Now that libata uses sd->manage_start_stop, libata spins down disk on
shutdown.  In an attempt to compensate libata's previous shortcoming,
some distros sync and spin down disks attached via libata in their
shutdown(8).  Some disks spin back up just to spin down again on
STANDBYNOW1 if the command is issued when the disk is spun down, so
this double spinning down causes problem.

This patch implements module parameter libata.spindown_compat which,
when set to one (default value), prevents libata from spinning down
disks on shutdown thus avoiding double spinning down.  Note that
libata spins down disks for suspend to mem and disk, so with
libata.spindown_compat set to one, disks should be properly spun down
in all cases without modifying shutdown(8).

shutdown(8) should be fixed eventually.  Some drive do spin up on
SYNCHRONZE_CACHE even when their cache is clean.  Those disks
currently spin up briefly when sd tries to shutdown the device and
then the machine powers off immediately, which can't be good for the
head.  We can't skip SYNCHRONIZE_CACHE during shudown as it can be
dangerous data integrity-wise.

So, this spindown_compat parameter is already scheduled for removal by
the end of the next year and here's what shutdown(8) should do.

  * Check whether /sys/modules/libata/parameters/spindown_compat
    exists.  If it does, write 0 to it.

  * For each libata harddisk {
	* Check whether /sys/class/scsi_disk/h:c:i:l/manage_start_stop
	  exists.  Iff it doesn't, synchronize cache and spin the disk
	  down as before.
  }

The above procedure will make shutdown(8) work properly with kernels
before this change, ones with this workaround and later ones without
it.

To accelerate shutdown(8) updates, if the compat mode is in use, this
patch prints BIG FAT warning for five seconds during shutdown (the
optimal interval to annoy the user just the right amount discovered by
hours of tireless usability testing).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reimplement suspend/resume support using sdev->manage_start_stop.

* Device suspend/resume is now SCSI layer's responsibility and the
  code is simplified a lot.

* DPM is dropped.  This also simplifies code a lot.  Suspend/resume
  status is port-wide now.

* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.

* Resume now has to wait for disk to spin up before proceeding.  I
  couldn't find easy way out as libata is in EH waiting for the
  disk to be ready and sd is waiting for EH to complete to issue
  START_STOP.

* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
  This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (122 commits)
  [ALSA] version 1.0.14rc4
  [ALSA] Add speaker pin sequencing to hda_codec.c:snd_hda_parse_pin_def_config()
  [ALSA] hda-codec - Add ALC861VD Lenovo support
  [ALSA] hda-codec - Fix connection list in generic parser
  [ALSA] usb-audio: work around wrong wMaxPacketSize on ESI M4U
  [ALSA] usb-audio: work around broken M-Audio MidiSport Uno firmware
  [ALSA] usb-audio: explicitly match Logitech QuickCam
  [ALSA] hda-codec - Fix a typo
  [ALSA] hda-codec - Fix ALC880 uniwill auto-mutes
  [ALSA] hda-codec - Fix AD1988 SPDIF playback route control
  [ALSA] wm8750 typo fix
  [ALSA] wavefront: only declare isapnp on CONFIG_PNP
  [ALSA] hda-codec - bug fixes for stac92xx HDA codecs.
  [ALSA] add MODULE_FIRMWARE entries
  [ALSA] do not depend on FW_LOADER when internal firmware images are used
  [ALSA] hda-codec - Fix resume of STAC92xx codecs
  [ALSA] usbaudio - Revert the minimal period size fix patch
  [ALSA] hda-codec - Add support for new HP DV series laptops
  [ALSA] usb-audio - Fix the minimum period size per transfer mode
  [ALSA] sound/pcmcia/vx/vxpocket.c: fix an if() condition
  ...

* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (44 commits)
  V4L/DVB (5571): V4l1-compat:  Make VIDIOCSPICT return errors in a useful way
  V4L/DVB (5624): Radio-maestro.c cleanup
  V4L/DVB (5623): Dsbr100.c Replace usb_dsbr100_do_ioctl to use video_ioctl2
  V4L/DVB (5622): Radio-zoltrix.c cleanup
  V4L/DVB (5621): Radio-cadet.c Replace cadet_do_ioctl to use video_ioctl2
  V4L/DVB (5619): Dvb-usb: fix typo
  V4L/DVB (5618): Cx88: Drop the generic i2c client from cx88-vp3054-i2c
  V4L/DVB (5617): V4L2: videodev, allow debugging
  V4L/DVB (5614): M920x: Disable second adapter on LifeView TV Walker Twin
  V4L/DVB (5613): M920x: loosen up 80-col limit
  V4L/DVB (5612): M920x: rename function prefixes from m9206_foo to m920x_foo
  V4L/DVB (5611): M920x: replace deb_rc with deb
  V4L/DVB (5610): M920x: remove duplicated code
  V4L/DVB (5609): M920x: group like functions together
  V4L/DVB (5608): M920x: various whitespace cleanups
  V4L/DVB (5607): M920x: Initial support for devices likely manufactured by Dposh
  V4L/DVB (5606): M920x: add "c-basic-offset: 8" to help emacs to enforce tabbing
  V4L/DVB (5605): M920x: Add support for LifeView TV Walker Twin
  V4L/DVB (5603): V4L: Prevent queueing queued buffers.
  V4L/DVB (5602): Enable DiSEqC in Starbox II (vp7021a)
  ...

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Quicklist support for IA64
  [IA64] fix Kprobes reentrancy
  [IA64] SN: validate smp_affinity mask on intr redirect
  [IA64] drivers/char/snsc_event.c:206: warning: unused variable `p'
  [IA64] mca.c:121: warning: 'cpe_poll_timer' defined but not used
  [IA64] Fix - Section mismatch: reference to .init.data:mvec_name
  [IA64] more warning cleanups
  [IA64] Wire up epoll_pwait and utimensat
  [IA64] Fix warnings resulting from type-checking in dev_dbg()
  [IA64] typo s/kenrel/kernel/

The code was ok, but triggered warnings for calling __init from
__cpuinit. Instead call it from check_bugs instead.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I'm using a custom BIOS to configure the northbridge GART at address
0x80000000, size 2G.  Linux complains:

"Aperture from northbridge cpu 0 beyond 4GB. Ignoring."

I think there's an off-by-two error in arch/x86_64/kernel/aperture.c:

AK: use correct types for i386
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
  further UTF-8 fixes and name correction
  Fix wrong identifier name in Documentation/kref.txt

> -** Copyright 1994 by Bj<94>rn Brauel
> +** Copyright 1994 by Bj”rn Brauel

I think these were cp437, and it should read 'Björn'.
(asm-m68k/atari*.h)

Also note that Arnaldo just put more legacy noise into CREDITS...
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

There's a typo / wrong identifier name in Documentation/kref.txt. Fix it.
Signed-off-by: NSatyam Sharma <ssatyam@cse.iitk.ac.in>
Acked-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-ip22:
  Convert SGI IP22 and specific drivers to platform_device.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (28 commits)
  [MIPS] Rework cobalt_board_id
  [MIPS] Use RTC_CMOS for Cobalt
  [MIPS] Use platform_device for Cobalt UART
  [MIPS] Separate Alchemy processor based boards config
  [MIPS] Fix build error in atomic64_cmpxchg
  [MIPS] Run checksyscalls for N32 and O32 ABI
  [MIPS] tlbex: use __maybe_unused
  [MIPS] excite: use __maybe_unused
  [MIPS] Add extern cobalt_board_id
  [MIPS] Remove unused CONFIG_TOSHIBA_BOARDS
  [MIPS] Rename tb0229_defconfig to tb0219_defconfig
  [MIPS] Update tb0229_defconfig; add CONFIG_GPIO_TB0219.
  [MIPS] Add minimum defconfig for RBHMA4200
  [MIPS] SB1: Build fix.
  [MIPS] Drop __devinit tag from allocate_irqno() and free_irqno()
  [MIPS] clocksource: use CLOCKSOURCE_MASK() macro
  [MIPS] Remove LIMITED_DMA support
  [MIPS] Remove Momenco Jaguar ATX support
  [MIPS] Remove Momenco Ocelot G support
  [MIPS] FPU hazard handling
  ...

* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
  Fix compile/link of init/do_mounts.c with !CONFIG_BLOCK
  When stacked block devices are in-use (e.g. md or dm), the recursive calls

* 'audit.b38' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] Abnormal End of Processes
  [PATCH] match audit name data
  [PATCH] complete message queue auditing
  [PATCH] audit inode for all xattr syscalls
  [PATCH] initialize name osid
  [PATCH] audit signal recipients
  [PATCH] add SIGNAL syscall class (v3)
  [PATCH] auditing ptrace

* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
  USB HID: hiddev - fix race between hiddev_send_event() and hiddev_release()
  HID: add hooks for getkeycode() and setkeycode() methods
  HID: switch to using input_dev->dev.parent
  USB HID: Logitech wheel 0x046d/0xc294 needs HID_QUIRK_NOGET quirk
  USB HID: usb_buffer_free() cleanup
  USB HID: report descriptor of Cypress USB barcode readers needs fixup
  Bluetooth HID: HIDP - don't initialize force feedback
  USB HID: update CONFIG_USB_HIDINPUT_POWERBOOK description
  HID: add input mappings for non-working keys on Logitech S510 remote

IA64 is the origin of the quicklist implementation.  So cut out the pieces
that are now in core code and modify the functions called.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

In case of reentrance i.e when a probe handler calls a functions which
inturn has a probe, we save a previous kprobe information and just single
step the reentrant probe without calling the actual probe handler.  During
this reentracy period, if an interrupt occurs and if probe happens to
trigger in the inturrupt path, then we were corrupting the previous kprobe(
as we were overriding the previous kprobe info) info their by crashing the
system.  This patch fixes this issues by having a an array of previous
kprobe info struct(with the array size of 2).

This similar technique is not needed on i386 and x86_64 because by default
interrupts are turn off in the break/int3 exception handler.
Signed-off-by: NAnil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

On SN, only allow one bit to be set in the smp_affinty mask when
redirecting an interrupt.  Currently setting multiple bits is allowed, but
only the first bit is used in determining the CPU to redirect to.  This has
caused confusion among some customers.

[akpm@linux-foundation.org: fixes]
Signed-off-by: NJohn Keller <jpk@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NTony Luck <tony.luck@intel.com>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
  [NETFILTER]: xt_conntrack: add compat support
  [NETFILTER]: iptable_raw: ignore short packets sent by SOCK_RAW sockets
  [NETFILTER]: iptable_{filter,mangle}: more descriptive "happy cracking" message
  [NETFILTER]: nf_nat: Clears helper private area when NATing
  [NETFILTER]: ctnetlink: clear helper area and handle unchanged helper
  [NETFILTER]: nf_conntrack: Removes unused destroy operation of l3proto
  [NETFILTER]: nf_conntrack: Removes duplicated declarations
  [NETFILTER]: nf_nat: remove unused argument of function allocating binding
  [NETFILTER]: Clean up table initialization
  [NET_SCHED]: Avoid requeue warning on dev_deactivate
  [NET_SCHED]: Reread dev->qdisc for NETDEV_TX_OK
  [NET_SCHED]: Rationalise return value of qdisc_restart
  [NET]: Fix dev->qdisc race for NETDEV_TX_LOCKED case
  [UDP]: Fix AF-specific references in AF-agnostic code.
  [IrDA]: KingSun/DonShine USB IrDA dongle support.
  [IPV6] ROUTE: Assign rt6i_idev for ip6_{prohibit,blk_hole}_entry.
  [IPV6]: Do no rely on skb->dst before it is assigned.
  [IPV6]: Send ICMPv6 error on scope violations.
  [SCTP]: Do not include ABORT chunk header in the notification.
  [SCTP]: Correctly copy addresses in sctp_copy_laddrs
  ...

When exporting input device bitmaps via compat_ioctl on BIG_ENDIAN
platforms evdev calculates data size incorrectly. This causes buffer
overflow if user specifies buffer smaller than maxlen.
Signed-off-by: NKenichi Nagai <kenichi3.nagai@toshiba.co.jp>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

During a 'resync' or similar activity, md checks if the devices in the
array are otherwise active and winds back resync activity when they are.
This test in done in is_mddev_idle, and it is somewhat fragile - it
sometimes thinks there is non-sync io when there isn't.

The test compares the total sectors of io (disk_stat_read) with the sectors
of resync io (disk->sync_io).  This has problems because total sectors gets
updated when a request completes, while resync io gets updated when the
request is submitted.  The time difference can cause large differenced
between the two which do not actually imply non-resync activity.  The test
currently allows for some fuzz (+/- 4096) but there are some cases when it
is not enough.

The test currently looks for any (non-fuzz) difference, either positive or
negative.  This clearly is not needed.  Any non-sync activity will cause
the total sectors to grow faster than the sync_io count (never slower) so
we only need to look for a positive differences.

If we do this then the amount of in-flight sync io will never cause the
appearance of non-sync IO.  Once enough non-sync IO to worry about starts
happening, resync will be slowed down and the measurements will thus be
more precise (as there is less in-flight) and control of resync will still
be suitably responsive.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the obsolete "if [ ]" construct from the video console Kconfig
file.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Acked-by: NJames Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert internal wait_pm2() function to fb API fb_sync() method.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Let the user enable debugging messages in nvidiafb.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix rivafb's I2C getscl callback function, as was done in nvidiafb recently.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adds a framebuffer driver to ATMEL AT91SAM9x and AT32 aka AVR32 platforms.
Those chips share quite the same IP and this code is suitable for both
architectures.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a basic port from 2.4 kernel to 2.6.  Acceleration is lost and big
endian support probably too.  The driver works in 8, 16 and 32 bit mode.

[adaplas]
- change VESA_* to FB_BLANK_* constants
- removed unused function clear_memory
- fix uninitialized variable compiler warning
- some whitespace cleaning

[akpm@linux-foundation.org: Nuke pestiferous CVS string]
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ups... coding style.
Signed-off-by: NMichal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Re-arrange epoll code to avoid static functions pre-declarations, and apply
akpm-filter on it.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Epoll is either compiled it, or not (if EMBEDDED). Remove the module code
and use fs_initcall().
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cut out lots of code from epoll, by reusing the anonymous inode source
patch (fs/anon_inodes.c).
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is an example about how to add eventfd support to the current KAIO code,
in order to enable KAIO to post readiness events to a pollable fd (hence
compatible with POSIX select/poll).  The KAIO code simply signals the eventfd
fd when events are ready, and this triggers a POLLIN in the fd.  This patch
uses a reserved for future use member of the struct iocb to pass an eventfd
file descriptor, that KAIO will use to post events every time a request
completes.  At that point, an aio_getevents() will return the completed result
to a struct io_event.  I made a quick test program to verify the patch, and it
runs fine here:

http://www.xmailserver.org/eventfd-aio-test.c

The test program uses poll(2), but it'd, of course, work with select and epoll
too.

This can allow to schedule both block I/O and other poll-able devices
requests, and wait for results using select/poll/epoll.  In a typical
scenario, an application would submit KAIO request using aio_submit(), and
will also use epoll_ctl() on the whole other class of devices (that with the
addition of signals, timers and user events, now it's pretty much complete),
and then would:

	epoll_wait(...);
	for_each_event {
		if (curr_event_is_kaiofd) {
			aio_getevents();
			dispatch_aio_events();
		} else {
			dispatch_epoll_event();
		}
	}
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch wires the eventfd system call to the x86 architectures.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a very simple and light file descriptor, that can be used as event
wait/dispatch by userspace (both wait and dispatch) and by the kernel
(dispatch only).  It can be used instead of pipe(2) in all cases where those
would simply be used to signal events.  Their kernel overhead is much lower
than pipes, and they do not consume two fds.  When used in the kernel, it can
offer an fd-bridge to enable, for example, functionalities like KAIO or
syslets/threadlets to signal to an fd the completion of certain operations.
But more in general, an eventfd can be used by the kernel to signal readiness,
in a POSIX poll/select way, of interfaces that would otherwise be incompatible
with it.  The API is:

int eventfd(unsigned int count);

The eventfd API accepts an initial "count" parameter, and returns an eventfd
fd.  It supports poll(2) (POLLIN, POLLOUT, POLLERR), read(2) and write(2).

The POLLIN flag is raised when the internal counter is greater than zero.

The POLLOUT flag is raised when at least a value of "1" can be written to the
internal counter.

The POLLERR flag is raised when an overflow in the counter value is detected.

The write(2) operation can never overflow the counter, since it blocks (unless
O_NONBLOCK is set, in which case -EAGAIN is returned).

But the eventfd_signal() function can do it, since it's supposed to not sleep
during its operation.

The read(2) function reads the __u64 counter value, and reset the internal
value to zero.  If the value read is equal to (__u64) -1, an overflow happened
on the internal counter (due to 2^64 eventfd_signal() posts that has never
been retired - unlickely, but possible).

The write(2) call writes an __u64 count value, and adds it to the current
counter.  The eventfd fd supports O_NONBLOCK also.

On the kernel side, we have:

struct file *eventfd_fget(int fd);
int eventfd_signal(struct file *file, unsigned int n);

The eventfd_fget() should be called to get a struct file* from an eventfd fd
(this is an fget() + check of f_op being an eventfd fops pointer).

The kernel can then call eventfd_signal() every time it wants to post an event
to userspace.  The eventfd_signal() function can be called from any context.
An eventfd() simple test and bench is available here:

http://www.xmailserver.org/eventfd-bench.c

This is the eventfd-based version of pipetest-4 (pipe(2) based):

http://www.xmailserver.org/pipetest-4.c

Not that performance matters much in the eventfd case, but eventfd-bench
shows almost as double as performance than pipetest-4.

[akpm@linux-foundation.org: fix i386 build]
[akpm@linux-foundation.org: add sys_eventfd to sys_ni.c]
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch implements the necessary compat code for the timerfd system call.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch wires the timerfd system call to the x86 architectures.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch introduces a new system call for timers events delivered though
file descriptors.  This allows timer event to be used with standard POSIX
poll(2), select(2) and read(2).  As a consequence of supporting the Linux
f_op->poll subsystem, they can be used with epoll(2) too.

The system call is defined as:

int timerfd(int ufd, int clockid, int flags, const struct itimerspec *utmr);

The "ufd" parameter allows for re-use (re-programming) of an existing timerfd
w/out going through the close/open cycle (same as signalfd).  If "ufd" is -1,
s new file descriptor will be created, otherwise the existing "ufd" will be
re-programmed.

The "clockid" parameter is either CLOCK_MONOTONIC or CLOCK_REALTIME.  The time
specified in the "utmr->it_value" parameter is the expiry time for the timer.

If the TFD_TIMER_ABSTIME flag is set in "flags", this is an absolute time,
otherwise it's a relative time.

If the time specified in the "utmr->it_interval" is not zero (.tv_sec == 0,
tv_nsec == 0), this is the period at which the following ticks should be
generated.

The "utmr->it_interval" should be set to zero if only one tick is requested.
Setting the "utmr->it_value" to zero will disable the timer, or will create a
timerfd without the timer enabled.

The function returns the new (or same, in case "ufd" is a valid timerfd
descriptor) file, or -1 in case of error.

As stated before, the timerfd file descriptor supports poll(2), select(2) and
epoll(2).  When a timer event happened on the timerfd, a POLLIN mask will be
returned.

The read(2) call can be used, and it will return a u32 variable holding the
number of "ticks" that happened on the interface since the last call to
read(2).  The read(2) call supportes the O_NONBLOCK flag too, and EAGAIN will
be returned if no ticks happened.

A quick test program, shows timerfd working correctly on my amd64 box:

http://www.xmailserver.org/timerfd-test.c

[akpm@linux-foundation.org: add sys_timerfd to sys_ni.c]
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch implements the necessary compat code for the signalfd system call.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>