changed is not initialized in path_power_down_sync, but it is expected
to be false in case no change happened in the loop. So set it to
false.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The generic parser should evaluate the availability of the independent
HP when specified.  Otherwise a DAC without the direct connection to
the corresponding pin may be assigned for the HP, but the driver
doesn't check it at all.  The problem was actually seen on some
machines with VT1708s or equivalent codec, where DAC0 is assigned to
HP although it can be connected only via aamix.

This patch adds the badness evaluation for the independent HP to make
it working properly.
Reported-by: NLydia Wang <LydiaWang@viatech.com.cn>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The current badness value used for the missing multi-io seems too
weak, and the multi-io tends to be skipped for desktop configurations
when no enough DACs are available.  It's because the total badness of
the multi-io becomes often larger than the badness with assigning an
individual DAC to a headphone jack.  This is good for one side, but it
seems that the surround outputs are more demanded by that.

This patch increases the badness value for the missing multi-io
slightly so that the multi-io would be preferred than the individual
headphone DAC if they conflict.  Through the tests with hda-emu,
mostly only desktop configurations with ALC662/663 and CMI codecs are
affected by this change, and all look reasonable.
Reported-by: NRaymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The loopback list is referred by the VIA codec driver no matter
whether CONFIG_PM is set or not, thus we need to enable it always.
Otherwise it gets compile errors.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Because currently snd_printd() and snd_printdd() macros are expanded
to empty when CONFIG_SND_DEBUG=n, a compile warning like below
appears sometimes, and we had to covert it by ugly ifdefs:
  sound/pci/hda/patch_sigmatel.c: In function ‘stac92hd71bxx_fixup_hp’:
  sound/pci/hda/patch_sigmatel.c:2434:24: warning: unused variable ‘spec’ [-Wunused-variable]

For "fixing" these issues better, this patch replaces snd_printd() and
snd_printdd() definitions with empty inline functions instead of
macros.  This should have the same effect but shut up warnings like
above.

But since we had already put ifdefs, changing to inline functions
would trigger compile errors.  So, such ifdefs is removed in this
patch.

In addition, snd_pci_quirk name field is defined only when
CONFIG_SND_DEBUG_VERBOSE is set, and the reference to it in
snd_printdd() argument triggers the build errors, too.  For avoiding
these errors, introduce a new macro snd_pci_quirk_name() that is
defined no matter how the debug option is set.
Reported-by: NStratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a better power filter hook for powering down unused
widgets in the generic parser.

The feature is enabled by setting hda_gen_spec.power_down_unused
flag.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The arguments to call is_active_nid() in activate_amp() were swapped,
and this resulted in the muted amp on some SPDIF output pins.

Also, the index to be passed to is_active_nid() must be idx_to_check.
Otherwise it checks the wrong connection in the case of implicit aamix
connection paths.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Introduce a helper function to do the same thing.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AD1988 family and AD1882 codecs have another mixer widget (0x21)
between the analog-loopback mixer widget (0x20) and the actual
outputs.  Due to this hole, the analog-loopbacks aren't sent properly
to the output pins.

As a band-aid fix, introduce another fields holding the aamix merge
path, and activate it.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() are called usually at the same time,
we can simply combine them to a single function,
snd_hda_codec_flush_cache().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The capture volume put callback may call the node selection change,
and its actual call won't be triggered unless flushed.  In general,
we always need to call both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() at the same place...
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Both the HP auto-mute and the independent HP mode conflict with each
other.  Make HP auto-mute disabled (only for the affected HP jack)
during the driver is in HP independent mode.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It'd be better to give another name to the secondary (alt) analog PCM
stream, which is dedicated for the independent HP out and extra
inputs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch eventually fixes two issues:
- Handle the case where the primary output is a headphone and can have
  independent HP mode;
  so far we checked only the case where the headphone is the secondary
  output.

- Fix the conflict of HP independent mode and aamix mode;
  when switched to aamix mode, the DAC might be also switched to
  another widget shared with other outputs.  Then even if we disable
  the DAC for the original output, it doesn't change -- because the
  active route is from another (shared) DAC to HP pin through aamix.
  So, in such a case, we have to prohibit the switch to aamix for HP
  routes.

This fixes issues appearing on VT codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Many codecs provide routes to multiple output pins through an aamix
widget, but most of them do it only from a single DAC.  However, the
current generic parser checks only the aamix paths from the original
(directly bound) DACs through aamix NID, and miss the path:
  primary DAC -> aamix -> target out pin

This patch adds a more check for the routes like the above.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a patch couldn't be resolved in try_assign_dacs() although the
target DAC is expected, we forgot to add a proper badness value but
continued.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since fill_and_eval_dacs() may be called repeatedly with different
configurations, setting pinctls at each time there isn't optimal.
We can set it better only once after deciding the output configuration
in parse_output_paths().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Print the information of outputs in a bit more details and concisely
in a single place instead of printing the path at each time when
detected.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The patch "ALSA: hda - fix wrong adc_idx in generic parser" fixed the
adc_idx for the capture volume and capture switch controls.  But also
modified the adc_idx retrieval for the capture source controls
wrongly.  As multiple capture source controls are created in a single
shot with counts > 1, the id.index doesn't contain the real value.
The real index has to be taken via snd_ctl_get_ioffidx() as in the
original code.

This patch reverts the fixes partially to recover from the
regression.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just stumbled over this one while reading the code.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

I found a codec configuration which had six inputs, so the max of
five was not appropriate.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Although I commented that boost volumes would be added only for
line-in and mic pins in the source code, the actual code excludes but
for mic-in.  Fix it to accept the line-ins, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Two hooks in hda_gen_spec, cap_sync_hook and capture_switch_hook, play
very similar roles.  The only differences are that the former is
called more often (e.g. at init or switching capsrc) while the latter
can take an on/off argument.

As a more generic implementation, consolidate these two hooks, and
pass snd_ctl_elem_value pointer as the second argument.  If the
secondary argument is non-NULL, it can take the on/off value, so the
caller handles it like the former capture_switch_hook.  If it's NULL,
it's called in the init or capsrc switch case.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a standard capture switch without multiple binding is used, the
call for capture_switch_hook isn't called properly.  Replace the put
ops to add the hook call in that case.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the current generic parser code, we look for the (mic) boost
controls only on input pins.  But many codecs assign the boost volume
to a widget connected to each input pin instead of the input amp of
the pin itself.

In this patch, the parser tries to look through more widgets connected
to the pin and find a boost amp.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When an amp in the activation path is associated with mixer controls,
activate_amp() tries to skip the initialization.  It's good, but only
if the mixer really initializes both mute and volume.  Otherwise,
either the mute of the volume is left uninitialized.

This patch adds this missing check and properly initialize the
partially controlled amps in an activation path.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There are a few places creating the labels and indices of kctls for
each input pin in the current generic parser code.  This is redundant
and makes harder to maintain.  Let's create the labels and indices at
once and keep them in hda_gen_spec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the imux table entries can be a subset of autocfg.input table,
the indices of these aren't always same.  For passing the proper index
value of autocfg.input at creating input ctl labels (via
snd_hda_autocfg_input_label()), keep the corresponding autocfg.input
idx value in the index field of each imux item, which isn't used in
the generic driver.

Also, this makes easier to check the invalid imux pin for stereo mix.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the volume or mute control of the primary output is shared with
other (headphone or speaker) outputs, we shouldn't name it as a
specific output type but rather name it with the channel name or a
generic name like "PCM".

Also, this check should be performed individually for the volume and
the mute controls because some codecs may have shared volumes but
separate mute controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Not only PCM playback, a hook for PCM capture would be required for
power controls in codec drivers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.

This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config().  This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.

Note that ground and 100% vrefs are excluded from the list for
simplicity, currently.  We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag.  It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... to be referred by the codec driver.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

... and a little bit of code refactoring.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>