Disable the USB_MULTITHREAD_PROBE option because it causes crashes on
people's machines and they never remember to actually read the config
help files.

No one likes this, everyone hates it, I'm going to go eat worms...

The full logic will be ripped out later.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7814Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

American Megatrends did something wrong in their floppy emulator. It breaks
with both kinds of MODE SENSE which our stack sends. Alan and I tried a few
tweaks, and got LUNs sensed right, but US_FL_NO_WP_DETECT is still needed.

I set the firmware bracket to 1.00 exactly, in case AMI or Sun fix it with a
firmware update. Hey, you never know.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

on request of the sourceforge project for this device, a kind of
robotized CD storage, it should be ignored by the generic driver.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Bug fix for driver rndis_host which fixes rndis_host probing certain
Nokia S60 (Series 60) mobiles. While the rndis_host get probed by usbnet
and tries to bind the Nokia mobile the bind is going to fail. The
rndis_host module tries to release the device, in a wrong way, which
cause the oops.

Fixes Bugzilla #7201
Signed-off-by: NDaniel Gollub <dgollub@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Different AX88772 dongles use different PHYs; the chip is capable of using
both a primary and secondary PHY, and supports an internal and external PHY.

It appears that some DUB-E100 devices use the internal PHY, so trying to use
an external one will not work (note that this is different across revisions,
as well; the "A" and "B" revs of the DUB-E100 use different PHYs!).  The data
sheet for the AX88772 chip specifies that the internal PHY id will be 0x10,
so if that's read from the EEPROM, we should use that rather than attempting
to use an external PHY.

Thanks to Mitch Bradley for pointing this out!
Signed-off-by: NAndres Salomon <dilinger@debian.org>
Cc: David Hollis <dhollis@davehollis.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ITM screens send invalid x/y data when not touched. this was fixes a while ago
but the problem is if the screen is not touched anymore the driver never does
not report BTN_TOUCH as zero. fix it by sending the report with the last valid
coordinates when pressure is released.
Signed-off-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Cc: J.P. Delport <jpdelport@csir.co.za>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (30 commits)
  [SCSI] qla1280: set residual correctly
  [SCSI] fusion: bump version
  [SCSI] fusion: MODULE_VERSION support
  [SCSI] fusion: power pc and miscellaneous bug fixs
  [SCSI] fusion: fibre channel: return DID_ERROR for MPI_IOCSTATUS_SCSI_IOC_TERMINATED
  [SCSI] megaraid_sas: Update module author
  [SCSI] 3ware 8000 serialize reset code
  [SCSI] sr: fix error code check in sr_block_ioctl()
  [SCSI] scsi: lpfc error path fix
  [SCSI] aacraid: Product List Update
  [SCSI] libiscsi: fix senselen calculation
  [SCSI] iscsi: simplify IPv6 and IPv4 address printing
  [SCSI] iscsi: newline in printk
  [SCSI] iscsi: fix crypto_alloc_hash() error check
  [SCSI] iscsi: fix 2.6.19 data digest calculation bug
  [SCSI] scsi_scan: fix report lun problems with CDROM or RBC devices
  [SCSI] qla2xxx: Update version number to 8.01.07-k4.
  [SCSI] qla2xxx: Use generic isp_ops.fw_dump() function.
  [SCSI] qla2xxx: Perform a fw-dump when an ISP23xx RISC-paused state is detected.
  [SCSI] qla2xxx: Correct reset handling logic.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  hid-core.c: Adds GTCO CalComp Interwrite IPanel PIDs to blacklist
  HID: put usb_interface instead of usb_device into hid->dev to fix udevinfo breakage
  HID: add missing RX, RZ and RY enum values to hid-debug output
  HID: hid/hid-input.c doesn't need to include linux/usb/input.h
  HID: compilation fix when DEBUG_DATA is defined
  HID: proper LED-mapping for SpaceNavigator
  HID: update MAINTAINERS entry for USB-HID
  HID: GEYSER4_ISO needs quirk
  HID: fix some ARM builds due to HID brokenness - make USB_HID depend on INPUT

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Update defconfigs
  [POWERPC] atomic_dec_if_positive sign extension fix
  [POWERPC] Fix OF node refcnt underflow in 836x and 832x platform code
  [POWERPC] Make it blatantly clear; mpc5200 device tree is not yet stable
  [POWERPC] Fix broken DMA on non-LPAR pSeries
  [POWERPC] Fix cell's mmio nvram to properly parse device tree
  [POWERPC] Remove bogus sanity check in pci -> OF node code

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Delete duplicate call to load_irq_save.
  [MIPS] SMTC: Fix cp0 hazard.

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon/w83793: Hide invalid VID readings
  hwmon/w83793: Fix the fan input detection
  hwmon/w83793: Ignore disabled temperature channels
  hwmon: Fix the VRD 11 decoding
  hwmon/w83793: Remove the description of AMDSI and update the voltage formula

* git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs-2.6:
  NTFS: Forgot to bump version number in makefile to 2.1.28...
  NTFS: 2.1.28 - Fix deadlock reported by Sergey Vlasov due to ntfs_put_inode().

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (5023): Fix compilation on ppc32 architecture
  V4L/DVB (5071): Tveeprom: autodetect LG TAPC G701D as tuner type 37
  V4L/DVB (5069): Fix bttv and friends on 64bit machines with lots of memory
  V4L/DVB (5033): MSI TV@nywhere Plus fixes
  V4L/DVB (5029): Ks0127 status flags
  V4L/DVB (5024): Fix quickcam communicator driver for big endian architectures
  V4L/DVB (5021): Cx88xx: Fix lockup on suspend
  V4L/DVB (5020): Fix: disable interrupts while at KM_BOUNCE_READ
  V4L/DVB (5019): Fix the frame->grabstate update in read() entry point.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: Correct definition of R6
  omap: Update MMC response types

This reverts commit 99a10a60.

As per Hugh Dickins:

  "Nadia Derbey has reported that mmap of /dev/kmem no longer works with
   the kernel virtual address as offset, and Franck has confirmed that
   his patch came from a misunderstanding of what an offset means to
   /dev/kmem - whereas his patch description seems to say that he was
   correcting the offset on a few plaforms, there was no such problem to
   correct, and his patch was in fact changing its API on all platforms."
Suggested-by: NHugh Dickins <hugh@veritas.com>
Cc: Franck Bui-Huu <fbuihuu@gmail.com>
Cc: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Andi Kleen <ak@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mostly took the defaults, except tried to get the netfilter options
more or less as they were before.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On 64-bit machines, if an atomic counter is explicitly set to a
negative value, the atomic_dec_if_positive function will decrement and
store the next smallest value in the atomic counter, contrary to its
intended operation.

The comparison to determine if the decrement will make the result
negative was done by the "addic." instruction, which operates on a
64-bit value, namely the zero-extended word loaded from the atomic
variable.  This patch uses an explicit word compare (cmpwi) and
changes the addic. to an addi (also changing "=&r" to "=&b" so that r0
isn't used, and addi doesn't become li).

This also fixes a bug for both 32-bit and 64-bit in that previously
0x80000000 was considered positive, since the result after
decrementing is positive.  Now it is considered negative.

Also, I clarify the return value in the comments just to make it clear
that the value returned is always the decremented value, even if that
value is not stored back to the atomic counter.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Incorrect use of of_find_node_by_name() causes of_node_put()
on a node which has already been put.  It causes the refcount of
the node to underflow, which triggers the WARN_ON in kref_get
for 836x and 832x.  This fixes it.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Documentation-only change.  The 5200 device tree layout has not yet
stablized, so nobody should depend on the layout of the tree.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSylvain Munaut <tnt@246tNt.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It appears that the iommu table address is never stored, and thus
never found, on non-lpar systems. Thus, for example, during boot:

<7>[   93.067916] PCI: Scanning bus 0001:41
<7>[   93.068542] PCI: Found 0001:41:01.0 [8086/100f] 000200 00
<7>[   93.068550] PCI: Calling quirk c0000000007822e0 for 0001:41:01.0
<7>[   93.069815] PCI: Fixups for bus 0001:41
<4>[   93.070167] iommu: Device 0001:41:01.0 has no iommu table
<7>[   93.070251] PCI: Bus scan for 0001:41 returning with max=41

No iommu table? How can that be? Well, circa line 471 of
arch/powerpc/platforms/pseries/iommu.c we see the code:

   while (dn && PCI_DN(dn) && PCI_DN(dn)->iommu_table == NULL)
      dn = dn->parent;

and a few lines later is the surprising print statement about
the missing table.  Seems that this loop ran unto the end, never
once finding a non-null PCI_DN(dn)->iommu_table.

The problem can be found a few lines earlier: it sems that the
value of PCI_DN(dn)->iommu_table is never ever set. Thus, the
patch sets it.

The patch was tested on a Power4 system running in full system
partition mode, which is where I saw the problem. It works; I've
not done any wider testing. Had a brief discussion on this on irc.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The mmio nvram driver (used by cell only atm) isn't properly parsing
the device-tree, meaning that nvram isn't found correctly on the new
Cell blades.  It works ok for old blades where the nvram is at the
root of the device tree but fails on Malta and CAB when it's hanging
off axon.  This fixes it by using the proper OF parsing functions.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The new implementation of pci_device_to_OF_node() on ppc32 has a bogus
sanity check in it that can cause oopses at boot when no device node is
present, and might hit correct cases with older/weird apple device-trees
where they have the type "vci" for the chaos bridge.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Adds GTCO CalComp Interwrite IPanels to the hid-core.c blacklist.
Signed-off-by: NJeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The commit 4916b3a5 introduced a
hid regression between 2.6.19 and 2.6.20-rc1. The device put in
input_dev->cdev is now of type usb_device instead of usb_interface.

Before:
> # readlink -f /sys/class/input/input6/event4/device
> /sys/devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.1
After:
> # readlink -f /sys/class/input/input3/event3/device
> /sys/devices/pci0000:00/0000:00:10.0/usb1/1-1

This causes breakage:
> # udevinfo -q all -n /dev/input/event3
> P: /class/input/input3/event3
> N: input/event3
> S: input/by-path/pci-1-1--event-
> E: ID_SERIAL=noserial
> E: ID_PATH=pci-1-1-

No ID_MODEL, ID_VENDOR, ID_REVISION, ID_TYPE etc etc.

Fix this by assigning the intf->dev into hid->dev, and fixing
all the users.
Signed-off-by: NAnssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This trivial change adds some missing enum values to the hid-debug output.
Signed-off-by: NSimon Budig <simon@budig.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There is no reason for generic hid-input.c to include usb-specific
input.h.

As a sideeffect, this also fixes warning of redefinition of dbg()
macro, when hid-input.c is compiled with DEBUG (as there is a clash
between dbg() from hid.h and usb/input.h).
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid/hid-core.c references 'len' variable when DEBUG_DATA is defined,
but the actual name of the variable is 'size'. Fix it.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This change introduces a mapping for LED indicators between the HID
specification and the Linux input subsystem. The previous code properly
mapped the LEDs relevant for Keyboards, but garbeled the remaining ones.
With this change all LED enums from the input system get mapped to more
or less equivalent LED numbers from the HID specification.

This patch also ensures that the unused bits in a HID report to the
device are zeroed out. This makes the 3Dconnexion SpaceNavigator fully
usable with the linux input system.
Signed-off-by: NSimon Budig <simon@budig.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Change USB-HID maintainer from Vojtech Pavlik to Jiri Kosina.
Acked-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

I've got a newer MacBook with core2duo. Two keys on the keyboard are
swapped, "unswaping" works with the same trick as GEYSER3_ISO.
Signed-off-by: NAdrian Friedli <masteradi@gmx.ch>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

We have USB_HID _newly_ selected in configurations which didn't
have it before, which overrides CONFIG_HID and builds HID without
input support.

Nevertheless, here's a patch to solve more of the same that my original
patch attempted to solve.  The original patch is still required.  Seems
to solve the final instance of this problem here.
Signed-off-by: NRussell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This call may have resulted to local_tlb_flush_range returning with
interrupts disabled resulting in excessive interrupt latency.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Ignore the VID readings when the motherboard has not designed
the function.  
Signed-off-by: NGong Jun <jgong@winbond.com>
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Catch the cases when alternative pins are used to route the
fan9-12 input.
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NGong Jun <jgong@winbond.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Ignore the temperature readings when its channel is disabled,
ignore AMDSI readings.
Signed-off-by: NGong Jun <jgong@winbond.com>
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

I wonder how we came up with such a broken test in the first place.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fix the driver to match the information in datasheet 1.0. AMD 
SI interface is marked as reserved, computing formula for 5VDD
and 5VSB is updated.
Signed-off-by: NGong Jun <jgong@winbond.com>
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NAnton Altaparmakov <aia21@cantab.net>