pageattr-test.c contains a noisy debug printk that people reported.
The condition under which it prints (randomly tapping into a mem_map[]
hole and not being able to c_p_a() there) is valid behavior and not
interesting to report.

Remove it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
  kbuild: fix make V=1

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  selinux: support 64-bit capabilities

Without this patch a Opteron test system here oopses at boot with
current git.

Calling to_pci_dev() on a NULL pointer gives a negative value so the
following NULL pointer check never triggers and then an illegal address
is referenced.  Check the unadjusted original device pointer for NULL
instead.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://linux-nfs.org/~bfields/linux:
  SUNPRC: Fix printk format warning
  nfsd: clean up svc_reserve_auth()
  NLM: don't requeue block if it was invalidated while GRANT_MSG was in flight
  NLM: don't reattempt GRANT_MSG when there is already an RPC in flight
  NLM: have server-side RPC clients default to soft RPC tasks
  NLM: set RPC_CLNT_CREATE_NOPING for NLM RPC clients

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: remove stale comment from ide-lib.c
  ide: fix comment in init_irq()
  ide: ide_init_port() bugfix
  ide-disk: fix flush requests (take 2)
  ide: introduce CONFIG_BLK_DEV_IDEDMA_SFF option
  bast-ide: build fix
  ide-tape: remove never executed code
  ide: fix ide/legacy/gayle.c compilation
  ide-cd: replace ntohs with generic byteorder macro be16_to_cpu
  ide: remove stale version number
  pdc202xx_old: always enable burst mode
  palm_bk3710: use struct ide_port_info
  palm_bk3710: port initialization/probing bugfix
  palm_bk3710: fix ide_unregister() usage
  palm_bk3710: ide_register_hw() -> ide_device_add()
  ide: insert BUG_ON() into __ide_set_handler() (take 2)
  cs5520: remove stale comment
  ide: another possible ide panic fix for blk-end-request

When make -s support were added to filechk to
combination created with make V=1 were not
covered.
Fix it by explicitly cover this case too.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Mike Frysinger <vapier@gentoo.org>

Since we may not have a pci_dev for the device we need to access, we can't
use pci_read_config_word.  But raw_pci_read is an internal implementation
detail; it's better to use the architected pci_bus_read_config_word
interface.  Using PCI_DEVFN instead of a mysterious constant helps
reassure everyone that we really do intend to access device 8.

[ Thanks to Grant Grundler for pointing out to me that this is exactly
  what the write immediately above this is doing -- enabling device 8 to
  respond to config space cycles.
					- Matthew

  Grant also says:

	"Can you also add a comment which points at the Intel
	 documentation?

	 The 'Intel E7320 Memory Controller Hub (MCH) Datasheet' at

	  http://download.intel.com/design/chipsets/datashts/30300702.pdf

	 Page 69 documents register F4h (DEVPRES1).

	 And I just doubled checked that the 0xf4 register value is
	 restored later in the quirk (obvious when you look at the code
	 but not from the patch"

  so here it is.
					 - Linus ]
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Acked-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix SELinux to handle 64-bit capabilities correctly, and to catch
future extensions of capabilities beyond 64 bits to ensure that SELinux
is properly updated.
Signed-off-by: NStephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NJames Morris <jmorris@namei.org>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

APUS support is gone...
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Sunday 10 February 2008, Atsushi Nemoto wrote:
> On Sun, 06 Jan 2008 18:03:10 +0100, Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> wrote:
> > +	/* reset DMA masks only for SFF-style DMA controllers */
> > +	if ((d->host_flags && IDE_HFLAG_NO_DMA) == 0 && hwif->dma_base == 0)
> > +		hwif->swdma_mask = hwif->mwdma_mask = hwif->ultra_mask = 0;
> 
> It might be too late, but "host_flags && IDE_HFLAGS_NO_DMA" seems
> wrong for me.

Fix regression caused by commmit c413b9b9
("ide: add struct ide_port_info instances to legacy host drivers").
Reported-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

commit 813a0eb2
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Fri Jan 25 22:17:10 2008 +0100

    ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests

...

broke flush requests.

Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:

- idedisk_prepare_flush() only prepares the request and it doesn't wait
  for it to be completed

- there are can be multiple flush requests queued in the queue

Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
  (while at it rename 'args' to 'task' and fix whitespace damage)

[ This will be fixed properly before 2.6.25 but this bug is rather
  critical and the proper solution requires some more work + testing. ]

Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: NSebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Saturday 09 February 2008, Adrian Bunk wrote:
> Commit 9e016a71 causes the following 
> compile error:
> 
> <--  snip  -->
> 
> ...
>   CC      drivers/ide/arm/bast-ide.o
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c: In function 'bastide_register':
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:31: error: 'hwif' redeclared as different kind of symbol
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:29: error: previous definition of 'hwif' was here
> make[4]: *** [drivers/ide/arm/bast-ide.o] Error 1
> 
> <--  snip  -->

Remove 'ide_hwif_t **hwif' argument from bastide_register()
(together with write-only ifs[]).

Cc: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

rq->cmd[0] is never set to REQ_IDETAPE_READ_BUFFER so remove
REQ_IDETAPE_READ_BUFFER handling from idetape_create_write_cmd()
and the define itself.

Then remove no longer used idetape_create_read_buffer_cmd()
and IDETAPE_RETRIEVE_FAULTY_BLOCK define.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Thursday 03 January 2008, Robert Hancock wrote:

[...]

> How about getting rid of this stupid thing in drivers/ide/ide.c:
> 
> #define       REVISION        "Revision: 7.00alpha2"
> 
> which is used in:
> 
> printk(KERN_INFO "Uniform Multi-Platform E-IDE driver " REVISION "\n");
> 
> It's been 7.00alpha2 for god knows how long, so clearly this version 
> number is not useful..

Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).

Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out cable detection to palm_bk3710_cable_detect().

* Add palm_bk3710_init_hwif() (->init_hwif method implementation).

* Remove needless ->quirkproc initialization.

* Add missing ->pio_mask initialization.

* Use ATA_* defines for setting ->{ultra,mwdma}_mask.

* Add 'struct ide_port_info palm_bk3710_port_info' and pass it to
  ide_device_add().  Then remove open-coded 'hwif' initialization.

Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Probe port _after_ it is fully initialized.

Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't set 'restore' flag for ide_unregister() when initializing new
interface.

[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
  by commit 909f4369 ]

Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert palm_bk3710 host driver to use ide_device_add() instead of
  ide_register_hw() (while at it drop doing "ide_unregister()" loop which
  tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
  cannot be find).

  [ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
    by commit 9e016a71 ]

* Rename 'ide_ctlr_info' to 'hw' and 'index' to 'i' while at it.

Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Replace the check for hwgroup->handler and printk(KERN_CRIT, ...) at the start
of __ide_set_handler() with mere BUG_ON() while removing such from the caller,
ide_execute_command(). Fix up the code formatting, while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove stale comment from the cs5520 IDE driver.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

I have reviewed all blk-end-request patches again to confirm whether
there are any similar problems with the last week's ide-cd panic:
    http://lkml.org/lkml/2008/1/29/140

And I found a possible similar bug in ide-io change:
ide_end_drive_cmd() could be called for blk_pc_request() which could
have bios.  To complete such requests correctly, we need to pass
the actual size of the request.
Otherwise, __blk_end_request() returns 1 because the request still has
bios, and the system will BUG() unnecessarily.

The following patch fixes the bug and should be applied on top of
Linus' git.
Signed-off-by: NKiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

net/sunrpc/xprtrdma/svc_rdma_sendto.c:160: warning: format '%llx'
expects type 'long long unsigned int', but argument 3 has type 'u64'
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>

This is a void function attempting to return the return value from
another void function, which seems harmless but extremely weird, and
apparently makes some compilers complain.

While we're there, clean up a little (e.g. the switch statement had a
minor style problem and seemed overkill as long as there's only one
case).

Thanks to Trond for noticing this.
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>

It's possible for lockd to catch a SIGKILL while a GRANT_MSG callback
is in flight. If this happens we don't want lockd to insert the block
back into the nlm_blocked list.

This helps that situation, but there's still a possible race. Fixing
that will mean adding real locking for nlm_blocked.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>

With the current scheme in nlmsvc_grant_blocked, we can end up with more
than one GRANT_MSG callback for a block in flight. Right now, we requeue
the block unconditionally so that a GRANT_MSG callback is done again in
30s. If the client is unresponsive, it can take more than 30s for the
call already in flight to time out.

There's no benefit to having more than one GRANT_MSG RPC queued up at a
time, so put it on the list with a timeout of NLM_NEVER before doing the
RPC call. If the RPC call submission fails, we requeue it with a short
timeout. If it works, then nlmsvc_grant_callback will end up requeueing
it with a shorter timeout after it completes.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>

Now that it no longer does an RPC ping, lockd always ends up queueing
an RPC task for the GRANT_MSG callback. But, it also requeues the block
for later attempts. Since these are hard RPC tasks, if the client we're
calling back goes unresponsive the GRANT_MSG callbacks can stack up in
the RPC queue.

Fix this by making server-side RPC clients default to soft RPC tasks.
lockd requeues the block anyway, so this should be OK.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>

It's currently possible for an unresponsive NLM client to completely
lock up a server's lockd. The scenario is something like this:

1) client1 (or a process on the server) takes a lock on a file
2) client2 tries to take a blocking lock on the same file and
   awaits the callback
3) client2 goes unresponsive (plug pulled, network partition, etc)
4) client1 releases the lock

...at that point the server's lockd will try to queue up a GRANT_MSG
callback for client2, but first it requeues the block with a timeout of
30s. nlm_async_call will attempt to bind the RPC client to client2 and
will call rpc_ping. rpc_ping entails a sync RPC call and if client2 is
unresponsive it will take around 60s for that to time out. Once it times
out, it's already time to retry the block and the whole process repeats.

Once in this situation, nlmsvc_retry_blocked will never return until
the host starts responding again. lockd won't service new calls.

Fix this by skipping the RPC ping on NLM RPC clients. This makes
nlm_async_call return quickly when called.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>

.. and I really need to call it something else.  Maybe it is time to
bring back the weasel series, since weasels always make me feel good
about a kernel.

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
  [ARM] constify function pointer tables
  [ARM] 4823/1: AT91 section fix
  [ARM] 4824/1: pxa: clear RDH bit after any reset
  [ARM] pxa: remove debugging PM: printk
  ARM: OMAP1: Misc clean-up
  ARM: OMAP1: Update defconfigs for omap1
  ARM: OMAP1: Palm Tungsten E board clean-up
  ARM: OMAP1: Use I2C bus registration helper for omap1
  ARM: OMAP1: Remove omap_sram_idle()
  ARM: OMAP1: PM fixes for OMAP1
  ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
  ARM: OMAP1: Make omap1 use MMC multislot structures
  ARM: OMAP1: Change the comments to C style
  ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
  ARM: OMAP: Add helper module for board specific I2C bus registration
  ARM: OMAP: Add dmtimer support for OMAP3
  ARM: OMAP: Pre-3430 clean-up for dmtimer.c
  ARM: OMAP: Add DMA support for chaining and 3430
  ARM: OMAP: Add 24xx GPIO debounce support
  ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
  ...

We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86.  Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Thanks to Loic Prylli <loic@myri.com>, who originally proposed
this idea.

Always using legacy configuration mechanism for the legacy config space
and extended mechanism (mmconf) for the extended config space is
a simple and very logical approach. It's supposed to resolve all
known mmconf problems. It still allows per-device quirks (tweaking
dev->cfg_size). It also allows to get rid of mmconf fallback code.
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [PKT_SCHED] ematch: Fix build warning.

* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
  hrtimer: don't modify restart_block->fn in restart functions
  hrtimer: fix *rmtp/restarts handling in compat_sys_nanosleep()
  hrtimer: fix *rmtp handling in hrtimer_nanosleep()
  ntp: correct inconsistent interval/tick_length usage

Commit 8811930d ("splice: missing user
pointer access verification") added the proper access_ok() calls to
copy_from_user_mmap_sem() which ensures we can copy the struct iovecs
from userspace to the kernel.

But we also must check whether we can access the actual memory region
pointed to by the struct iovec to fix the access checks properly.
Signed-off-by: NBastian Blank <waldi@debian.org>
Acked-by: NOliver Pinter <oliver.pntr@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>