82598 cards and up support DCA, which enables the chipset to warm
up the caches for upcoming payload data. This code makes the
driver plug into the CONFIG_DCA infrastructure that was merged
earlier.
Signed-off-by: NJeb Cramer <cramerj@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

82598 can produce a formidable interrupt rate, and is largely
unusable without some form of moderation. The default behaviour
before this patch is to limit irq's to a reasonable number.
However, just like our other drivers we can reduce latency
for small packet-type traffic considerably by allowing the
irq rate to go up dynamically.

This patch introduces a simple irq moderation algorithm based
on traffic analysis. The driver will use more CPU to service
small packets quicker but will perform the same on bulk traffic
as the old code.
Signed-off-by: NAyyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Now that the irq vector code is in place, we can add the conditional
multiqueue TX code in the driver. This requires the optional
CONFIG_NETDEVICES_MULTIQUEUE=y and will not be enabled without
it.
Signed-off-by: NAyyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NWaskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This code abstracts the per-queue MSI-X interrupt vector into
a queue vector layer. This abstraction is needed since there can
be many more queues than available MSI-X vectors in a machine.

The MSI-X irq vectors are remapped to a shared queue vector which
can point to several (both RX and TX) hardware queues. The NAPI
algorithm then cleans the appropriate ring/queues on interrupt
or poll.

The remapping is a delicate and complex calculation to make sure
that we're not unbalancing the irq load, and spreads the irqs
as much as possible, and may combine RX and TX flows onto the
same queue vector.

This effectively enables receive flow hashing across vectors
and helps irq load balance across CPUs.
Signed-off-by: NAyyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NWaskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: NJon Schindler <jkschind@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: NJon Schindler <jkschind@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: NJon Schindler <jkschind@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: NJon Schindler <jkschind@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replaced init_module and cleanup_module with static functions and module_init/module_exit.
Signed-off-by: NJon Schindler <jkschind@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Removes superh board specific configuration from the header file. These boards
will instead be configured using platform data.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch makes sure SMC_insw()/SMC_outsw() are defined for the
default configuration. Without this change BUG()s will be triggered
when using 16-bit only platform data and the default configuration.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch introduces struct smc91x_platdata and modifies the driver so
bus width is checked during run time using SMC_nBIT() instead of
SMC_CAN_USE_nBIT.

V2 keeps static configuration lean using SMC_DYNAMIC_BUS_CONFIG.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Pass a private data pointer to macros and functions. This makes it easy
to later on make run time decisions. This patch does not change any logic.
These changes should be optimized away during compilation.

V2 changes the macro argument name from "priv" to "lp".
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Updated version number.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Resubmit #3
- Added s2io_vlan_rx_kill_vid entry point function for unregistering vlan.
- Fix to aggregate vlan packets. IP offset is incremented by
  4 bytes if the packet contains vlan header.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Resubmit #2
- Transmit fifo selection based on TCP/UDP ports.
- Added tx_steering_type loadable parameter for transmit fifo selection.
  0x0 NO_STEERING: Default FIFO is selected.
  0x1 TX_PRIORITY_STEERING: FIFO is selected based on skb->priority.
  0x2 TX_DEFAULT_STEERING: FIFO is selected based on L4 Ports.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Resubmit #3
Multiqueue netwrok device support implementation.
- Added a loadable parameter "multiq" to enable/disable multiqueue support,
  by default it is disabled.
- skb->queue_mapping is not used for queue/fifo selection. FIFO selection is
  based on skb->priority.
- Added per FIFO flags FIFO_QUEUE_START and FIFO_QUEUE_STOP. Check this flag
  for starting and stopping netif queue and update the flags accordingly.
- In tx_intr_handler added a check to ensure that we have free TXDs before wak-
  ing up the queue.
- Added helper functions for queue manipulation(start/stop/wakeup) to invoke
  appropriate netif_ functions.
- Calling netif_start/stop for link up/down case respectively.

- As per Andi kleen's review comments, using skb->priority field for FIFO
  selection.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove all obsolete qeth files.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

List of major changes and improvements:
 no manipulation of the global ARP constructor
 clean code split into core, layer 2 and layer 3 functionality
 better exploitation of the ethtool interface
 better representation of the various hardware capabilities
 fix packet socket support (tcpdump), no fake_ll required
 osasnmpd notification via udev events
 coding style and beautification
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ctc driver is replaced by a new ctcm driver.
The ctcm driver supports the channel-to-channel connections of the
old ctc driver plus an additional MPC protocol to provide SNA
connectivity.
This patch removes the functions of the old ctc driver.
Signed-off-by: NPeter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ctcm driver supports the channel-to-channel connections of the
old ctc driver plus an additional MPC protocol to provide SNA
connectivity.

This new ctcm driver replaces the existing ctc driver.
Signed-off-by: NPeter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

adapt drivers/s390/net/Kconfig to current IBM wording
and further cosmetics
Signed-off-by: NPeter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rearrange functions to allow removal of some forward declarations.
Make certain global functions static along the way.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make needlessly global functions static.  In a couple of cases this
requires removing forward declarations and reordering functions.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add some debug printks if we encounter a potentially bad receive
return descriptor.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use netif_msg_* for console messages emitted by the driver. Add a
parameter to allow control of messaging at driver startup, and also
add the ability to control it with ethtool.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use skb->csum_start for tx checksum offload preparation. Also swap
the variables css and cso so they hold the intended values of csum
start and offset, respectively.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The transmit packet descriptor consists of four 32-bit words, with word 3
upper bits overloaded depending upon the condition of its bits 3 and 4.
The driver currently duplicates all word 2 and some word 3 register bit
definitions unnecessarily and also uses a set of nested structures in its
definition of the TPD without good cause. This patch adds a lengthy
comment describing the TPD, eliminates duplicate TPD bit definitions,
and simplifies the TPD structure itself. It also expands the TSO check
to correctly handle custom checksum versus TSO processing using the revised
TPD definitions. Finally, shorten some variable names in the transmit
processing path to reduce line lengths, rename some variables to better
describe their purpose (e.g., nseg versus m), and add a comment or two
to better describe what the code is doing.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add the ethtool register dump option to the atl1 driver.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The L1 tx packet descriptor expects TCP Header Length to be expressed as a
number of 32-bit dwords.  The atl1 driver uses tcp_hdrlen() to populate the
field, but tcp_hdrlen() returns the header length in bytes, not in dwords.
Add a shift to convert tcp_hdrlen() to dwords when we write it to the tpd.

Also, some of our bit assignments are made to the wrong tpd words.  Change
those to the correct words.

Finally, since all this fixes TSO, enable TSO by default.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The future atl2 driver and the existing atl1 driver can share certain
functions and definitions.  Move these shareable functions and definitions
out of atl1-specific files and into atlx.c and atlx.h.  Some transitory
hackery will be present until atl2 is merged.

Reduce the number of source files by moving ethtool, hw, and param
functions from separate files into atl1_main.c, then rename it to just
atl1.c.

Move all atl1-specific definitions from atl1_hw.h to atl1.h.

Finally, clean up to make checkpatch.pl happy.
Signed-off-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In preparation for a future Atheros L2 NIC driver (called atl2), relocate
the atl1 driver into a new /drivers/net/atlx directory that will ultimately
be shared with the future atl2 driver.
Signed-off-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The xircom_tulip_cb driver has been replaced the xircom_cb driver, and
since it depended on BROKEN_ON_SMP it e.g. was no longer present in many
distribution kernels.

This patch therefore removes it.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  [PARISC] make ptr_to_pide() static
  [PARISC] head.S: section mismatch fixes
  [PARISC] add back Crestone Peak cpu
  [PARISC] futex: special case cmpxchg NULL in kernel space
  [PARISC] clean up show_stack
  [PARISC] add pa8900 CPUs to hardware inventory
  [PARISC] clean up include/asm-parisc/elf.h
  [PARISC] move defconfig to arch/parisc/configs/
  [PARISC] add back AD1889 MAINTAINERS entry
  [PARISC] pdc_console: fix bizarre panic on boot
  [PARISC] dump_stack in show_regs
  [PARISC] pdc_stable: fix compile errors
  [PARISC] remove unused pdc_iodc_printf function
  [PARISC] bump __NR_syscalls
  [PARISC] unbreak pgalloc.h
  [PARISC] move VMALLOC_* definitions to fixmap.h
  [PARISC] wire up timerfd syscalls
  [PARISC] remove old timerfd syscall

Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
Signed-off-by: NHelge Deller <deller@gmx.de>
SIgned-off-by: NKyle McMartin <kyle@mcmartin.ca>

Crestone Peak Slow is the 800MHz PA-8800 cpu in the C8000.
0x88B is probably the Crestone Peak Fast.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Commit a0c1e907 added code to futex.c
to detect whether futex_atomic_cmpxchg_inatomic was implemented at run
time:

+       curval = cmpxchg_futex_value_locked(NULL, 0, 0);
+       if (curval == -EFAULT)
+               futex_cmpxchg_enabled = 1;

This is bogus on parisc, since page zero in kernel virtual space is the
gateway page for syscall entry, and should not be read from the kernel.
(That, and we really don't like the kernel faulting on its own address
 space...)
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>