We should release the lock here and enable IRQs before returning.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
[grant.likely: move unlock above dev_err() call]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

I found that there are two kind of direction type.
First one is dma_data_direction defined in include/linux/dma-direction.h.
It is used for parameter of dma_map/unmap_single in spi-s3c64xx.
The other one is dma_transter_direction defined in include/linux/dmaengine.h.
It is used for direction of samsung DMA operation
(arch/arm/plat-samsung/dma-ops.c).
This patch is just some changes to use direction defines
which is used in samsung DMA operation.
Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently, pch_spi_start_transfer failure is not anticipated.
This patch adds the processing.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch supports a spi mode setup and bit order setup by IO control.
    spi mode:     mode 0 to mode 3
    bit order:    LSB first, MSB first
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently, when spi-topcliff-pch receives transmit request over 4KByte,
this driver can't process correctly. This driver needs to divide the data
into 4Kbyte unit.
This patch fixes the issue.
Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NTomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Simplify the error handling by moving the code to free gpios in one place.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE
tables.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds support for the SPI controller found on the Broadcom BCM63xx
SoCs.
Signed-off-by: NTanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

CSR SiRFprimaII has two SPIs (SPI0 and SPI1). Features:
* Master and slave modes
* 8-/12-/16-/32-bit data unit
* 256 bytes receive data FIFO and 256 bytes transmit data FIFO
* Multi-unit frame
* Configurable SPI_EN (chip select pin) active state
* Configurable SPI_CLK polarity
* Configurable SPI_CLK phase
* Configurable MSB/LSB first
Signed-off-by: NZhiwu Song <zhiwu.song@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Fix for:
drivers/spi/spi-topcliff-pch.c: In function ‘pch_spi_handler_sub’:
drivers/spi/spi-topcliff-pch.c:325:17: warning: ‘bpw_len’ may be
  used uninitialized in this function [-Wuninitialized]
drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘rx_index’ may be
  used uninitialized in this function [-Wuninitialized]
drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘tx_index’ may be
  used uninitialized in this function [-Wuninitialized]

Move usage of tx_index, rx_index and bpw_len into the same
block as where they are set to prevent uninitialized usage.

v2: instead of init variables with 0 move the whole block
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some systems have SPI devices located on plugin modules which are
enumerated at runtime as devices. The drivers for these plugin modules
need to register their SPI devices at probe() time so want to be able
to call spi_register_board_info() but that function is currently marked
as __init rather than __devinit so this usage isn't legal. Change the
annotation to __devinit to handle this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Convert the s3c64xx driver to using the new message queue factored out of
the pl022 driver by Linus Walleij, saving us a nice block of code and
getting the benefits of improvements implemented in the core.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

They are all defined in an if SPI_MASTER ... endif block.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The loop count i traverses for ntrans which is unsigned
so make the loop count i also unsigned.

Fix the below warning
In file included from drivers/spi/spi-omap2-mcspi.c:38:
include/linux/spi/spi.h: In function 'spi_message_alloc':
include/linux/spi/spi.h:556: warning: comparison between signed and unsigned integer expressions

Cc: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.

Most of the design is described in the documentation changes that
are included in this patch.

Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().

ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
  at all, instead be more agressive and have it as part of the
  compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
  deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
  Chris Blair.
Signed-off-by: NChris Blair <chris.blair@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The SH7757 has RSPI module. This patch supports it.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This SPI controller's access size is 32, or 8-bit. The previous driver
supported 32-bit only. So, this patch adds IORESOURCE_MEM_TYPE_MASK
decoding, an then, the driver can handle the SPI controller of 8-bit.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add device tree support to the OMAP2+ McSPI driver.
Add the bindings documentation.

Based on original code from Rajendra.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This switches the PL022 worker to a kthread in order to get
hold of a mechanism to control the message pump priority. On
low-latency systems elevating the message kthread to realtime
priority give a real sleek response curve. This has been
confirmed by measurements. Realtime priority elevation for
a certain PL022 port can be requested from platform data.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NChris Blair <chris.blair@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The memory allocated using kzalloc by spi_alloc_master so it doesn't
need to be set to 0 again.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Conflicts:
	drivers/spi/spi-s3c64xx.c

Enable and disable the clocks to the SPI controller using runtime PM. This
serves the dual purpose of reducing power consumption a little and letting
the core know when the device is idle.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NHeiko Stuebner <heiko@sntech.de>

In preparation for the addition of runtime PM ops.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Although the hardware supports interrupts we're not currently using them
at all since for small transfers the overhead is greater than that for
busy waiting and for large transfers we have interrupts from the DMA.
This means that if the hardware reports an error (especially one which
might not stall transfer) we might miss it.

Take a first pass at dealing with such errors by enabling the interrupt
if we can and logging the errors if they happen. Ideally we'd report the
error via the affected transfer but since we're in master mode it's very
difficult to trigger errors at present and this code is much simpler.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Merge branches 'sched-urgent-for-linus', 'perf-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/accounting, proc: Fix /proc/stat interrupts sum

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tracepoints/module: Fix disabling tracepoints with taint CRAP or OOT
  x86/kprobes: Add arch/x86/tools/insn_sanity to .gitignore
  x86/kprobes: Fix typo transferred from Intel manual

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
  x86, tsc: Fix SMI induced variation in quick_pit_calibrate()
  x86, opcode: ANDN and Group 17 in x86-opcode-map.txt
  x86/kconfig: Move the ZONE_DMA entry under a menu
  x86/UV2: Add accounting for BAU strong nacks
  x86/UV2: Ack BAU interrupt earlier
  x86/UV2: Remove stale no-resources test for UV2 BAU
  x86/UV2: Work around BAU bug
  x86/UV2: Fix BAU destination timeout initialization
  x86/UV2: Fix new UV2 hardware by using native UV2 broadcast mode
  x86: Get rid of dubious one-bit signed bitfield

gpio bug fixes for v3.3

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  gpio: tps65910: Use correct offset for gpio initialization
  gpio/it8761e: Restrict it8761e gpio driver to x86.
  gpio-ml-ioh: cleanup __iomem annotation usage
  gpio-ml-ioh: cleanup NULL pointer checking
  gpio-pch: cleanup __iomem annotation usage
  gpio-pch: cleanup NULL pointer checking

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  qnx4: don't leak ->BitMap on late failure exits
  qnx4: reduce the insane nesting in qnx4_checkroot()
  qnx4: di_fname is an array, for crying out loud...
  vfs: remove printk from set_nlink()
  wake up s_wait_unfrozen when ->freeze_fs fails

In checkin

  303395ac x86: Generate system call tables and unistd_*.h from tables

the feature macros in <asm/unistd.h> were unified between 32 and 64
bits.  Unfortunately 32 bits requires __ARCH_WANT_SYS_IPC and this was
inadvertently dropped.
Reported-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/CALLzPKbeXN5gdngo8uYYU8mAow=XhrwBFBhKfG811f37BubQOg@mail.gmail.com

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: Permit key_serial() to be called with a const key pointer
  keys: fix user_defined key sparse messages
  ima: fix cred sparse warning
  MPILIB: Add a missing ENOMEM check

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

(struct qnx4_inode_entry *)(bh->b_data + some_offset)->di_fname
is not going to be NULL, TYVM...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Permit key_serial() to be called with a const key pointer.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Replace the rcu_assign_pointer() calls with rcu_assign_keypointer().
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Fix ima_policy.c sparse "warning: dereference of noderef expression"
message, by accessing cred->uid using current_cred().

Changelog v1:
- Change __cred to just cred (based on David Howell's comment)
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NJames Morris <jmorris@namei.org>