write_cache_pages() uses i_mapping->writeback_index to pick up where it
left off the last time a given inode was found by pdflush or
balance_dirty_pages (or anyone else who sets wbc->range_cyclic)

alloc_inode() should set it to a sane value so that writeback doesn't
start in the middle of a file.  It is somewhat difficult to notice the bug
since write_cache_pages will loop around to the start of the file and the
elevator helps hide the resulting seeks.

For whatever reason, Btrfs hits this often.  Unpatched, untarring 30
copies of the linux kernel in series runs at 47MB/s on a single sata
drive.  With this fix, it jumps to 62MB/s.
Signed-off-by: NChris Mason <chris.mason@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add MAINTAINERS for GRU, XPNET, XPC and XP drivers.
Signed-off-by: NJack Steiner <steiner@sgi.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add in the CPUID for Nehalem chips.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, all sensors are read when the energy meter is queried via
sysfs.  This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use.  Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On older machines, probing for a nonexistent AEM interface returned an
IPMI error; when we saw this, we'd stop probing.  On the x3650 M2 and
(presumably) later, we are returned a value indicating success and a
buffer full of garbage or zeroes.  This causes the probe function to run
in an infinite loop.  To fix this, we add one last check--if the
interface number we're looking for is higher than the number of
interfaces that AEM claims to have, stop probing.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previously the driver was only using DMI to prevent smbus probing on
non-Abit motherboards.  However, since the manual probing method is
brittle and prone to failure on some Abit motherboards (esp.  the Abit
IP35 Pro) it is better to use DMI to also read the board name and then
decide whether or not to probe the bus.

At the moment, we do not have a list of valid DMI name strings to use
for existing and supported motherboards.  This patch only implements DMI
probing for the IP35 Pro.  For motherboards that can not yet use DMI
probing, a warning will be printed to the kernel log asking those users
to email me their dmidecode output.

The existing manual probing mechanism will be used if CONFIG_DMI is not
enabled, if DMI probing fails (for DMI-unsupported motherboards), or if
DMI probing fails and the "force" option is set (for DMI-supported
motherboards).  Ideally in the longer term this manual probing method
would be removed.

This patch should be safe to apply as it does not change the probing
behaviour for most of the supported motherboards, just the IP35 Pro,
which already has regressions filed against it in 2.6.26.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11212Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hans passed maintainership of the abituguru3 hwmon driver onto me.  Add
a new entry to the MAINTAINERS file for the abituguru3 driver and assign
it to me.  Also update the existing UGURU entry to indicate that Hans is
only responsible for the abituguru driver.
Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Export the sensor -> channel/dimm mapping in tempX_label.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...

Code for 8 channels by Tobias Himmer.

This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:

 * bb  is the resolution in number of bits (8, 10, 12)
 * c   is the number of channels (1, 2, 4, 8)
 * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
   kSPS and 101 for 1 MSPS)

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/hwmon/w83791d.c: In function `w83791d_probe':
drivers/hwmon/w83791d.c:1049: warning: unused variable `val1'
Signed-off-by: NMichael Borisov <niro@tut.by>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for Macbook v3 (sensors and accelerometer).
Signed-off-by: NNicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for fans and temperature sensors on intel iMac.

Tested on iMac 24" 2.8ghz (iMac8,1), it supports the following sensors:

cpu A
ambient
gpu
gpu diode
gpu heatsink
hd bay 1
memory controller
optical drive
power
Signed-off-by: NRoberto De Ioris <roberto@unbit.it>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

AOI position cannot be negative.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Application can now have the virtual resoltuion and use FBIOPAN_DISPLAY
ioctl to pan.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Functionally the same, but more conventional.

Cc: Huang Ying <ying.huang@intel.com>
Tested-by: NVivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ftrace depends on some processor state that we destroyed during kexec and
restored by restore_processor_state().  So save_processor_state() and
restore_processor_state() are moved into machine_kexec() and ftrace is
restored after restore_processor_state().
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add __ftrace_enabled_save/restore, used to disable ftrace for a while.
Now, this is used by kexec jump, which need a version without lock, for
general situation, a locked version should be used.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add device_pm_lock() and device_pm_unlock() in kernel_kexec() in sync with
current hibernation implementation.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Call kernel_restart_prepare() in kernel_kexec() instead of duplicating the
code.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Acked-by: NPavel Machek <pavel@suse.cz>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kexec/Kexec-jump require code size in control page is less than
PAGE_SIZE/2.  This patch add link-time checking for this.

ASSERT() of ld link script is used as the link-time checking mechanism.

[akpm@linux-foundation.org: build fix]
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE, because control
page is used for not only code on some platform.  For example in kexec
jump, it is used for data and stack too.

[akpm@linux-foundation.org: unbreak powerpc and arm, finish conversion]
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move if (kexec_image->preserve_context) { ...  } into #ifdef
CONFIG_KEXEC_JUMP to make code looks cleaner.

Fix no longer correct comments of kernel_kexec().
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Acked-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kernel/kexec.c: In function 'kernel_kexec':
kernel/kexec.c:1506: warning: value computed is not used
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

WARNING: vmlinux.o(.text+0xe684): Section mismatch in reference from the function register_nosave_region() to the function .init.text:__register_nosave_region()
  The function register_nosave_region() references
  the function __init __register_nosave_region().
  This is often because register_nosave_region lacks a __init
  annotation or the annotation of __register_nosave_region is wrong.

register_nosave_region calls __init function and is called only from
__init functions
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With man-pages-3.07, the numa_maps documentation home is now proc(5), so
the reference in Documentation/vm/page_migration needs updating.
(Cliff/Lee are removing numa_maps.5 from the numactl package.) Also, the
download location for the numactl package changed a while back.  This
patch fixes both things, as well as a typo (provided-->provides).
Signed-off-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Cc: Cliff Wickman <cpw@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the minimal sequence that jams the allocator:

void *p, *q, *r;
p = alloc_bootmem(PAGE_SIZE);
q = alloc_bootmem(64);
free_bootmem(p, PAGE_SIZE);
p = alloc_bootmem(PAGE_SIZE);
r = alloc_bootmem(64);

after this sequence (assuming that the allocator was empty or page-aligned
before), pointer "q" will be equal to pointer "r".

What's hapenning inside the allocator:
p = alloc_bootmem(PAGE_SIZE);
in allocator: last_end_off == PAGE_SIZE, bitmap contains bits 10000...
q = alloc_bootmem(64);
in allocator: last_end_off == PAGE_SIZE + 64, bitmap contains 11000...
free_bootmem(p, PAGE_SIZE);
in allocator: last_end_off == PAGE_SIZE + 64, bitmap contains 01000...
p = alloc_bootmem(PAGE_SIZE);
in allocator: last_end_off == PAGE_SIZE, bitmap contains 11000...
r = alloc_bootmem(64);

and now:

it finds bit "2", as a place where to allocate (sidx)

it hits the condition

if (bdata->last_end_off && PFN_DOWN(bdata->last_end_off) + 1 == sidx))
start_off = ALIGN(bdata->last_end_off, align);

-you can see that the condition is true, so it assigns start_off =
ALIGN(bdata->last_end_off, align); (that is PAGE_SIZE) and allocates
over already allocated block.

With the patch it tries to continue at the end of previous allocation only
if the previous allocation ended in the middle of the page.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Acked-by: NJohannes Weiner <hannes@saeurebad.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
  usb: musb: pass configuration specifics via pdata
  usb: musb: fix hanging when rmmod gadget driver
  USB: Add MUSB and TUSB support
  USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
  USB: Add vendor/product id of ZTE MF628 to option
  USB: quirk PLL power down mode
  USB: omap_udc: fix compilation with debug enabled
  usb: cdc-acm: drain writes on close
  usb: cdc-acm: stop dropping tx buffers
  usb: cdc-acm: bugfix release()
  usb gadget: issue notifications from ACM function
  usb gadget: remove needless struct members
  USB: sh: r8a66597-hcd: fix disconnect regression
  USB: isp1301: fix compilation
  USB: fix compiler warning fix
  usb-storage: unusual_devs entry for Nokia 5300
  USB: cdc-acm.c: Fix compile warnings
  USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver
  USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
  usb: isp1760: don't be noisy about short packets.
  ...

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  CRED: Introduce credential access wrappers

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
  netns: Fix crash by making igmp per namespace
  bnx2x: Version update
  bnx2x: Checkpatch compliance
  bnx2x: Spelling mistakes
  bnx2x: Minor code improvements
  bnx2x: Driver info
  bnx2x: 1G LED does not turn off
  bnx2x: 8073 PHY changes
  bnx2x: Change GPIO for any port
  bnx2x: Pause settings
  bnx2x: Link order with external PHY
  bnx2x: No LRO without Rx checksum
  bnx2x: Wrong structure size
  bnx2x: WoL capability
  bnx2x: Clearing MAC addresses filters
  bnx2x: Delay in while loops
  bnx2x: PBA Table Page Alignment Workaround
  bnx2x: Self-test false positive
  bnx2x: Memory allocation
  bnx2x: HW attention lock
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Handle stack trace attempts before irqstacks are setup.
  sparc64: Implement IRQ stacks.
  sparc: remove include of linux/of_device.h from asm/of_device.h
  sparc64: Fix recursion in stack overflow detection handling.
  sparc/drivers: use linux/of_device.h instead of asm/of_device.h
  sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.

Use platform_data to pass musb configuration-specific
details to musb driver.

This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.

The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.

Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These drivers should not be relying on CONFIG_USB_DEBUG.  By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.

Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: NOliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.

PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: NCrane Cai <crane.cai@amd.com>
Signed-off-by: NLibin Yang <libin.yang@amd.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data.  There
is a timeout, so it can't wait too long.

Provide missing locking inside acm_wb_is_avail(); it matters
more now.  Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.

Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!).  This patch removes them:

  - The write_ready flag ... if an URB and buffer were found,
    they can (and should!) always be used.

  - TX path acm_wb_is_used() ... used when the buffer was just
    allocated, so that check is pointless.

Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc:  David Engraf <david.engraf@netcom.eu>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>