MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.

bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.

APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.

AK: added some ifdefs to make it compile on UP
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Original patch from Bertro Simul

This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This was just needed for the Numasaurus, which fortunately
doesn't support x86-64 CPUs.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When coming out of apic mode attempt to set the appropriate
apic back into virtual wire mode.  This improves on previous versions
of this patch by by never setting bot the local apic and the ioapic
into veritual wire mode.

This code looks at data from the mptable to see if an ioapic has
an ExtInt input to make this decision.  A future improvement
is to figure out which apic or ioapic was in virtual wire mode
at boot time and to remember it.  That is potentially a more accurate
method, of selecting which apic to place in virutal wire mode.
Signed-off-by: NEric Biederman <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A bug against an xSeries system showed up recently noting that the
check_nmi_watchdog() test was failing.

I have been investigating it and discovered in both i386 and x86_64 the
recent change to the routine to use the cpu_callin_map has uncovered a
problem.  Prior to that change, on an SMP box, the test was trivally
passing because all cpu's were found to not yet be online, but now with the
callin_map they are discovered, it goes on to test the counter and they
have not yet begun to increment, so it announces a CPU is stuck and bails
out.

On all the systems I have access to test, the announcement of failure is
also bougs...  by the time you can login and check /proc/interrupts, the
NMI count is happily incrementing on all CPUs.  Its just that the test is
being done too early.

I have tried moving the call to the test around a bit, and it was always
too early.  I finally hit on this proposed solution, it delays the routine
via a late_initcall(), seems like the right solution to me.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!