Add a shutdown method to spu_sysdev_class to allow proper spu resource
cleanup on system shutdown.  This is needed to support kexec on the PS3
platform.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On Power machines supporting VRMA, Kexec/Kdump does not work.
VRMA (virtual real-mode area) means that accesses with IR/DR = 0
(i.e. the MMU "off") actually still go through the hash table,
using entries put there by the hypervisor.

This means that when we clear out the hash table on kexec, we need to
make sure these entries are left untouched.

This also adds plpar_pte_read_raw() on the lines of
plpar_pte_remove_raw().

Signed-off-by : Sachin Sant <sachinp@in.ibm.com>
Signed-off-by : Mohan Kumar M <mohan@in.ibm.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In some of the PPC970 based systems, interrupt would be distributed to
offline cpus also even when booted with "maxcpus=1".  So check whether
cpu online map and cpu present map are equal or not.  If they are equal
default_distrib_server is used as interrupt server otherwise boot cpu
(default_server) used as interrupt server.

In addition to this, if an interrupt is assigned to a specific cpu (ie
smp affinity) and if that cpu is not online, the earlier code used to
return the default_distrib_server as interrupt server.  This
introduces an additional parameter to the get_irq function, called
strict_check.  Based on this parameter, if the cpu is not online
either default_distrib_server or -1 is returned.
Signed-off-by: NMohan Kumar M <mohan@in.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Acked-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On pSeries the firmware features are not setup until ppc_md.init_early,
so we can't do the firmware feature sections fixups till after this.

Currently firmware feature sections is only used on iSeries which inits
the firmware features much earlier.  This is a bug in waiting on
pSeries.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

For POWERPC, stolen time accounts for cycles lost to the hypervisor or
PURR cycles attributed to the other SMT thread.  Hence, when a PURR is
available, we should still calculate stolen time, irrespective of being
virtualised.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Specifying 'console=ttyMM0' on the cmdline for the prmpc2800 is no
longer necessary.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When a Marvell MPSC (serial controller) port is the specified
/chosen/stdout-path device, call 'add_preferred_console()' so the user
doesn't have to specify a 'console=ttyMMx' cmdline argument.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Acked-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch adds irq_create_direct_mapping().  This routine is
an alternative to irq_create_mapping(), for irq controllers that
can use linux virq numbers directly as hardware numbers.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A future patch will need the logic at the end of irq_create_mapping()
which setups a virq and installs it in the irq_map. So split it out
into a new function irq_setup_virq().
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Uninline virq_to_hw and export it so modules can use it.  The alternative
would be to export the irq_map array instead, but it's an infrequently
called function, and keeping the array unexported seems considerably
cleaner.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The holly support currently has separate rules to wrap its device tree
with its zImage.  This can now be done automatically without the extra
rules so update holly support to use the automatic feature.
Signed-off-by: NMark A. Greer <mgreer@mista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There are 2 config options that indicate whether the platform being built
has a device tree source file associated with it.  Namely,
CONFIG_WANT_DEVICE_TREE and CONFIG_DEVICE_TREE.  When CONFIG_WANT_DEVICE_TREE
is 'y' and CONFIG_DEVICE_TREE isn't an empty string, automatically wrap
the specified device tree with the zImage being built.

To achieve this, the 'dts' variable will only be set when the conditions
above are true.  The changes to the zImage.initrd.% and zImage.% rules
cause the device tree to be wrapped when 'dts' is set; otherwise, they
will work as they previosly did (i.e., build a zImage with no device tree).
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Being able to selectively wrap a device tree with the zIimage at build
time has been deemed unnecessary, so this removes Makefile support for
that feature.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

cpu_purr_data is a per-cpu array used to account for stolen time on
partitioned systems.  It used to be the case that cpus accessed each
others' cpu_purr_data, so each entry was protected by a spinlock.

However, the code was reworked ("Simplify stolen time calculation")
with the result that each cpu accesses its own cpu_purr_data and not
those of other cpus.  This means we can get rid of the spinlock as
long as we're careful to disable interrupts when accessing
cpu_purr_data in process context.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

With both generic rtc and powerpc timer suspend / resume code now in the
(powerpc.git) tree, powerpc platforms using the generic timer and enabling
power management will have timer.o linked in the kernel, which they don't
need. Moreover, it will likely WARN_ON(!ppc_md.get_rtc_time), save
zero-time and return no error on suspend...

As a possible solution we can choose not to build timer.o when RTC_CLASS
is enabled.  However, I can imagine systems with 2 rtc's, one served by the
ppc-rtc, another one generic built as a module, in which case using the
ppc-rtc for suspend / resume will be impossible.  Not to say, that such a
configuration would be ugly...
Signed-off-by: NG. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Glue code to hook up the pata_platform on the PA Semi Electra eval board.
CFE sets up device tree entries for the IDE interface, with device type
'ide' and compatible field 'electra-ide'.

We unfortunately need to modify the resources before calling the generic
platform driver, since the device tree only has one register window in
it and the driver expects two.  Adding this as an of_platform driver
instead doesn't give us any benefit, it just adds one more layer of
register/probe functions.

Since CONFIG_PATA_PLATFORM depends on CONFIG_EMBEDDED, add that as a
default for PPC_PASEMI.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes the timer sysdev use mktime instead of rtc_tm_to_time,
since rtc_tm_to_time just calls mktime anyway, and this means we
don't have a dependency on rtc-lib.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

With this, when kexec-ing, we copy the code and start the slaves on
their journey to the next kernel's spin loop as soon as we copy the
kexec image into place.

The kernel doesn't know exactly which slaves are spinning in
kexec_wait.  This allows us to pass more than max-cpus to the
next kernel.  But it also means that we might leave some behind.

Moving the code here means they have the time it takes us to
clear the hash table to wake up and move on.  Moving the code
any earlier would reuqire walking the image description to
search for the code, which could span multiple pages.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes some problems with the way the some things
represented in the device tree for the Holly and Taiga boards.  This
means changes both to the dts files, and to the code which
instantiates the tsi108 ethernet platform devices based on the device
tree.

	- First, and most importantly, the ethernet PHYs are given
with an identical 'reg' property.  This reg currently encodes the
accessible register used to initiate mdio interaction with the PHYs,
rather than a meaningful address on the parent bus (mdio in this
case), which is incorrect.  Instead we give the address of these
registers as 'reg' in the mdio node itself, and encode the ID of each
phy in their 'reg' propertyies.
	- Currently the platform device constructor enables a
workaround in the tsi108 ethernet driver based on the compatible
property of the PHY.  This is incorrect, because the workaround in
question is necessary due to the board's wiring of the PHY, not the
model of PHY itself.  This patch alters the constructor to instead
enable the workaround based on a new special property in the PHY node.
	- The compatible properties on a number of nodes in the device
tree are insufficiently precise.  In particular the PHYs give only
"bcm54xx", which is broken, since there are many bcm54xx PHY models,
and they have differences which matter.  The mdio had a compatible
property of "tsi-ethernet" identical to the ethernet MAC nodes, which
doesn't make sense.  The ethernet, i2c, bridge and PCI nodes were
given only as "tsi-*" which is somewhat inprecise, we replace with
"tsi108-*" in the case of Taiga (which has a TSI108 bridge), and
"tsi109-*", "tsi108-*" in the case of Holly (which has a TSI109
bridge).
	- We remove some "model" properties from the ethernets on
Taiga board which were neither useful nor adequately precise.
	- On Holly we change to using a dtc label instead of a full
path to reference the MPIC node, which makes the dts a little more
readable.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently, the Holly device tree includes a bootargs property in
/chosen, which gives a commandline.  This is somewhat inconvenient,
because it means an alternative default command line can't be given in
the kernel config - the value obtained from the dts via the
bootwrapper will always override CONFIG_CMDLINE.

This removes the command line from the dts, and instead puts the
same command line as a default in holly_defconfig.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The various cuboot platforms (i.e. pre-device tree aware u-boot for
83xx, 85xx and Ebony) share a certain amount of code for parsing the
boot parameters.  To a certain extent that's inevitable, since they
platforms have different definitions of the bd_t structure.  However,
with some macro work and a helper function, this patch improves the
situation a bit.

In the process, this fixes a bug on Ebony, which was incorrectly
handling the parameters passed form u-boot for the command line (the
bug was copied from 83xx and 85xx which have subsequently been fixed).
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In the device tree for Ebony, the 'ranges' property in the node for
the EBC bridge shows the mappings from the chip select / address lines
actually used for the EBC peripherals into the address space of the
OPB.  At present, these mappings are hardcoded in ebony.dts for the
mappings set up by the OpenBIOS firmware when it configures the EBC
bridge.

This replaces the hardcoded mappings with code in the zImage to
read the EBC configuration registers and create an appropriate ranges
property based on them.  This should make the zImage and kernel more
robust to changes in firmware configuration.  In particular, some of
the Ebony's DIP switches can change the effective address of the Flash
and other peripherals in OPB space.  With this patch, the kernel will
be able to cope with at least some of the possible variations.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ebony_exit() function which resets the Ebony board should in fact
be common to most if not all 44x boards.  This moves the function out
into 44x.c, renaming it, so it can be used by other 44x platforms.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially).  It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.

In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).

This tries to clarify the situation a little.  The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified.  We check this, instead of
SPLIT_ID_CACHE nearly everywhere.

The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200.  In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature.  The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.

This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Using typedefs to rename structure types if frowned on by CodingStyle.
However, we do so for the hash PTE structure on both ppc32 (where it's
called "PTE") and ppc64 (where it's called "hpte_t").  On ppc32 we
also have such a typedef for the BATs ("BAT").

This removes this unhelpful use of typedefs, in the process
bringing ppc32 and ppc64 closer together, by using the name "struct
hash_pte" in both cases.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This factors some things defined in both pgtable-ppc32.h and
pgtable-ppc64.h into the common part of asm-powerpc/pgtable.h.  These
are all things which have essentially identical definitions, and which
by their nature are very unlikely ever to need different definitions
in the two cases.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

In arch/powerpc/mm/pgtable_32.c, the variable io_bat_index and the
macro is_power_of_4() no longer have any users.  This removes them.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

APUS (the Amiga Power-Up System) is not supported under arch/powerpc
and it's unlikely it ever will be.  Therefore, this patch removes the
fragments of APUS support code from arch/powerpc which have been
copied from arch/ppc.

A few APUS references are left in asm-powerpc in .h files which are
still used from arch/ppc.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

These old-fashioned IO mapping functions no longer have any callers in
code which remains relevant on arch/powerpc.  Therefore, this removes
them from arch/powerpc.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

arch/powerpc still relies on asm-ppc/mmu.h for most 32-bit MMU types.
This is another step towards fixing this.  It takes the portions
of asm-ppc/mmu.h related to the "classic" 32-bit hash page table MMU
which are still relevant in arch/powerpc and puts them in a new
asm-powerpc/mmu-hash32.h, included when appropriate from
asm-powerpc/mmu.h.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently, all OF-related code in the bootloader is contained in of.c.
of.c also provides the platform specific things necessary to boot on
an OF platform.

However, there are platforms (such as PReP) which can include an OF
implementation, but are not bootable as pure OF systems.  For use by
such platforms, this patch splits out the low-level parts of the OF
code (call_prom() and various wrappers thereof) into a new oflib.c
file.  In addition, the code related to bootwrapper console output via
OF are moved to a new ofconsole.c file.  Both these files are included
in the wrapper.a library where they can be used by both full-OF and
partial OF platforms.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A lot of the options in arch/powerpc/Kconfig deal with the CPU menu,
and my next patches add more to them.  Moving them to a new
arch/powerpc/platforms/Kconfig.cputype file makes it easier to
follow.

There are no functional changes in here.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.

Killing just one of the process threads can leave the application in a
bad state, whereas killing the entire process group would allow for
the application to restart, or be otherwise handled, and makes it very
obvious that something has gone wrong.

This change allows the entire process group to be taken down, rather than
just the one thread.

lightly tested on powerpc
Signed-off-by: NWill <will_schmidt@vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).

This enables that to work properly on P6.

This just involves setting a bit in the CAS structure as well as the
VPA.  To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA.  Then call H_CEDE.

The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.

Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: NJake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch moves things around a little bit in the new common signal.c
and signal.h files to remove the last #ifdef in the middle of the
common do_signal().
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

set_dabr() and thread.dabr exist on 32 bits as well nowadays (they
actually may do something even, depending on what CPU you have).

So this removes the ifdef.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The code for creating signal frames was still duplicated and split
in strange ways between 32 and 64 bits, including the SA_ONSTACK
handling being in do_signal on 32 bits but inside handle_rt_signal
on 64 bits etc...

This moves the 64 bits get_sigframe() to the generic signal.c,
cleans it a bit, moves the access_ok() call done by all callers to
it as well, and adapts/cleanups the 3 different signal handling cases
to use that common function.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The powerpc signal code still had some obsolete freezer bits that
have long been removed from x86 (it's now done in generic code).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

do_signal has exactly the same behaviour on 32bit and 64bit and 32bit
compat on 64bit for handling 32bit signals.  Consolidate all these
into one common function in signal.c.  The only odd left over is
the try_to_free in the 32bit version that no other architecture has
in mainline (only in i386 for some odd SuSE release).  We should
probably get rid of it in a separate patch.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>