Remove ieee80211_set_aid_for_sta and associated code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This constant is unused.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes mac80211 show transmitted frames on monitor interfaces,
including radiotap headers that indicate some transmission parameters.
The shown parameters will need to be expanded, but this should work as
a basis to work from.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAndy Green <andy@warmcat.com>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Generic code to walk through the fields in a radiotap header, accounting
for nasties like extended "field present" bitfields and alignment rules
Signed-off-by: NAndy Green <andy@warmcat.com>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add monitor mode radiotap injection docs.
Signed-off-by: NAndy Green <andy@warmcat.com>
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a missing NVRAM strapping for 5755 devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds automatic MDI crossover support when autonegotiation is
turned off.  Automatic MDI crossover allows link to be established
without the use of a crossover cable.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For most pre-5705 devices, multiple link interrupts were being generated
for a single physical link change.  The source of the interrupts was
determined to be unnecessary toggling of the MAC link polarity bit.

This patch changes the way the link polarity bit gets configured.  Where
possible, code that dynamically configures the bit in response to link
changes has been replaced by code that configures the bit once during
initialization time and then leaves the bit alone.

For correctness, this patch also limits the use of the bit to those
devices where it is defined, namely devices before the 5705.  This patch
also corrects the link polarity configurations for 5700 devices when
paired against a bcm5411 phy.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gagan Arneja <gaagaan@gmail.com> pointed out that tg3_reset_task()
could potentially race with another thread calling tg3_full_lock()
such as the ethtool_set_xxx() functions.  This may trigger the
BUG_ON() in tg3_irq_quiesce() or cause the irq_sync flag to be out-
of-sync.

I think the easiest way to fix this is to get the tp->lock first
before setting the irq_sync flag.  This is safe to do because the
tp->lock is never grabbed by the irq handler.  This change will
guarantee that the irq_sync flag updates will be serialized.  We also
have to change one spot to call tg3_netif_start() (which clears the
irq_sync flag) before releasing the tp->lock.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch from formatting messages in probe routine and copying with
kfifo, to using a small circular queue of information and formatting
on read.  This avoids wraparound issues with kfifo, and saves one
copy.

Also make sure to state correct license, rather than copying off some
other driver I started with.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers need to validate the initial addresses in their netlink attribute
validation function or manually reject them if they can't support this.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All drivers need to unregister their devices in the module unload function.
While doing so they must hold the rtnl and atomically unregister the
rtnl_link ops as well. This makes the rtnl_link_unregister function that
takes the rtnl itself completely useless.

Provide default newlink/dellink functions, make __rtnl_link_unregister and
rtnl_link_unregister unregister all devices with matching rtnl_link_ops and
change the existing users to take advantage of that.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VLAN MAC address handling is broken in multiple ways. When the address
differs when setting it, the real device is put in promiscous mode twice,
but never taken out again. Additionally it doesn't resync when the real
device's address is changed and needlessly puts it in promiscous mode when
the vlan device is still down.

Fix by moving address handling to vlan_dev_open/vlan_dev_stop and properly
deal with address changes in the device notifier. Also switch to
dev_unicast_add (which needs the exact same handling).

Since the set_mac_address handler is identical to the generic ethernet one
with these changes, kill it and use ether_setup().
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep netpoll/poll_napi from messing with the poll_list.
Only net_rx_action is allowed to manipulate the list.
Signed-off-by: NOlaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Throw out the old mark & sweep garbage collector and put in a
refcounting cycle detecting one.

The old one had a race with recvmsg, that resulted in false positives
and hence data loss.  The old algorithm operated on all unix sockets
in the system, so any additional locking would have meant performance
problems for all users of these.

The new algorithm instead only operates on "in flight" sockets, which
are very rare, and the additional locking for these doesn't negatively
impact the vast majority of users.

In fact it's probable, that there weren't *any* heavy senders of
sockets over sockets, otherwise the above race would have been
discovered long ago.

The patch works OK with the app that exposed the race with the old
code.  The garbage collection has also been verified to work in a few
simple cases.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creating a new connection by sending an unknown chunk type, we
don't transition to a valid state, causing a NULL pointer dereference
in sctp_packet when accessing sctp_timeouts[SCTP_CONNTRACK_NONE].

Fix by don't creating new conntrack entry if initial state is invalid.

Noticed by Vilmos Nebehaj <vilmos.nebehaj@ramsys.hu>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make all initialized struct seq_operations in net/ const
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rémi Denis-Courmont wrote:
> Right. By the way, shouldn't "len" rather be signed in there?
> 
> 		unsigned int len;
> 
> 		/* if we're overly short, let UDP handle it */
> 		len = skb->len - sizeof(struct udphdr);
> 		if (len <= 0)
> 			goto udp;

It should, but the < 0 case can't happen since __udp4_lib_rcv
already makes sure that we have at least a complete UDP header.

Anyways, this patch fixes it.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This trivial patch removes the unneeded pointer idev returned from
__in6_dev_get(), which is never used. The check for NULL can be simply
done by if (__in6_dev_get(dev) == NULL).
Signed-off-by: NMicah Gruber <micah.gruber@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No longer needed.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because reversing RH0 is no longer supported by deprecation
of RH0, let's make IPV6_{RECV,2292}RTHDR boolean options.
Boolean are more appropriate from standard POV.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on <draft-ietf-ipv6-deprecate-rh0-00.txt>.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "fix" for emerging security threat was overkill and it broke
basic semantic of IPv6 routing header processing.  We should assume
RT0 (or even RT2, depends on configuration) as "unknown" RH type so
that we
- silently ignore the routing header if segleft == 0
- send ICMPv6 Parameter Problem message back to the sender,
  otherwise.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the HTB scheduler does not correctly account for TSO packets
which causes large inaccuracies in the bandwidth control when using TSO.
This patch allows the HTB scheduler to work with TSO enabled devices.
Signed-off-by: NRanjit Manomohan <ranjitm@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rusty (whose comments we should all study and emulate :) pointed
out that our comments for skb checksums are no longer up-to-date.
So here is a patch to

1) add the case of partial checksums on input;
2) update partial checksum case to mention csum_start/csum_offset;
3) mention the new IPv6 feature bit.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To better support and handle eSCO links in the future a bunch of
constants needs to be added and some basic routines need to be
updated. This is the initial step.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Jarek Poplawski <jarkao2@o2.pl>, the timer removal in
gen_kill_estimator races with the timer function rearming the timer.

Check whether the timer list is empty before rearming the timer
in the timer function to fix this.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Acked-by: NJarek Poplawski <jarkao2@o2.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

93ec2c72 applied excessive duct tape to
the netpoll beast's netpoll_cleanup(), thus substituting one leak with
another, and opening up a little buglet :-)

net_device->npinfo (netpoll_info) is a shared and refcounted object and
cannot simply be set NULL the first time netpoll_cleanup() is called.
Otherwise, further netpoll_cleanup()'s see np->dev->npinfo == NULL and
become no-ops, thus leaking. And it's a bug too: the first call to
netpoll_cleanup() would thus (annoyingly) "disable" other (still alive)
netpolls too. Maybe nobody noticed this because netconsole (only user
of netpoll) never supported multiple netpoll objects earlier.

This is a trivial and obvious one-line fixlet.
Signed-off-by: NSatyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there is no Kconfig variable RXRPC anywhere in the tree, and the
variable AF_RXRPC performs exactly the same function, remove the
reference to CONFIG_RXRPC from net/Makefile.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDan Aloni <da-x@monatomic.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VLSI 82C147 IrDA controller driver uses a semaphore as mutex.  Use the
mutex API instead of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- save 4 bytes

- it's read-mostly.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NVasily Averin <vvs@sw.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>