrasnmit happen.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit fbdf501c
  sctp: Do no select unconfirmed transports for retransmissions

Introduced the initial falt.

commit d598b166
  sctp: Make sure we always return valid retransmit path

Solved the problem, but forgot to change the DEBUG statement.
Thus it was still possible to dereference a NULL pointer.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_TSO_ECN has no effect when TSO is disabled; this just means
that feature state will be accurately reported to user-space.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The feature flags NETIF_F_TSO and NETIF_F_TSO6 independently enable
TSO for IPv4 and IPv6 respectively.  However, the test in
netdev_fix_features() and its predecessor functions was never updated
to check for NETIF_F_TSO6, possibly because it was originally proposed
that TSO for IPv6 would be dependent on both feature flags.

Now that these feature flags can be changed independently from
user-space and we depend on netdev_fix_features() to fix invalid
feature combinations, it's important to disable them both if
scatter-gather is disabled.  Also disable NETIF_F_TSO_ECN so
user-space sees all TSO features as disabled.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling write-combining may also enable read reordering.  The BIU is
only guaranteed to read from a 128-bit CSR or 64-bit SRAM word when
the host reads from its lowest address; otherwise the BIU may use the
latched value.  Therefore we need to reinstate the read memory
barriers after the first read operation for each CSR or SRAM word.

Signed-off-by; Ben Hutchings <bhutchings@solarflare.com>

It adds -Wall (which the kernel carefully controls already) and of all
things -DDEBUG (which should be set by other means if desired, please
we have dynamic-debug these days).

Kill this noise.
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5b40964e ("irda: Remove BKL instances
from af_irda.c") introduced a path where we have a locking unbalance.
If we pass invalid flags, we unlock a socket we never locked,
resulting in this...

=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
trinity/20101 is trying to release lock (sk_lock-AF_IRDA) at:
[<ffffffffa057f001>] irda_sendmsg+0x207/0x21d [irda]
but there are no more locks to release!

other info that might help us debug this:
no locks held by trinity/20101.

stack backtrace:
Pid: 20101, comm: trinity Not tainted 2.6.39-rc3+ #3
Call Trace:
 [<ffffffffa057f001>] ? irda_sendmsg+0x207/0x21d [irda]
 [<ffffffff81085041>] print_unlock_inbalance_bug+0xc7/0xd2
 [<ffffffffa057f001>] ? irda_sendmsg+0x207/0x21d [irda]
 [<ffffffff81086aca>] lock_release+0xcf/0x18e
 [<ffffffff813ed190>] release_sock+0x2d/0x155
 [<ffffffffa057f001>] irda_sendmsg+0x207/0x21d [irda]
 [<ffffffff813e9f8c>] __sock_sendmsg+0x69/0x75
 [<ffffffff813ea105>] sock_sendmsg+0xa1/0xb6
 [<ffffffff81100ca3>] ? might_fault+0x5c/0xac
 [<ffffffff81086b7c>] ? lock_release+0x181/0x18e
 [<ffffffff81100cec>] ? might_fault+0xa5/0xac
 [<ffffffff81100ca3>] ? might_fault+0x5c/0xac
 [<ffffffff81133b94>] ? fcheck_files+0xb9/0xf0
 [<ffffffff813f387a>] ? copy_from_user+0x2f/0x31
 [<ffffffff813f3b70>] ? verify_iovec+0x52/0xa6
 [<ffffffff813eb4e3>] sys_sendmsg+0x23a/0x2b8
 [<ffffffff81086b7c>] ? lock_release+0x181/0x18e
 [<ffffffff810773c6>] ? up_read+0x28/0x2c
 [<ffffffff814bec3d>] ? do_page_fault+0x360/0x3b4
 [<ffffffff81087043>] ? trace_hardirqs_on_caller+0x10b/0x12f
 [<ffffffff810458aa>] ? finish_task_switch+0xb2/0xe3
 [<ffffffff8104583e>] ? finish_task_switch+0x46/0xe3
 [<ffffffff8108364a>] ? trace_hardirqs_off_caller+0x33/0x90
 [<ffffffff814bbaf9>] ? retint_swapgs+0x13/0x1b
 [<ffffffff81087043>] ? trace_hardirqs_on_caller+0x10b/0x12f
 [<ffffffff810a9dd3>] ? audit_syscall_entry+0x11c/0x148
 [<ffffffff8125609e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
 [<ffffffff814c22c2>] system_call_fastpath+0x16/0x1b
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a skb is delivered to a registered callback, cn_call_callback()
incorrectly returns -ENODEV after freeing the skb, causing cn_rx_skb()
to free the skb a second time.
Reported-by: NEric B Munson <emunson@mgebm.net>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Tested-by: NEric B Munson <emunson@mgebm.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

controlling igmp_max_membership is useful even when IP_MULTICAST
is off.
Quagga(an OSPF deamon) uses multicast addresses for all interfaces
using a single socket and hits igmp_max_membership limit when
there are 20 interfaces or more.
Always export sysctl igmp_max_memberships in proc, just like
igmp_max_msf
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 64bit arches, we use 752 bytes of stack when cleanup_once() is called
from inet_getpeer().

Lets share the avl stack to save ~376 bytes.

Before patch :

# objdump -d net/ipv4/inetpeer.o | scripts/checkstack.pl

0x000006c3 unlink_from_pool [inetpeer.o]:		376
0x00000721 unlink_from_pool [inetpeer.o]:		376
0x00000cb1 inet_getpeer [inetpeer.o]:			376
0x00000e6d inet_getpeer [inetpeer.o]:			376
0x0004 inet_initpeers [inetpeer.o]:			112
# size net/ipv4/inetpeer.o
   text	   data	    bss	    dec	    hex	filename
   5320	    432	     21	   5773	   168d	net/ipv4/inetpeer.o

After patch :

objdump -d net/ipv4/inetpeer.o | scripts/checkstack.pl
0x00000c11 inet_getpeer [inetpeer.o]:			376
0x00000dcd inet_getpeer [inetpeer.o]:			376
0x00000ab9 peer_check_expire [inetpeer.o]:		328
0x00000b7f peer_check_expire [inetpeer.o]:		328
0x0004 inet_initpeers [inetpeer.o]:			112
# size net/ipv4/inetpeer.o
   text	   data	    bss	    dec	    hex	filename
   5163	    432	     21	   5616	   15f0	net/ipv4/inetpeer.o
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Scot Doyle <lkml@scotdoyle.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Reviewed-by: NHiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the correct module name and device interface so that
ethtool can display the proper values.

The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: NRichard Farina <sidhayn@gmail.com>
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: NRichard Farina <sidhayn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.

This typically shows up in the kernel log with messages like these:

ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]

When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.

This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 462fb2af (bridge : Sanitize skb before it enters the IP
stack), missed one IPCB init before calling ip_options_compile()

Thanks to Scot Doyle for his tests and bug reports.
Reported-by: NScot Doyle <lkml@scotdoyle.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Acked-by: NBandan Das <bandan.das@stratus.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Cc: Jan Lübbe <jluebbe@debian.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During self-tests we use efx_process_channel_now() to handle
completion and other events synchronously.  This disables interrupts
and NAPI processing for the channel in question, but it may still be
interrupted by another channel.  A single socket may receive packets
from multiple net devices or even multiple channels of the same net
device, so this can result in deadlock on a socket lock.

Receiving packets in process context will also result in incorrect
classification by the network cgroup classifier.

Therefore, we must only use efx_process_channel_now() in the offline
loopback tests (which never deliver packets up the stack) and not for
the online interrupt and event tests.

For the interrupt test, there is no reason to process events.  We
only care that an interrupt is raised.

For the event test, we want to know whether events have been received,
and there may be many events ahead of the one we inject.  Therefore
remove efx_channel::magic_count and instead test whether
efx_channel::eventq_read_ptr advances.  This is currently an event
queue index and might wrap around to exactly the same value, resulting
in a false negative.  Therefore move the masking to efx_event() and
efx_nic_eventq_read_ack() so that it cannot wrap within the time of
the test.

The event test also tries to diagnose failures by checking whether an
event was delivered without causing an interrupt.  Add and use a
helper function that only does this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

If the TX queues are running during loopback self tests, host
traffic gets looped back which causes the test to fail.  Avoid
restarting the TX queues after the port reset so that any packets
sent by the host get held back until after the tests have completed.

[bwh: Also wake all TX queues at the end of self-tests.]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Fixes bugzilla #32872

The LLC stack pretends to support non-linear skbs but there is a
direct use of skb_tail_pointer() in llc_fixup_skb().

Use pskb_may_pull() to see if data_size bytes remain and can be
accessed linearly in the packet, instead of direct pointer checks.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

    In the CAIF Payload message the Packet Type indication must be set to
    UNCLASSIFIED in order to allow packet prioritization in the modem's
    network stack. Otherwise TCP-Ack is not prioritized in the modems
    transmit queue.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.

Fixing it by pulling extra frags.

Cc: stable@kernel.org
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace relpy with reply.
replace premanent with permanent.
Signed-off-by: NWeiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace tranmitted with transmitted.
replace tranmitting with transmitting.
Signed-off-by: NWeiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now, alb_bond_info uses rx_ntt,rlb_update_delay_counter and
rlb_update_retry_counter to decide when to call rlb_update_rx_clients().
Signed-off-by: NWeiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now bonding-alb uses delayed_work instead of timer_list.
Signed-off-by: NWeiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.
Signed-off-by: NWeiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some old MAC chips without COE sometime the
Transmit Underflow error is issued.

The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.

The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: NNachiketa Prachanda <nprachanda@ncomputing.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Hacked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a compilation error when build the
dwmac_lib with the DEBUG option enabled.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>