Skip to content

L
linux

xiphi1978 / linux

通知 2
Star 0
Fork 0
L
linux

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 04 9月, 2013 1 次提交
  3. 22 8月, 2013 1 次提交
    • M
      s390: convert interrupt handling to use generic hardirq · 1f44a225
      由 Martin Schwidefsky 提交于 
      With the introduction of PCI it became apparent that s390 should
convert to generic hardirqs as too many drivers do not have the
correct dependency for GENERIC_HARDIRQS. On the architecture
level s390 does not have irq lines. It has external interrupts,
I/O interrupts and adapter interrupts. This patch hard-codes all
external interrupts as irq #1, all I/O interrupts as irq #2 and
all adapter interrupts as irq #3. The additional information from
the lowcore associated with the interrupt is stored in the
pt_regs of the interrupt frame, where the interrupt handler can
pick it up. For PCI/MSI interrupts the adapter interrupt handler
scans the relevant bit fields and calls generic_handle_irq with
the virtual irq number for the MSI interrupt.
Reviewed-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      1f44a225
  5. 08 1月, 2013 2 次提交
  7. 18 12月, 2012 1 次提交
  9. 01 12月, 2012 1 次提交
    • J
      s390/pci: PCI adapter interrupts for MSI/MSI-X · 9a4da8a5
      由 Jan Glauber 提交于 
      Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.

Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      9a4da8a5
  11. 26 9月, 2012 2 次提交
    • J
      s390: add support for runtime instrumentation · e4b8b3f3
      由 Jan Glauber 提交于 
      Allow user-space threads to use runtime instrumentation (RI). To enable RI
for a thread there is a new s390 specific system call, sys_s390_runtime_instr,
that takes as parameter a realtime signal number. If the RI facility is
available the system call sets up a control block for the calling thread with
the appropriate permissions for the thread to modify the control block.

The user-space thread can then use the store and modify RI instructions to
alter the control block and start/stop the instrumentation via RION/RIOFF.

If the user specified program buffer runs full RI triggers an external
interrupt. The external interrupt is translated to a real-time signal that
is delivered to the thread that enabled RI on that CPU. The number of
the real-time signal is the number specified in the RI system call. So,
user-space can select any available real-time signal number in case the
application itself uses real-time signals for other purposes.

The kernel saves the RI control blocks on task switch only if the running
thread was enabled for RI. Therefore, the performance impact on task switch
should be negligible if RI is not used.

RI is only enabled for user-space mode and is disabled for the supervisor
state.
Reviewed-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      e4b8b3f3
    • S
      s390/eadm_sch: add support for irq statistics · 2e73c2cf
      由 Sebastian Ott 提交于 
      Add support for EADM interrupt statistics in /proc/interrupts.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      2e73c2cf
  13. 23 5月, 2012 1 次提交
  15. 23 3月, 2012 1 次提交
  17. 11 3月, 2012 1 次提交
    • H
      [S390] irq: external interrupt code passing · fde15c3a
      由 Heiko Carstens 提交于 
      The external interrupt handlers have a parameter called ext_int_code.
Besides the name this paramter does not only contain the ext_int_code
but in addition also the "cpu address" (POP) which caused the external
interrupt.
To make the code a bit more obvious pass a struct instead so the called
function can easily distinguish between external interrupt code and
cpu address. The cpu address field however is named "subcode" since
some external interrupt sources do not pass a cpu address but a
different parameter (or none at all).
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      fde15c3a
  19. 30 10月, 2011 3 次提交
  21. 26 5月, 2011 1 次提交
  23. 23 5月, 2011 1 次提交
  25. 05 1月, 2011 11 次提交
  27. 02 8月, 2008 1 次提交
  29. 30 9月, 2006 1 次提交
  31. 23 6月, 2006 1 次提交
    • J
      [PATCH] adjust handle_IRR_event() return type · 908dcecd
      由 Jan Beulich 提交于 
      Correct the return type of handle_IRQ_event() (inconsistency noticed during
Xen development), and remove redundant declarations.  The return type
adjustment required breaking out the definition of irqreturn_t into a
separate header, in order to satisfy current include order dependencies.
Signed-off-by: NJan Beulich <jbeulich@novell.com>

Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      908dcecd
  33. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4