This reverts commit ac162362.

It was premature to remove it now, we will do it post-2.6.26.

Thanks to Russell King for noticing the issue.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The newly added event_lock spinlock in the input core disallows sleeping
and therefore using mutexes in event handlers. Convert force-feedback
core to rely on event_lock instead of mutex to protect slots allocated
for fore-feedback effects. The original mutex is still used to serialize
uploading and erasing of effects.
Reported-by: NAnssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There is a small off-by-one bug in firewire-sbp2. This causes problems
when a device exports multiple LUN Directories. I found it when trying
to talk to a SONY DVD Jukebox.
Signed-off-by: NRichard Sharpe <realrichardsharpe@gmail.com>
Acked-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (op. order, changelog)

The saa7134 driver uses a (non-atomic) variable in an attempt to
only allow one opener of the device (how it deals with sending
the fd over unix sockets I don't know).

Unfortunately, the release function first decrements this variable,
and THEN goes on to disable more of the device. This allows for
a race where another opener of the device comes in after the decrement of
the variable, configures the hardware just to then see the hardware
be disabled by the rest of the release function.

This patch makes the release function use the same lock as the open
function to protect the hardware as well as the variable (which now
at least has some locking to protect it).
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Move allocation after first check and fix memory leak.
Noticed-by: NDaniel Marjamäki <danielm77@spray.se>
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch ensures that the xc5000 will have firmware loaded as needed if the
part is powered down or reset via gpio from the host. An example of this, in
some cases, could be after the system resumes from standby or hibernate modes.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This decreases scan time in Queens, New York from 28 minutes to 7 minutes,
with the exact same services found.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

VIDIOC_ENUMSTD did not return all the PAL/SECAM/NTSC variants: it just returned
one single PAL/SECAM/NTSC standard without separate entries for the trickier
standards like NTSC-JP.

Changed the code so that it behaves better.

Also simplified the if/switch statements into a common standards lookup table.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix uncorrected block counter and bit error rate to follow DVB API spec:
- Unsupported controls return -ENOSYS.
- UNC must never be set to 0.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

OSD transfers should not be interrupted.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Catch another type of ARM crash.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If the i2c write fails during initialisation, an oops happens
because state->frontend.dvb is still undefined. Fixed.

Thanks to Sigmund Augdal for reporting this bug,
and to Hartmut Birr for suggesting the fix.

Thanks-to: Sigmund Augdal <sigmund@snap.tv>
Thanks-to: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user
reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and
Brian Hope <brian@hopefamily.info> and enable the card entry.  The tuner reset
GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a
reboot.  It is likely the audio routing is done via GPIO which is not
implemented yet, as users report audio doesn't work for some inputs.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cx18: Add I2C slave reset via GPIO upon initialization.  One user,
Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to
be consistently recognized when using (long,) 100 msec delays.   The delays in
this commit are nominal (10 & 40 msec) and need testing/tuning on boards with
I2C problems to find the right values.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This is a fix for the case when a digital capture from dvr0 happens first after
modprobe, before access to any cx18 v4l2 device nodes.  The initial dvb feed
start has been changed to load the firmware if not already loaded.  Also fixed a
use counter to correct dvb feed accounting if starting the transport DMA fails.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2
and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively.  Verified
by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the
HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843.  This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The automatic Kconfig selection for tuners and frontends should be
conditional, based on !DVB_FE_CUSTOMISE.

This patch corrects the selection for VIDEO_CX18 on
MEDIA_TUNER_MXL5005S and DVB_S5H1409
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Also, adds IR table for Avermedia A16d
Signed-off-by: NTim Farrington <timf@iinet.net.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.

Don't store current frequency until after we've tuned successfully.

Force a re-tune after resume from standby.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20.  But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.

Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.

fix on Kaffeine channel scan for

Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: Nmaximilian attems <max@stro.at>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz.  In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner.  Move the IF notch configuration to after we update MPD.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:

tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5

Now, instead of reporting an invalid ID, it will report the correct error:

tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed

A possible improvement would be trying to reset the device.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:

DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed

Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.

With this patch, it will now print:

Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed

Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

On some alsa versions, it seems that snd_pcm_substream_chip(substream)
is returning a NULL pointer. This causes an OOPS, as reported by:

https://bugs.launchpad.net/ubuntu/+source/linux-ubuntu-modules-2.6.24/+bug/212271
https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/212960

This patch avoids the OOPS by not letting and open() succeed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If I try v4l2-ctl --all -d /dev/video1 or v4l2-ctl --streamon -d /dev/video1
modules crashed:

*pde = 00000000
Modules linked in: ac battery loop saa7134_empress(F) saa6752hs(F) tuner_simple(F) tuner_types(F) tea5767(F) tda9887(F) tda8290(F) tea5761(F) tuner(F) snd_cmipci snd_pcm snd_page_alloc snd_opl3_lib saa7134(F) snd_mpu401 parport_pc parport snd_timer snd_hwdep snd_mpu401_uart floppy rtc psmouse videodev(F) v4l1_compat(F) compat_ioctl32(F) v4l2_common(F) videobuf_dma_sg(F) videobuf_core(F) snd_rawmidi snd_seq_device via_ircc pcspkr snd ir_kbd_i2c(F) irda soundcore ir_common(F) crc_ccitt tveeprom(F) i2c_viapro i2c_core button via_agp agpgart evdev ext3 jbd mbcache ide_cd_mod cdrom ide_disk 8139cp via82cxxx ide_core 8139too mii ehci_hcd uhci_hcd usbcore thermal processor fan

EIP is at __mutex_lock_slowpath+0x29/0x7b
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process v4l2-ctl (pid: 2742, ti=ced7e000 task=cf325260 task.ti=ced7e000)
       d08e5411 00000000 ced7fed4 00000000 d0975acb 40045612 cfa86ee0 ffffffcd
       cf2b7000 ced7febc c03858d6 00000019 00000292 d089e4ec cf37b2a0 d089e4a0
Call Trace:
 [<c028b52b>] mutex_lock+0xa/0xb
 [<d08e5411>] videobuf_streamon+0xf/0x9a [videobuf_core]
 [<d0975acb>] __video_do_ioctl+0x136a/0x2d68 [videodev]
 [<d088f789>] task_end_request+0x40/0x51 [ide_core]
 [<d088c4aa>] ide_intr+0x187/0x192 [ide_core]
 [<c016a551>] mntput_no_expire+0x11/0x64
 [<c0160b1c>] path_walk+0x90/0x98
 [<d0977738>] video_ioctl2+0x173/0x239 [videodev]
 [<c0140936>] filemap_fault+0x202/0x370
 [<c014930a>] __do_fault+0x2c3/0x2fe
 [<c014ab03>] handle_mm_fault+0x22a/0x49f
 [<c0162737>] vfs_ioctl+0x47/0x5d
 [<c0162992>] do_vfs_ioctl+0x245/0x258
 [<c01629e6>] sys_ioctl+0x41/0x5b
 [<c01036a6>] sysenter_past_esp+0x5f/0x85
 =======================

After this fix all of that commands works without problem:

v4l2-ctl --all -d /dev/video1

Driver Info:
	Driver name   : saa7134
	Card type     : Beholder BeholdTV M6 Extra
	Bus info      : PCI:0000:00:0d.0
	Driver version: 526
	Capabilities  : 0x05000001
		Video Capture
		Read/Write
		Streaming
Format Video Capture:
	Width/Height  : 720/576
	Pixel Format  : MPEG
	Field         : Any
	Bytes per Line: 0
	Size Image    : 58656
	Colorspace    : Unknown (00000000)
Video input : 0 (CCIR656)
Video Standard = 0x000000ff
	PAL-B/B1/G/H/I/D/D1/K


P.S. data from /dev/video1 is not correct :(( .
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

em28xx-cards.c
em28xx-reg.h
 - Add em2860 chip ID (seen on Pointnix Intra-Oral Camera)
   http://www.pointnix.com/ENG/dental/product_02.aspSigned-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

em28xx-audio.c
em28xx-dvb.c
 - Em28xx extensions should ensure they are being only loaded against devices
   that support them.  Deals with case where there are multiple em28xx
   devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- change msleep(0) to msleep(1)
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- remove useless identify_state - device is always warm
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- add little sleep to avoid I2C errors arising on faster CPUs
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

em28xx-cards.c
 - DVB support is supposed to be enabled for the first generation HVR-900.
   This device was confirmed with DVB by mkrufky when we did the original work
   in April, but I guess we forgot to set the flag.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>