This fixes below build warnings:
  CC      drivers/mfd/adp5520.o
drivers/mfd/adp5520.c:324:12: warning: 'adp5520_suspend' defined but not used [-Wunused-function]
drivers/mfd/adp5520.c:333:12: warning: 'adp5520_resume' defined but not used [-Wunused-function]
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch fixes conflict between commit 8ae3559
"mfd: mc13xxx workaround SPI hardware bug on i.Mx"
and commit 10c7a5d "mfd: Use devm_* APIs for mc13xxx".

commit 8ae3559 changes regmap_init_spi to regmap_init.
So now we need to use devm_regmap_init rather than devm_regmap_init_spi.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.

This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.

This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.

The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.

I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.

v3 - Brown paper bag its too early in the morning actually run
     git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: NMantesh Sarashetti <mantesh@ti.com>
Tested-by: NMantesh Sarashetti <mantesh@ti.com>
Acked-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Tested-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: NRuss Dill <Russ.Dill@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Allocate memory and irq for device state using devm_*
helpers to simplify memory accounting.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Ensure that we leave the device with the pins in the expected
configuration if we leave it in reset over suspend, avoiding any
interoperation problems with other devices in the system.
Signed-off-by: NChris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

twl6040 needs CONFIG_IRQ_DOMAIN to compile, without this we have:
drivers/mfd/twl6040-irq.c: In function 'twl6040_irq_init':
drivers/mfd/twl6040-irq.c:164:2: error: implicit declaration of function 'irq_domain_add_legacy'
drivers/mfd/twl6040-irq.c:165:11: error: 'irq_domain_simple_ops' undeclared (first use in this function)
drivers/mfd/twl6040-irq.c:165:11: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We need to call max77693_irq_exit() in max77693_i2c_probe error patch and
max77693_i2c_remove.

Current code already uses devm_kzalloc() to allocate memory for max77693.
Thus we should not call kfree(max77693), otherwise we got double free.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Commit 72fb9220 ("mfd/ab5500: delete
AB5500 support") deleted all files that used ab5500-core.h. That file
apparently was simply overlooked. Delete it too.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

They're not referenced outside this file.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

MAX8925 rtc irq is transfered from mfd resources now.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fixes the following sparse warnings:
drivers/mfd/max8997.c:209:4: warning: symbol 'max8997_dumpaddr_pmic' was not declared. Should it be static?
drivers/mfd/max8997.c:334:4: warning: symbol 'max8997_dumpaddr_muic' was not declared. Should it be static?
drivers/mfd/max8997.c:344:4: warning: symbol 'max8997_dumpaddr_haptic' was not declared. Should it be static?
drivers/mfd/max8997.c:426:25: warning: symbol 'max8997_pm' was not declared. Should it be static?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Instead of just printing the register value, also output some
description of the value.
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: NMattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Force the Modem wakeup by asserting the CaWakeReq signal before the
hostaccess_req/ack ping-pong sequence. The Awake_req signal is de-asserted
asserted at the same time than the hostaccess_req. Return error on failure
case so that the client using this can take appropiate steps.
Signed-off-by: NArun Murthy <arun.murthy@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since none of the users now reference the cache directly we can happily
remove the custom cache code and rely on the regmap cache.

For simplicity we don't bother with the register defaults tables but
instead read the defaults from the device - regmap is capable of doing
this, unlike our old cache infrastructure. This saves a lot of code and
allows us to cache the device revision information too.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

We can just use regmap_update_bits() to achieve the same effect - it will
do the read/modify/update cycle for us.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the most simple possible transformation on the existing code so keep
the table sitting around, further patches in this series will delete the
existing cache code - the main purpose of this patch is to ensure that
we always have a cache for bisection.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NChris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Hierarchically, the AB8500 is a child of the DB8500 PRCMU. So now that
Device Tree is being used and MFD core code is Device Tree aware, we
can simply register DB8500 PRCMU from Device Tree in the normal way
then allow the DB8500 PRCMU driver to register the AB8500 as a simple
MFD device at probe time.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The AB8500 is soon to have its own IRQ domain. For this to be useful
the driver needs to be initialised earlier in the boot sequence. Here
we move initialisation forward from arch_initcall to core_initcall time.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Now the AB8500 has its own IRQ domain it needs to be initialised earlier
in the boot sequence. As the AB8500 relies on the DB8500 PRCMU we need to
reflect this change for the PRCMU driver too.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

During Device Tree enablement of the ab8500 and db8500-prcmu drivers,
a decision was made to omit registration through the MFD API and use
Device Tree directly. However, because MFD devices have a different
address space and the ab8500 and db8500 both use I2C to communicate,
this causes issues with address translation during execution of
of_platform_populate(). So the solution is to make the MFD core aware
of Device Tree and have it assign the correct node pointers instead.

To make this work the MFD core also needs to be awere of IRQ domains,
as Device Tree insists on IRQ domain compatibility. So, instead of
providing an irq-base via platform code, in the DT case we simply
look up the IRQ domain and map to the correct virtual IRQ.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

There is only one method used to communicate with the DB8500 PRCMU, via I2C.
Now this can be assumed, there is no requirement to specify the protocol in
the function name. This patch removes protocol specifics and uses a more
generic naming convention.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

As the AB8500 is an IRQ controller in its own right, here we provide
the AB8500 driver with IRQ domain support. This is required if we wish
to reference any of its IRQs from a platform's Device Tree.

Cc: Naga Radheshy <naga.radheshy@stericsson.com>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds the correct compatible string for use during Device Tree
population. Without it the DB8500 PRCMU will not be probed.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

During ab8500-core clean-up the Kconfig entry for AB8500_I2C_CORE
was left remnant. This patch simply removes it.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The kernel now forces IRQs to be ONESHOT if no IRQ handler is passed.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The MC13xxx PMIC is mainly used on i.Mx SoC. On those SoC the SPI
hardware will deassert CS line as soon as the SPI FIFO is empty.
The MC13xxx hardware is very sensitive to CS line change as it
corrupts the transfer if CS is deasserted in the middle of a register
read or write.
It is not possible to use the CS line as a GPIO on some SoC, so we
need to workaround this by implementing a single SPI transfer to
access the PMIC.
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMarc Reilly <marc@cpdesign.com.au>
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This fix the SPI regmap configuration, the wrong write flag was used.
Also, bits_per_word should not be set as the regmap spi implementation
uses a 8bits transfert granularity.
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Now this driver is using regmap APIs, the iolock mutex is not used and can be
removed.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is to address the following warning during compilation time:

  drivers/mfd/da9052-core.c: In function ‘da9052_device_init’:
  drivers/mfd/da9052-core.c:646: warning: unused variable ‘desc’

This variable is indeed no longer in use (change can be traced back
to commit: 86144194).
Signed-off-by: NKrzysztof Wilczynski <krzysztof.wilczynski@linux.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch is device driver for MAX77686 chip.
MAX77686 is PMIC and includes regulator and rtc on it.
This driver is core of MAX77686 chip, so provides common support for
accessing on-chip devices. It uses irq_domain to manage irq and regmap
to read/write data to its register with i2c bus.
Signed-off-by: NChiwoong Byun <woong.byun@samsung.com>
Signed-off-by: NJonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Pull security docs update from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: Minor improvements to no_new_privs documentation

We already use them for openat() and friends, but fchdir() also wants to
be able to use O_PATH file descriptors.  This should make it comparable
to the O_SEARCH of Solaris.  In particular, O_PATH allows you to access
(not-quite-open) a directory you don't have read persmission to, only
execute permission.

Noticed during development of multithread support for ksh93.
Reported-by: Nольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org    # O_PATH introduced in 3.0+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Last merge window, we had some updates from Al cleaning up the signal
  restart handling.  These have caused some problems on ARM, and while
  Al has some fixes, we have some concerns with Al's patches but we've
  been unsuccesful with discussing this.

  We have got to the point where we need to do something, and we've
  decided that the best solution is to revert the appropriate commits
  until Al is able to reply to us.

  Also included here are four patches to fix warnings that I've noticed
  in my build system, and one fix for kprobes test code."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: fix warning caused by wrongly typed arm_dma_limit
  ARM: fix warnings about atomic64_read
  ARM: 7440/1: kprobes: only test 'sub pc, pc, #1b-2b+8-2' on ARMv6
  ARM: 7441/1: perf: return -EOPNOTSUPP if requested mode exclusion is unavailable
  ARM: 7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK"
  ARM: 7442/1: Revert "remove unused restart trampoline"
  ARM: fix set_domain() macro
  ARM: fix mach-versatile/pci.c warning

The documentation didn't actually mention how to enable no_new_privs.
This also adds a note about possible interactions between
no_new_privs and LSMs (i.e. why teaching systemd to set no_new_privs
is not necessarily a good idea), and it references the new docs
from include/linux/prctl.h.
Suggested-by: NRob Landley <rob@landley.net>
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NJames Morris <james.l.morris@oracle.com>

Merge tag 'ecryptfs-3.5-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Fixes an incorrect access mode check when preparing to open a file in
  the lower filesystem.  This isn't an urgent fix, but it is simple and
  the check was obviously incorrect.

  Also fixes a couple important bugs in the eCryptfs miscdev interface.
  These changes are low risk due to the small number of users that use
  the miscdev interface.  I was able to keep the changes minimal and I
  have some cleaner, more complete changes queued up for the next merge
  window that will build on these patches."

* tag 'ecryptfs-3.5-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Gracefully refuse miscdev file ops on inherited/passed files
  eCryptfs: Fix lockdep warning in miscdev operations
  eCryptfs: Properly check for O_RDONLY flag before doing privileged open