Remove usb_ep_{alloc,free}_buffer() calls, for small dma-coherent buffers.
This patch just removes the interface and its users; later patches will
remove controller driver support.

  - This interface is invariably not implemented correctly in the
    controller drivers (e.g. using dma pools, a mechanism which
    post-dates the interface by several years).

  - At this point no gadget driver really *needs* to use it.  In
    current kernels, any driver that needs such a mechanism could
    allocate a dma pool themselves.

Removing this interface is thus a simplification and improvement.

Note that the gmidi.c driver had a bug in this area; fixed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cleanups to the pxa2xx_udc code:

  - Primarily removing unused DMA hooks.
  - One "sparse" warning removed
  - Remove some Lubbock-only LED hooks (for debugging)

That DMA code was never really completed.  It worked, mostly, for IN
transfers (to the host) if they were fortuitously aligned, but that
code was never fully tested.  And it was never coded for OUT transfers
(which is where DMA would really help) ... because of chip errata on
essentially every chip other than the pxa255, and because of design
botches (nothing automated data toggle).  So it's effectively been
dead code for several years now ... no point in keeping it around.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch lets the pxa2xx_udc use the generic gpio layer,
on the relevant PXA and IXP systems.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this printer does not survive suspension.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates some of the documentation about DMA buffer management
for USB, and ways to avoid extra copying.  Our understanding of the issues
has improved over time.

 - Most drivers should *avoid* the dma-coherent allocators.  There are
   a few exceptions (like the HID driver).

 - Some methods are currently commented out; it seems folk writing
   USB drivers aren't doing performance tuning at that level yet.

 - Just avoid highmem; there's no good way to pass an "I can do highmem
   DMA" capability through a driver stack.  This is easy, everything
   already avoids highmem.  But it'd be nice if x86_32 systems with much
   physical memory could use it directly with network adapters and mass
   storage devices.  (Patch, anyone?)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Following patch removes trailing whitespaces at the ends of lines and converts
smarttabs/whitespaces into real tabs.
Signed-off-by: NS.Caglar Onur <caglar@pardus.org.tr>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The MOS driver is "interesting", in a bad kind of 'how the hell did this
get merged' kind of way

- Remove the bogus termios change check
- Remove the duplicate code for half the ioctls
- Remove the supporting code to duplicate the ioctl code
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

So we can use dev_to_node(&usb_dev->dev) later in kmalloc_node to dma buffer
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: NChristoph Lameter <clameter@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix an oops that happens in relation with applying work arounds for buggy
ftdi_sio devices.  The quirks were handled too early because due to changes in
the initialisation of usb serial devices the device was not fully initialised
when the old hook was called.

Addresses bug 8564

Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Low performance USB storage driver: Use list_for_each_entry() instead
of list_for_each()
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Generally, Jens Axboe was against 'default y', so I'll have some patches to
remove it.

Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make usb autosuspend timers 1sec jiffy aligned.

This helps to reduce the frequency at which the CPU must be taken out of a
lower-power state.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Blackberry devices charge over USB.  By autosuspending the port, they are
not able to charge reliably.
Signed-off-by: NJeremy Katz <katzj@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Blackberry Pearl (8100) needs similar tweaks as older Blackberry models
to be able to charge when connected via USB.  The Pearl also adds an
additional need to go into a separate mode for fully accessing the device;
do that by default as well.

Changes based on the changes from bcharge in the barry project
(http://barry.sf.net)
Signed-off-by: NJeremy Katz <katzj@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB_IAD: Adds support for USB Interface Association Descriptors.

This patch adds support to the USB host stack for parsing, storing, and
displaying Interface Association Descriptors. In /proc/bus/usb/devices
lines starting with A: show the fields in an IAD. In sysfs if an
interface on a USB device is referenced by an IAD the following files
will be added to the sysfs directory for that interface:
iad_bFirstInterface, iad_bInterfaceCount, iad_bFunctionClass, and
iad_bFunctionSubClass, iad_bFunctionProtocol
Signed-off-by: NCraig W. Nadler <craig@nadler.us>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Update the original developer's email addresses at their request.


Cc: Vijaya Kumar <vijaykumar.gn@gmail.com>
Cc: Ajay Kumar <naanuajay@yahoo.com>
Cc: Gurudeva <ngurudeva@yahoo.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The loop in usb_sg_wait() is structured in a way that makes it hard to
tell, when the loop exits, whether or not the last URB submission
succeeded.  This patch (as928) changes it from a "for" loop to a
"while" loop and keeps "i" always equal to the number of successful
submissions.  This fixes an off-by-one error which can show up when
the first URB submission fails.

The patch also removes a couple of lines that initialize fields which
don't need to be initialized.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Root hubs can't be resumed if their parent controller device is still
suspended.  This patch (as925) adds a check for that condition in
hcd_bus_resume() and prevents it from being treated as a fatal
controller failure.

ehci-hcd is updated to add the corresponding test.  Unnecessary
debugging messages are removed from uhci-hcd and dummy-hcd.  The
error return code from dummy-hcd is changed to -ESHUTDOWN, the same as
the others.  ohci-hcd doesn't need any changes.

Suspend handling in the non-PCI host drivers is somewhat hit-and-miss.
This patch shouldn't have any effect on them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as922) removes all but one of the remaining vestiges of
dev->power.power_state from usbcore.  The only usage left must remain
until the deprecated "power/state" sysfs attribute is gone.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch's main bulk aims to make usblp the premier driver for code
pillaging once again. The code is as streamlined as possible and is bug-free
as possible. The usb-skeleton performs the same function, but is somewhat
abstract. The usblp is usb-skeleton which is actually used by many.

Since I combed a few small bugs away, this also fixes the small races we
had in usblp for a while. For example, now it's possible for several threads
to make write(2) calls (sounds silly, but consider a printer for paper
record, where every line of text is self-contained and thus it's all right
to have them interleaved). Also gone are issues with interrupts using
barriers dangerously.

This patch makes use of Oliver's anchor, and so it must trail the anchor
patch on the way to Linus.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Vojtech agreed to pass usblp over to me, so if you find bugs don't bug him.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a bug that PORT_TYPE and PORT_WIDTH aren't masked correctly in portsc.
Signed-off-by: NChristopher Cason <chris.cason@nec.com.au>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this patch implements autosuspend for the usblcd driver. It uses
the new usb_anchor infrastructure. Many thanks to Georges for testing.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: Georges Toth <g.toth@e-biz.lu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

husb2dev was the internal name of the USB Device Controller on
AT32AP7000. Rename it to "atmel_usba", which is closer to the official
name used in documentation and marketing material.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: Add URB_FREE_BUFFER flag for freeing the transfer buffer

In some cases it is not needed that the driver keeps track of the
transfer buffer of an URB. It can be simply freed along with the
URB itself when the reference count goes down to zero. The new
flag URB_FREE_BUFFER enables this behavior.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Many device manufacturers are using full-speed bInterval values in high-speed
interrupt endpoint descriptors. If the bInterval value is greater than 16,
assume the device uses full-speed descriptors and fix the value accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

use anchors in pre/post_reset
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

use anchors in suspend/resume handling
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

use anchors in disconnect handling
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Drivers don't call ldisc termios methods. They certainly don't call
them the way this one does - remove wrong call
- The tty buffer code isn't designed to be abused from IRQ handlers and
the new buffering removes the need for the uglies involved - fix them
- Style
- Remove incorrect baud and change handling for termios changes

The driver now has some style, but not a lot - it goes insane if you have
two dongles for example as it continues to use global variables for per
dongle state. That bit isn't my problem.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the baud rate stuff from the kernel don't parse CBAUD directly
Remove pointless and wrong 'no change' check

Could do with some good testing as well but again better than adding &&
BROKEN

(The use of BELKIN_SA_BAUD() might seem a bit odd but x/a = b and x/b =
a (rounded for integers)).
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

o	Don't parse the cflag for baud rates, its not valid to do so
	any more and this driver got it wrong anyway
o	Don't do clever termios change checks in drivers and get them
	wrong (arguably we should do some smart ones in the tty core but
	stty to change nothing is *not* a common or critical path

I don't have the hardware so if you can test this carefully please do. I
thought fixing it up this far was better than marking it and other bits of
USB serial && BROKEN
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This removes the ugly code that was copied from the keyspan driver and
allocates the in urbs in a much shorter code path that can be understood
easier.

Also turned off the interrupt urb when no port was open as it's not nice
to keep the bus busy for no good reason at all (this should be a power
savings.)

All in all, this saved over 40 lines of code and cleaned things up
better.

Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

You can't rely on the fact that the status really is correct like it was.

Also simplified the write path and now we allocate the urb and data on
the fly, instead of trying to do that really odd timeout check which I
am guessing doesn't really work properly.  This should speed up the
device by keeping the hardware queue full easier.

As a benefit, this reduces the size of the driver.

Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.


Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>