Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations

Pull ARM SoC fixes from Olof Johansson:
 "Here's the weekly batch of fixes from arm-soc.

  The delta is a largeish negative delta, due to revert of SMP support
  for Broadcom's STB SoC -- it was accidentally merged before some
  issues had been addressed, so they will make a new attempt for 3.18.
  I didn't see a need for a full revert of the whole platform due to
  this, we're keeping the rest enabled.

  The rest is mostly:

   - a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
   - some MTD/NAND fixes for OMAP
   - minor DT fixes for shmobile
   - warning fix for UP builds on vexpress/spc

  There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
  so it can boot.  Drivers and the rest had landed for 3.17, and it's
  small and isolated so it made sense to pick up now even if it's not a
  bugfix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  vexpress/spc: fix a build warning on array bounds
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
  MAINTAINERS: catch special Rockchip code locations
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: brcmstb: revert SMP support
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ...

With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: NAlex Shi <alex.shi@linaro.org>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:

Add basic subarchitecture support for the DRA72x and DRA74x.  These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
platforms.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/

* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: NOlof Johansson <olof@lixom.net>

Pull spi bugfixes from Mark Brown:
 "A smattering of bug fixes for the SPI subsystem, all in driver code
  which has seen active work recently and none of them with any great
  global impact.

  There's also a new ACPI ID for the pxa2xx driver which required no
  code changes and the addition of kerneldoc for some structure fields
  that were missing it and generating warnings during documentation
  builds as a result"

* tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sh-msiof: Fix transmit-only DMA transfers
  spi/rockchip: Avoid accidentally turning off the clock
  spi: dw: fix kernel crash due to NULL pointer dereference
  spi: dw-pci: fix bug when regs left uninitialized
  spi: davinci: fix SPI_NO_CS functionality
  spi/rockchip: fixup incorrect dma direction setting
  spi/pxa2xx: Add ACPI ID for Intel Braswell
  spi: spi-au1550: fix build failure
  spi: rspi: Fix leaking of unused DMA descriptors
  spi: sh-msiof: Fix leaking of unused DMA descriptors
  spi: Add missing kerneldoc bits
  spi/omap-mcspi: Fix the spi task hangs waiting dma_rx

spi: Bug fixes for v3.17

A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.

There's also a new ACPI ID for the pxa2xx driver which required no code
changes and the addition of kerneldoc for some structure fields that
were missing it and generating warnings during documentation builds as a
result.

# gpg: Signature made Sun 31 Aug 2014 13:19:12 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Fix tx/rx mixup, which broke transmit-only transfers.

Introduced by commit 4240305f7cbdc7782aa8bc40cc702775d9ac0839
("spi: sh-msiof: Fix leaking of unused DMA descriptors").
Reported-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Pull file locking bugfx from Jeff Layton:
 "Just a bugfix for a bug that crept in to v3.15.  It's in a rather rare
  error path, and I'm not aware of anyone having hit it, but it's worth
  fixing for v3.17"

* tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux:
  locks: pass correct "before" pointer to locks_unlink_lock in generic_add_lease

Merge remote-tracking branches 'spi/fix/au1550', 'spi/fix/davinci', 'spi/fix/doc', 'spi/fix/dw', 'spi/fix/omap-mcspi', 'spi/fix/pxa2xx', 'spi/fix/rockchip' and 'spi/fix/rspi' into spi-linus

Pull x86 fixes from Peter Anvin:
 "One patch to avoid assigning interrupts we don't actually have on
  non-PC platforms, and two patches that addresses bugs in the new
  IOAPIC assignment code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, irq, PCI: Keep IRQ assignment for runtime power management
  x86: irq: Fix bug in setting IOAPIC pin attributes
  x86: Fix non-PC platform kernel crash on boot due to NULL dereference

Pull ACPI and power management fixes from Rafael Wysocki:

 - Fix for an ACPI regression related to the handling of fixed events
   that caused netlink routines to be (incorrectly) run in interrupt
   context from Lan Tianyu

 - Fix for an ACPI EC driver regression on Acer Aspire V5-573G that
   caused AC/battery plug/unplug and video brightness change
   notifications to be delayed on that machine from Lv Zheng

 - Fix for an ACPI device enumeration regression that caused ACPI driver
   probe to fail for some devices where it succeeded before (Rafael J
   Wysocki)

 - intel_pstate driver fix to prevent it from printing an information
   message for every CPU in the system on every boot from Andi Kleen

 - s5pv210 cpufreq driver fix to remove an __init annotation from a
   routine that in fact can be called at any time after init too from
   Mark Brown

 - New Intel Braswell device ID for the ACPI LPSS (Low-Power Subsystem)
   driver from Alan Cox

 - New Intel Braswell CPU ID for intel_pstate from Mika Westerberg

* tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: s5pv210: Remove spurious __init annotation
  cpufreq: intel_pstate: Add CPU ID for Braswell processor
  intel_pstate: Turn per cpu printk into pr_debug
  ACPI / LPSS: Add ACPI IDs for Intel Braswell
  ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
  ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
  ACPI: Run fixed event device notifications in process context
  ACPI / scan: Allow ACPI drivers to bind to PNP device objects

Merge patches from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  kexec: purgatory: add clean-up for purgatory directory
  Documentation/kdump/kdump.txt: add ARM description
  flush_icache_range: export symbol to fix build errors
  tools: selftests: fix build issue with make kselftests target
  ocfs2: quorum: add a log for node not fenced
  ocfs2: o2net: set tcp user timeout to max value
  ocfs2: o2net: don't shutdown connection when idle timeout
  ocfs2: do not write error flag to user structure we cannot copy from/to
  x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
  drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
  xattr: fix check for simultaneous glibc header inclusion
  kexec: remove CONFIG_KEXEC dependency on crypto
  kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
  x86,mm: fix pte_special versus pte_numa
  hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
  mm/zpool: use prefixed module loading
  zram: fix incorrect stat with failed_reads
  lib: turn CONFIG_STACKTRACE into an actual option.
  mm: actually clear pmd_numa before invalidating
  memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
  ...

Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add arm specific parts to kdump kernel documentation.
Signed-off-by: NHu Keping <hukeping@huawei.com>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix building errors occuring due to a missing export of
flush_icache_range() in

kisskb.ellerman.id.au/kisskb/buildresult/11677809/

ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined!
Signed-off-by: NPranith Kumar <bobby.prani@gmail.com>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>	[arc]
Acked-by: Richard Kuo <rkuo@codeaurora.org>	[hexagon]
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>	[xtensa]
Cc: Noam Camus <noamc@ezchip.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Zhigang Lu <zlu@tilera.com>		[tile]
Cc: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the typo of ARCH when running 'make kselftests'.  Change the 'X86'
to 'x86'.  Test by compilation.
Signed-off-by: NPhong Tran <tranmanphong@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For debug use, we can see from the log whether the fence decision is
made and why it is not fenced.
Signed-off-by: NJunxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: NSrinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: NMark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When tcp retransmit timeout(15mins), the connection will be closed.
Pending messages may be lost during this time.  So we set tcp user
timeout to override the retransmit timeout to the max value.  This is OK
for ocfs2 since we have disk heartbeat, if peer crash, the disk
heartbeat will timeout and it will be evicted, if disk heartbeat not
timeout and connection idle for a long time, then this means the cluster
enters split-brain state, since fence can't happen, we'd better keep the
connection and wait network recover.
Signed-off-by: NJunxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: NSrinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: NMark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch series is to fix a possible message lost bug in ocfs2 when
network go bad.  This bug will cause ocfs2 hung forever even network
become good again.

The messages may lost in this case.  After the tcp connection is
established between two nodes, an idle timer will be set to check its
state periodically, if no messages are received during this time, idle
timer will timeout, it will shutdown the connection and try to
reconnect, so pending messages in tcp queues will be lost.  This
messages may be from dlm.  Dlm may get hung in this case.  This may
cause the whole ocfs2 cluster hung.

This is very possible to happen when network state goes bad.  Do the
reconnect is useless, it will fail if network state is still bad.  Just
waiting there for network recovering may be a good idea, it will not
lost messages and some node will be fenced until cluster goes into
split-brain state, for this case, Tcp user timeout is used to override
the tcp retransmit timeout.  It will timeout after 25 days, user should
have notice this through the provided log and fix the network, if they
don't, ocfs2 will fall back to original reconnect way.

This patch (of 3):

Some messages in the tcp queue maybe lost if we shutdown the connection
and reconnect when idle timeout.  If packets lost and reconnect success,
then the ocfs2 cluster maybe hung.

To fix this, we can leave the connection there and do the fence decision
when idle timeout, if network recover before fence dicision is made, the
connection survive without lost any messages.

This bug can be saw when network state go bad.  It may cause ocfs2 hung
forever if some packets lost.  With this fix, ocfs2 will recover from
hung if network becomes good again.
Signed-off-by: NJunxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: NSrinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: NMark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If we failed to copy from the structure, writing back the flags leaks 31
bits of kernel memory (the rest of the ir_flags field).

In any case, if we cannot copy from/to the structure, why should we
expect putting just the flags to work?

Also make sure ocfs2_info_handle_freeinode() returns the right error
code if the copy_to_user() fails.

Fixes: ddee5cdb ('Ocfs2: Add new OCFS2_IOC_INFO ioctl for ocfs2 v8.')
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: NMark Fasheh <mfasheh@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Thomas reported that build of x86_64 kernel was failing for him.  He is
using 32bit tool chain.

Problem is that while compiling purgatory, I have not specified -m64
flag.  And 32bit tool chain must be assuming -m32 by default.

Following is error message.

(mini) [~/work/linux-2.6] make
scripts/kconfig/conf --silentoldconfig Kconfig
  CHK     include/config/kernel.release
  UPD     include/config/kernel.release
  CHK     include/generated/uapi/linux/version.h
  CHK     include/generated/utsrelease.h
  UPD     include/generated/utsrelease.h
  CC      arch/x86/purgatory/purgatory.o
arch/x86/purgatory/purgatory.c:1:0: error: code model 'large' not supported in
the 32 bit mode

Fix it by explicitly passing appropriate -m64/-m32 build flag for
purgatory.
Reported-by: NThomas Glanzmann <thomas@glanzmann.de>
Tested-by: NThomas Glanzmann <thomas@glanzmann.de>
Suggested-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The rtc-s5m driver used to support devices without irq specified in the
past.  Re-add this support.

The patch fixes boot for Insignal's Exynos4412 based Origen board.

Error messages before the patch:

  ...
  Unable to handle kernel NULL pointer dereference at virtual address 00000094
  pgd = c0004000
  [00000094] *pgd=00000000
  Internal error: Oops: 5 [#1] PREEMPT SMP ARM
  Modules linked in:
  CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.16.0-next-20140804-00008-ga59480f-dirty #701
  task: ea80f000 ti: ea882000 task.ti: ea882000
  PC is at regmap_irq_get_virq+0x0/0x28
  LR is at s5m_rtc_probe+0xdc/0x310
  pc : [<c02574fc>]    lr : [<c02de75c>]    psr: 80000153
  sp : ea883e48  ip : 00000000  fp : 00000000
  r10: 0000000c  r9 : c05de7ac  r8 : eaabc600
  r7 : eaa6b4d0  r6 : c0439e8c  r5 : eaabc610  r4 : eab30e50
  r3 : 00000000  r2 : 00000000  r1 : 0000000c  r0 : 00000000
  Flags: Nzcv  IRQs on  FIQs off  Mode SVC_32  ISA ARM  Segment kernel
  Control: 10c5387d  Table: 4000404a  DAC: 00000015
  Process swapper/0 (pid: 1, stack limit = 0xea882240)
  Backtrace:
    regmap_irq_get_virq
    s5m_rtc_probe
    platform_drv_probe
    driver_probe_device
    __driver_attach
    bus_for_each_dev
    bus_add_driver
    driver_register
    do_one_initcall
    kernel_init_freeable
    kernel_init
  ---[ end trace a954d7f019122700 ]---
  Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
  ...
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The guard was introduced in commit ea1a8217 ("xattr: guard against
simultaneous glibc header inclusion") but it is using #ifdef to check
for a define that is either set to 1 or 0.  Fix it to use #if instead.

* Without this patch:

  $ { echo "#include <sys/xattr.h>"; echo "#include <linux/xattr.h>"; } | gcc -E -Iinclude/uapi - >/dev/null
  include/uapi/linux/xattr.h:19:0: warning: "XATTR_CREATE" redefined [enabled by default]
   #define XATTR_CREATE 0x1 /* set value, fail if attr already exists */
   ^
  /usr/include/x86_64-linux-gnu/sys/xattr.h:32:0: note: this is the location of the previous definition
   #define XATTR_CREATE XATTR_CREATE
   ^

* With this patch:

  $ { echo "#include <sys/xattr.h>"; echo "#include <linux/xattr.h>"; } | gcc -E -Iinclude/uapi - >/dev/null
  (no warnings)
Signed-off-by: NFilipe Brandenburger <filbranden@google.com>
Acked-by: NSerge E. Hallyn <serge.hallyn@ubuntu.com>
Cc: Allan McRae <allan@archlinux.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

New system call depends on crypto.  As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.

But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto.  Remove that dependency.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently new system call kexec_file_load() and all the associated code
compiles if CONFIG_KEXEC=y.  But new syscall also compiles purgatory
code which currently uses gcc option -mcmodel=large.  This option seems
to be available only gcc 4.4 onwards.

Hiding new functionality behind a new config option will not break
existing users of old gcc.  Those who wish to enable new functionality
will require new gcc.  Having said that, I am trying to figure out how
can I move away from using -mcmodel=large but that can take a while.

I think there are other advantages of introducing this new config
option.  As this option will be enabled only on x86_64, other arches
don't have to compile generic kexec code which will never be used.  This
new code selects CRYPTO=y and CRYPTO_SHA256=y.  And all other arches had
to do this for CONFIG_KEXEC.  Now with introduction of new config
option, we can remove crypto dependency from other arches.

Now CONFIG_KEXEC_FILE is available only on x86_64.  So whereever I had
CONFIG_X86_64 defined, I got rid of that.

For CONFIG_KEXEC_FILE, instead of doing select CRYPTO=y, I changed it to
"depends on CRYPTO=y".  This should be safer as "select" is not
recursive.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Tested-by: NShaun Ruffell <sruffell@digium.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sasha Levin has shown oopses on ffffea0003480048 and ffffea0003480008 at
mm/memory.c:1132, running Trinity on different 3.16-rc-next kernels:
where zap_pte_range() checks page->mapping to see if PageAnon(page).

Those addresses fit struct pages for pfns d2001 and d2000, and in each
dump a register or a stack slot showed d2001730 or d2000730: pte flags
0x730 are PCD ACCESSED PROTNONE SPECIAL IOMAP; and Sasha's e820 map has
a hole between cfffffff and 100000000, which would need special access.

Commit c46a7c81 ("x86: define _PAGE_NUMA by reusing software bits on
the PMD and PTE levels") has broken vm_normal_page(): a PROTNONE SPECIAL
pte no longer passes the pte_special() test, so zap_pte_range() goes on
to try to access a non-existent struct page.

Fix this by refining pte_special() (SPECIAL with PRESENT or PROTNONE) to
complement pte_numa() (SPECIAL with neither PRESENT nor PROTNONE).  A
hint that this was a problem was that c46a7c81 added pte_numa() test
to vm_normal_page(), and moved its is_zero_pfn() test from slow to fast
path: This was papering over a pte_special() snag when the zero page was
encountered during zap.  This patch reverts vm_normal_page() to how it
was before, relying on pte_special().

It still appears that this patch may be incomplete: aren't there other
places which need to be handling PROTNONE along with PRESENT?  For
example, pte_mknuma() clears _PAGE_PRESENT and sets _PAGE_NUMA, but on a
PROT_NONE area, that would make it pte_special().  This is side-stepped
by the fact that NUMA hinting faults skipped PROT_NONE VMAs and there
are no grounds where a NUMA hinting fault on a PROT_NONE VMA would be
interesting.

Fixes: c46a7c81 ("x86: define _PAGE_NUMA by reusing software bits on the PMD and PTE levels")
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Tested-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NHugh Dickins <hughd@google.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: <stable@vger.kernel.org>	[3.16]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

spin_lock may be an empty struct for !SMP configurations and so
arch_spin_is_locked may return unconditional 0 and trigger the VM_BUG_ON
even when the lock is held.

Replace spin_is_locked by lockdep_assert_held.  We will not BUG anymore
but it is questionable whether crashing makes a lot of sense in the
uncharge path.  Uncharge happens after the last page reference was
released so nobody should touch the page and the function doesn't update
any shared state except for res counter which uses synchronization of
its own.
Signed-off-by: NMichal Hocko <mhocko@suse.cz>
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

To avoid potential format string expansion via module parameters, do not
use the zpool type directly in request_module() without a format string.
Additionally, to avoid arbitrary modules being loaded via zpool API
(e.g.  via the zswap_zpool_type module parameter) add a "zpool-" prefix
to the requested module, as well as module aliases for the existing
zpool types (zbud and zsmalloc).
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: NDan Streetman <ddstreet@ieee.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since we allocate a temporary buffer in zram_bvec_read to handle partial
page operations in commit 924bd88d ("Staging: zram: allow partial
page operations"), our ->failed_reads value may be incorrect as we do
not increase its value when failing to allocate the temporary buffer.

Let's fix this issue and correct the annotation of failed_reads.
Signed-off-by: NChao Yu <chao2.yu@samsung.com>
Acked-by: NMinchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: NJerome Marchand <jmarchan@redhat.com>
Acked-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I was puzzled why /proc/$$/stack had disappeared, until I figured out I
had disabled the last debug option that did a 'select STACKTRACE'.  This
patch makes the option show up at config time, so it can be enabled
without enabling any of the more heavyweight debug options.
Signed-off-by: NDave Jones <davej@redhat.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 67f87463 ("mm: clear pmd_numa before invalidating") cleared
the NUMA bit in a copy of the PMD entry, but then wrote back the
original
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Acked-by: NMel Gorman <mgorman@suse.de>
Reviewed-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In memblock_find_in_range_node(), we defined ret as int.  But it should
be phys_addr_t because it is used to store the return value from
__memblock_find_range_bottom_up().

The bug has not been triggered because when allocating low memory near
the kernel end, the "int ret" won't turn out to be negative.  When we
started to allocate memory on other nodes, and the "int ret" could be
minus.  Then the kernel will panic.

A simple way to reproduce this: comment out the following code in
numa_init(),

        memblock_set_bottom_up(false);

and the kernel won't boot.
Reported-by: NXishi Qiu <qiuxishi@huawei.com>
Signed-off-by: NTang Chen <tangchen@cn.fujitsu.com>
Tested-by: NXishi Qiu <qiuxishi@huawei.com>
Cc: <stable@vger.kernel.org>	[3.13+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Richard and Daniel reported that UML is broken due to changes to
resource traversal functions.  Problem is that iomem_resource.child can
be null and new code does not consider that possibility.  Old code used
a for loop and that loop will not even execute if p was null.

Revert back to for() loop logic and bail out if p is null.

I also moved sibling_only check out of resource_lock. There is no
reason to keep it inside the lock.

Following is backtrace of the UML crash.

RIP: 0033:[<0000000060039b9f>]
RSP: 0000000081459da0  EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000219b3fff RCX: 000000006010d1d9
RDX: 0000000000000001 RSI: 00000000602dfb94 RDI: 0000000081459df8
RBP: 0000000081459de0 R08: 00000000601b59f4 R09: ffffffff0000ff00
R10: ffffffff0000ff00 R11: 0000000081459e88 R12: 0000000081459df8
R13: 00000000219b3fff R14: 00000000602dfb94 R15: 0000000000000000
Kernel panic - not syncing: Segfault with no mm
CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-10454-g58d08e3b #13
Stack:
 00000000 000080d0 81459df0 219b3fff
 81459e70 6010d1d9 ffffffff 6033e010
 81459e50 6003a269 81459e30 00000000
Call Trace:
 [<6010d1d9>] ? kclist_add_private+0x0/0xe7
 [<6003a269>] walk_system_ram_range+0x61/0xb7
 [<6000e859>] ? proc_kcore_init+0x0/0xf1
 [<6010d574>] kcore_update_ram+0x4c/0x168
 [<6010d72e>] ? kclist_add+0x0/0x2e
 [<6000e943>] proc_kcore_init+0xea/0xf1
 [<6000e859>] ? proc_kcore_init+0x0/0xf1
 [<6000e859>] ? proc_kcore_init+0x0/0xf1
 [<600189f0>] do_one_initcall+0x13c/0x204
 [<6004ca46>] ? parse_args+0x1df/0x2e0
 [<6004c82d>] ? parameq+0x0/0x3a
 [<601b5990>] ? strcpy+0x0/0x18
 [<60001e1a>] kernel_init_freeable+0x240/0x31e
 [<6026f1c0>] kernel_init+0x12/0x148
 [<60019fad>] new_thread_handler+0x81/0xa3

Fixes 8c86e70a ("resource: provide new functions to walk
through resources").
Reported-by: NDaniel Walter <sahne@0x90.at>
Tested-by: NRichard Weinberger <richard@nod.at>
Tested-by: NToralf Förster <toralf.foerster@gmx.de>
Tested-by: NDaniel Walter <sahne@0x90.at>
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Checkpatch currently warns if a git commit ID (in the changelog,
usually) is less than 12 characters or more than 16.  The "more than 16"
is excessive.  Change the check so we accept IDs from 12 to 40 chars in
length.

Cc: Geert Uytterhoeven <geert@linux-m68k.org
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull NFS client fixes from Trond Myklebust:
 "Highlights:
   - NFSv3 stable fix for another POSIX ACL regression
   - NFSv4 stable fix for a regression with OPEN_DOWNGRADE
   - NFSv4 stable fix for bad close() behaviour when holding a delegation"

* tag 'nfs-for-3.17-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv3: Fix another acl regression
  NFSv4: Don't clear the open state when we just did an OPEN_DOWNGRADE
  NFSv4: Fix problems with close in the presence of a delegation

Pull USB fixes from Greg KH:
 "Here are a bunch of fixes for the USB drivers for 3.17-rc3.

  Also in here is the movement of the usbip driver out of staging, into
  the "real" part of the kernel, it had to wait until after -rc1 to
  handle the merge issues involved between the USB and staging trees.
  The code is identical, just file movements there.

  The USB fixes are all over the place, new device ids, xhci fixes for
  reported issues and the usual gadget driver fixes as well.  All have
  been in linux-next for a while now"

* tag 'usb-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (46 commits)
  USB: fix build error with CONFIG_PM_RUNTIME disabled
  Revert "usb: ehci/ohci-exynos: Fix PHY getting sequence"
  xhci: Disable streams on Via XHCI with device-id 0x3432
  USB: serial: fix potential heap buffer overflow
  USB: serial: fix potential stack buffer overflow
  usb: ehci/ohci-exynos: Fix PHY getting sequence
  usb: hub: Prevent hub autosuspend if usbcore.autosuspend is -1
  USB: sisusb: add device id for Magic Control USB video
  usb: dwc2: gadget: Set the default EP max packet value as 8 bytes
  usb: ehci: using wIndex + 1 for hub port
  USB: storage: add quirk for Newer Technology uSCSI SCSI-USB converter
  MAINTAINERS: Add an entry for USB/IP driver
  usbip: remove struct usb_device_id table
  usbip: move usbip kernel code out of staging
  usbip: move usbip userspace code out of staging
  USB: whiteheat: Added bounds checking for bulk command response
  usb: gadget: remove $(PWD) in ccflags-y
  usb: pch_udc: usb gadget device support for Intel Quark X1000
  usb: gadget: uvc: fix possible lockup in uvc gadget
  usb: wusbcore: fix below build warning
  ...

Pull staging driver fixes from Greg KH:
 "Here are some staging driver fixes for your tree.  Nothing huge, just
  some fixes for issues that have been reported and a few new device ids
  added.

  All have been in linux-next for a while"

* tag 'staging-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Add new USB ID
  staging/rtl8188eu: add 0df6:0076 Sitecom Europe B.V.
  staging: android: fix a possible memory leak
  staging: lustre: lustre: libcfs: workitem.c: Cleaning up missing null-terminate after strncpy call
  staging: et131x: Fix errors caused by phydev->addr accesses before initialisation
  staging: lustre: Remove circular dependency on header

Pull char/misc driver fixes from Greg KH:
 "Here are 3 fixes for the mei and thunderbolt drivers that resolve some
  reported issues.

  All have been in linux-next for a while"

* tag 'char-misc-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  thunderbolt: Clear hops before overwriting
  mei: nfc: fix memory leak in error path
  mei: reset client state on queued connect request