Move bus_size_bridges and assign resources out of pciehp_add_bridge()
and do them all together, one time, including slot bridge, to avoid to
calling assign resources several times when there are several bridges
under the slot bridge.  Using pci_assign_unassigned_bridge_resources.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

For use by pciehp.

pci_setup_bridge() will not check enabled for the slot bridge, otherwise
update res is not updated to bridge BAR.  That is, bridge is already
enabled for port service.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

BIOS separates IO ranges between several IOHs, and on some slots, BIOS assigns
resources to a bridge, but stops assigning resources to the device under that
bridge, because the device needs a big resource.

So:
  1. allocate resources and record the failed device resources
  2. clear the BIOS assigned resources of the parent bridge of failing device
  3. go back and call pci assign unassigned
  4. if it still fails, go up the tree, clear more bridges. and try again
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

When clearing leaf bridge resources, trying to get a big enough one, we
could shrink the bridge if there is no resource under it.  Confirm
against the old resource side to make sure we're increasing the
allocation.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This allows us to track failed allocations for later re-trying with
reallocation.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We use this in later patches to free resrouce ranges for reassignment in
an effort to support a wider variety of PCI topologies.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Reviewed-by: NAlex Chiang <achiang@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

check ioremap() return value.

Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add header file to fix build error:

drivers/pci/hotplug/ibmphp_hpc.c:135: error: implicit declaration of function 'init_MUTEX'
drivers/pci/hotplug/ibmphp_hpc.c:136: error: implicit declaration of function 'init_MUTEX_LOCKED'
drivers/pci/hotplug/ibmphp_hpc.c:797: error: implicit declaration of function 'down'
drivers/pci/hotplug/ibmphp_hpc.c:807: error: implicit declaration of function 'up'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty.  Fix this by exiting early from
pci_scan_slot if there is no device in the slot.

Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt.  ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Stanse found an ommitted pci_dev_put on one error path in
cpcihp_generic_init. The path is taken on !dev, but also when
dev->hdr_type != PCI_HEADER_TYPE_BRIDGE. However it omits to
pci_dev_put on the latter.

As it is fine to pass NULL to pci_dev_put, put it in there
uncoditionally.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Scott Murray <scott@spiteful.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The ISDN4Linux HiSax driver family contains the last remaining users
of the deprecated pci_find_device() function. This patch creates a
private copy of that function in HiSax, and removes the now unused
global function together with its controlling configuration option,
CONFIG_PCI_LEGACY.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Don't print out resources without flags to avoid cluttering up the debug
output.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Useful for freeing a portion of the resource tree, e.g. when trying to
reallocate resources more efficiently.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This is a good cleanup in itself, and makes it easier to modify specific
resource types in later code.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

ibmphp driver currently maps only 1KB of ebda memory area into kernel address
space during driver initialization. This causes kernel oops when the driver is
modprobe'd and it accesses memory beyond 1KB within ebda segment. The first
byte of ebda segment actually stores the length of the ebda region in
Kilobytes. Hence make use of the length parameter and map the entire ebda
region.
Signed-off-by: NChandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Stanse found a cut&pasted memory leak in pciehp_queue_pushbutton_work
and shpchp_queue_pushbutton_work. info is not freed/assigned on all
paths. Fix that.
Reviewed-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.

Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.

Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds the Intel Cougar Point (PCH) LPC and SMBus Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file).  This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.

To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No longer needed and causes build breakage.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add the 8.0 GT/s speed.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Take advantage of some gaps in the table to fit in support for AGP speeds.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Move the max_bus_speed and cur_bus_speed into the pci_bus.  Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array.  Use a single enum, and move it to
pci.h.  Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions.  They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all.  By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.

We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports.  These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf probe: Init struct probe_point and set counter correctly
  hw-breakpoint: Keep track of dr7 local enable bits
  hw-breakpoints: Accept breakpoints on NULL address
  perf_events: Fix FORK events

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: usbtouchscreen - extend coordinate range for Generaltouch devices
  Input: polldev can cause crash in case when polling disabled

Commit 84b79f8d (drm/i915: Fix crash
while aborting hibernation) attempted to fix a regression introduced
by commit cbda12d7 (drm/i915:
implement new pm ops for i915), but it went too far trying to split
the freeze/suspend and resume/thaw parts of the code.  As a result,
it introduced another regression, which only is visible on some systems.

Fix the problem by merging i915_drm_suspend() with
i915_drm_freeze() and moving some code from i915_resume()
into i915_drm_thaw(), so that intel_opregion_free() and
intel_opregion_init() are also executed in the freeze and thaw code
paths, respectively.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: NPedro Ribeiro <pedrib@gmail.com>
Tested-by: NTino Keitel <tino.keitel@tikei.de>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clear struct probe_point before using it in
show_perf_probe_events(), and set pp->found counter correctly in
synthesize_perf_probe_point(). Without this initialization,
clear_probe_point() will free random addresses.
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
LKML-Reference: <20100218181652.26547.57790.stgit@dhcp-100-2-132.bos.redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Generaltouch protocol allows for coordinates in [0, 0xffff] range and
there are devices reporting coordinates as high as 0x7fff so let's update
the driver to reflect that.
Signed-off-by: NRoy Yin <yhch@generaltouch.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc32: Fix struct stat uid/gid types.

Commit 085219f7
("sparc32: use proper types in struct stat")

Accidently changed the struct stat uid/gid members
to uid_t and gid_t, but those get set to
__kernel_uid32_t and __kernel_gid32_t respectively.
Those are of type 'int' but the structure is meant
to have 'short'.  So use uid16_t and gid16_t to
correct this.
Reported-by: NRob Landley <rob@landley.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] bfin: fix max timeout calculation

Relying on overflow/wrap around isn't exact because if you wrap far
enough, you get back to "valid" values.
Reported-by: NThorsten Pohlmann <pohlmann@tetronik.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

x86-32 has had a static test for copy_on_user() overflow for a while.
This test currently fails in mm/migrate.c resulting in an
allyesconfig/allmodconfig build failure on x86-32:

In function ‘copy_from_user’,
    inlined from ‘do_pages_stat’ at
    /home/hpa/kernel/git/mm/migrate.c:1012:
/home/hpa/kernel/git/arch/x86/include/asm/uaccess_32.h:212: error:
    call to ‘copy_from_user_overflow’ declared

Make the logic more explicit and therefore easier for gcc to
understand.

v2: rewrite the loop entirely using a more normal structure for a
    chunked-data loop (Linus Torvalds)
Reported-by: NLen Brown <lenb@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Reviewed-and-Tested-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Arjan van de Ven <arjan@linux.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  CacheFiles: Fix a race in cachefiles_delete_object() vs rename
  vfs: don't call ima_file_check() unconditionally in nfsd_open()
  fs: inode - remove 8 bytes of padding on 64bits allowing 1 more objects/slab under slub
  Switch proc/self to nd_set_link()
  fix LOOKUP_FOLLOW on automount "symlinks"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB: bttv: Move I2C IR initialization
  V4L/DVB: Video : pwc : Fix regression in pwc_set_shutter_speed caused by bad 	constant => sizeof conversion.
  soc-camera: mt9t112: modify exiting conditions from standby mode
  V4L/DVB: cxusb: Select all required frontend and tuner modules
  V4L/DVB: dvb: l64781.ko broken with gcc 4.5