The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages.  We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message.  This plugs some close races between the uP and
HW.  Also update the minimum required firmware version.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.

This one touches just the most simple cases:

skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()

The next ones will handle the slightly more "complex" cases.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of commit 6cdbd77e ("cxgb3 - missing CPL hanler and register
setting."), the cxgb3 ethernet NIC driver no longer handles SET_TCB
replies, so we need to do it in the iWARP driver.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Acked-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Stop the endpoint timer when the MPA exchange is aborted by the peer.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fixes for "normal close" failures:

- Start normal close timer when moving to CLOSING state.
- Handle ABORTING state in close_con_rpl().
- Stop timer correctly on abort during a normal close.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If the consumer rejects the connection we end up under-referencing the
endpoint structure.  The fix is to call iwch_ep_disconnect() instead
of the low level disconnect functions so that the endpoint close timer
is started correctly.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Stop the ep timer in ec_status() if the status indicates a
bad close.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- don't mark static functions in C files as inline - gcc should know
  best whether inlining makes sense
- never compile the unused cxio_dbg.c
- make the following needlessly global functions static:
  - cxio_hal.c: cxio_hal_clear_qp_ctx()
  - iwch_provider.c: iwch_get_qp()
- remove the following unused global functions:
  - cxio_hal.c: cxio_allocate_stag()
  - cxio_resource.: cxio_hal_get_rhdl()
  - cxio_resource.: cxio_hal_put_rhdl()
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove the Open Grid Computing copyright.  It shouldn't be there.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add an RDMA/iWARP driver for the Chelsio T3 1GbE and 10GbE adapters.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>