- 12 8月, 2007 40 次提交
-
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
-
由 Len Brown 提交于
Use DMI to: 1. enable polling (BIOS thermal events are broken) 2. disable active trip points (BIOS fan control is broken) 3. disable passive trip point (BIOS hard-codes it too low) The actual temperature reading does work, and with the aid of polling, the critical trip point should work too. http://bugzilla.kernel.org/show_bug.cgi?id=8842Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Len Brown 提交于
thermal.act=-1 disables all active trip points in all ACPI thermal zones. thermal.act=C, where C > 0, overrides all lowest temperature active trip points in all thermal zones to C degrees Celsius. Raising this trip-point may allow you to keep your system silent up to a higher temperature. However, it will not allow you to raise the lowest temperature trip point above the next higher trip point (if there is one). Lowering this trip point may kick in the fan sooner. Note that overriding this trip-point will disable any BIOS attempts to implement hysteresis around the lowest temperature trip point. This may result in the fan starting and stopping frequently if temperature frequently crosses C. WARNING: raising trip points above the manufacturer's defaults may cause the system to run at higher temperature and shorten its life. Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Len Brown 提交于
thermal.nocrt=1 disables actions on _CRT and _HOT ACPI thermal zone trip-points. They will be marked as <disabled> in /proc/acpi/thermal_zone/*/trip_points. There are two cases where this option is used: 1. Debugging a hot system crossing valid trip point. If your system fan is spinning at full speed, be sure that the vent is not clogged with dust. Many laptops have very fine thermal fins that are easily blocked. Check that the processor fan-sink is properly seated, has the proper thermal grease, and is really spinning. Check for fan related options in BIOS SETUP. Sometimes there is a performance vs quiet option. Defaults are generally the most conservative. If your fan is not spinning, yet /proc/acpi/fan/ has files in it, please file a Linux/ACPI bug. WARNING: you risk shortening the lifetime of your hardware if you use this parameter on a hot system. Note that this refers to all system components, including the disk drive. 2. Working around a cool system crossing critical trip point due to erroneous temperature reading. Try again with CONFIG_HWMON=n There is known potential for conflict between the the hwmon sub-system and the ACPI BIOS. If this fixes it, notify lm-sensors@lm-sensors.org and linux-acpi@vger.kernel.org Otherwise, file a Linux/ACPI bug, or notify just linux-acpi@vger.kernel.org. Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Len Brown 提交于
"thermal.psv=-1" disables passive trip points for all ACPI thermal zones. "thermal.psv=C", where 'C' is degrees Celsius, overrides all existing passive trip points for all ACPI thermal zones. thermal.psv is checked at module load time, and in response to trip-point change events. Note that if the system does not deliver thermal zone temperature change events near the new trip-point, then it will not be noticed. To force your custom trip point to be noticed, you may need to enable polling: eg. thermal.tzp=3000 invokes polling every 5 minutes. Note that once passive thermal throttling is invoked, it has its own internal Thermal Sampling Period (_TSP), that is unrelated to _TZP. WARNING: disabling or raising a thermal trip point may result in increased running temperature and shorter hardware lifetime on some systems. Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Len Brown 提交于
Thermal Zone Polling frequency (_TZP) is an optional ACPI object recommending the rate that the OS should poll the associated thermal zone. If _TZP is 0, no polling should be used. If _TZP is non-zero, then the platform recommends that the OS poll the thermal zone at the specified rate. The minimum period is 30 seconds. The maximum period is 5 minutes. (note _TZP and thermal.tzp units are in deci-seconds, so _TZP = 300 corresponds to 30 seconds) If _TZP is not present, ACPI 3.0b recommends that the thermal zone be polled at an "OS provided default frequency". However, common industry practice is: 1. The BIOS never specifies any _TZP 2. High volume OS's from this century never poll any thermal zones Ie. The OS depends on the platform's ability to provoke thermal events when necessary, and the "OS provided default frequency" is "never":-) There is a proposal that ACPI 4.0 be updated to reflect common industry practice -- ie. no _TZP, no polling. The Linux kernel already follows this practice -- thermal zones are not polled unless _TZP is present and non-zero. But thermal zone polling is useful as a workaround for systems which have ACPI thermal control, but have an issue preventing thermal events. Indeed, some Linux distributions still set a non-zero thermal polling frequency for this reason. But rather than ask the user to write a polling frequency into all the /proc/acpi/thermal_zone/*/polling_frequency files, here we simply document and expose the already existing module parameter to do the same at system level, to simplify debugging those broken platforms. Note that thermal.tzp is a module-load time parameter only. Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Len Brown 提交于
"thermal.off=1" disables all ACPI thermal support at boot time. CONFIG_ACPI_THERMAL=n can do this at build time. "# rmmod thermal" can do this at run time, as long as thermal is built as a module. WARNING: On some systems, disabling ACPI thermal support will cause the system to run hotter and reduce the lifetime of the hardware. Signed-off-by: NLen Brown <len.brown@intel.com>
-
The documentation used "thinkpad-acpi" to refer to the directories in sysfs, while it should have been using "thinkpad_acpi". Thanks to Hugh Dickins for the error report. I wish I could just call the module and everything else by the proper name with the "-", instead of using these ugly translations to "_". Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Holger Macht 提交于
Send key=value pair along with the uevent instead of a plain value so that userspace (udev) can handle it like common environment variables. Signed-off-by: NHolger Macht <hmacht@suse.de> Acked-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com> Cc: Stephan Berberig <s.berberig@arcor.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLen Brown <len.brown@intel.com>
-
由 Stephan Berberig 提交于
There must not be a new-line character in the uevent. Otherwise, udev gets confused. Thanks to Kay Sievers for pointing it out. Signed-off-by: NStephan Berberig <s.berberig@arcor.de> Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NLen Brown <len.brown@intel.com>
-
git://git390.osdl.marist.edu/pub/scm/linux-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: [S390] monwriter: Serialization bug for multithreaded applications. [S390] vmur: diag14 only works with buffers below 2GB [S390] vmur: add "top of queue" sanity check for reader open [S390] vmur: reject open on z/VM reader files with status HOLD [S390] vmur: use DECLARE_COMPLETION_ONSTACK to keep lockdep happy [S390] vmur: allocate single record buffers instead of one big data buffer [S390] remove DEFAULT_MIGRATION_COST [S390] qdio: make sure data structures are correctly aligned. [S390] hypfs: implement show_options [S390] cio: avoid memory leak on error in css_alloc_subchannel().
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc由 Linus Torvalds 提交于
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix size check for hugetlbfs [POWERPC] Fix initialization and usage of dma_mask [POWERPC] Fix more section mismatches in head_64.S [POWERPC] Revert "[POWERPC] Add 'mdio' to bus scan id list for platforms with QE UEC" [POWERPC] PS3: Update ps3_defconfig [POWERPC] PS3: Remove text saying PS3 support is incomplete [POWERPC] PS3: Fix storage probe logic [POWERPC] cell: Move SPU affinity init to spu_management_of_ops [POWERPC] Fix potential duplicate entry in SLB shadow buffer
-
git://lost.foo-projects.org/~dwillia2/git/iop由 Linus Torvalds 提交于
* 'async-tx-fixes-for-linus' of git://lost.foo-projects.org/~dwillia2/git/iop: async_tx: update MAINTAINERS for async_tx and iop-adma
-
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2由 Linus Torvalds 提交于
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: ocfs2: set non-default s_time_gran during mount ocfs2: Retry sendpage() if it returns EAGAIN ocfs2: Fix rename/extend race [2.6 patch] ocfs2_insert_extent(): remove dead code ocfs2: Fix max offset calculations ocfs2: check ia_size limits in setattr ocfs2: Fix some casting errors related to file writes ocfs2: use s_maxbytes directly in ocfs2_change_file_space() ocfs2: Restrict inode changes in ocfs2_update_inode_atime()
-
git://git.kernel.dk/linux-2.6-block由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: BLOCK: Hide the contents of linux/bio.h if CONFIG_BLOCK=n sysace: HDIO_GETGEO has it's own method for ages drivers/block/cpqarray.c: better error handling and kmalloc + memset conversion to k[cz]alloc drivers/block/cciss.c: kmalloc + memset conversion to kzalloc Clean up duplicate includes in drivers/block/ Fix remap handling by blktrace [PATCH] remove mm/filemap.c:file_send_actor()
-
git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched: sched debug: dont print kernel address in /proc/sched_debug sched: fix typo in the FAIR_GROUP_SCHED branch sched: improve rq-clock overflow logic
-
由 Chuck Ebbert 提交于
The new percpu code has apparently broken the doublefault handler when CONFIG_DEBUG_SPINLOCK is set. Doublefault is handled by a hardware task, making the check SPIN_BUG_ON(lock->owner == current, lock, "recursion"); fault because it uses the FS register to access the percpu data for current, and that register is zero in the new TSS. (The trace I saw was on 2.6.20 where it was GS, but it looks like this will still happen with FS on 2.6.22.) Initializing FS in the doublefault_tss should fix it. AK: Also fix broken ptr_ok() and turn printks into KERN_EMERG AK: And add a PANIC prefix to make clear the system will hang AK: (e.g. x86-64 will recover) Signed-off-by: NChuck Ebbert <cebbert@redhat.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
Fix WARNING: vmlinux.o(.text+0x183): Section mismatch: reference to .init.text:start_kernel (between 'is386' and 'check_x87') Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Pete Zaitcev 提交于
Create arch/x86_64/vdso/.gitignore and put vdso.lds into it. Signed-off-by: NPete Zaitcev <zaitcev@redhat.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
Some people writing boot loaders seem to falsely belief the 32bit zero page is a stable interface for out of tree code like the real mode boot protocol. Add a comment clarifying that is not true. Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
The Averatec 2370 and some other Turion laptop BIOS seems to program the ENABLE_C1E MSR inconsistently between cores. This confuses the lapic use heuristics because when C1E is enabled anywhere it seems to affect the complete chip. Use a global flag instead of a per cpu flag to handle this. If any CPU has C1E enabled disabled lapic use. Thanks to Cal Peake for debugging. Cc: tglx@linutronix.de Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Adrian Bunk 提交于
It's CONFIG_X86_MCE, not CONFIG_MCE. Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Zachary Amsden 提交于
VT is very picky about when it can enter execution. Get all segments setup and get LDT and TR into valid state to allow VT execution under VMware and KVM (untested). This makes the boot decompression run under VT, which makes it several orders of magnitude faster on 64-bit Intel hardware. Before, I was seeing times up to a minute or more to decompress a 1.3MB kernel on a very fast box. Signed-off-by: NZachary Amsden <zach@vmware.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
Commit 19d36ccd "x86: Fix alternatives and kprobes to remap write-protected kernel text" uses code which is being patched for patching. In particular, paravirt_ops does patching in two stages: first it calls paravirt_ops.patch, then it fills any remaining instructions with nop_out(). nop_out calls text_poke() which calls lookup_address() which calls pgd_val() (aka paravirt_ops.pgd_val): that call site is one of the places we patch. If we always do patching as one single call to text_poke(), we only need make sure we're not patching the memcpy in text_poke itself. This means the prototype to paravirt_ops.patch needs to change, to marshal the new code into a buffer rather than patching in place as it does now. It also means all patching goes through text_poke(), which is known to be safe (apply_alternatives is also changed to make a single patch). AK: fix compilation on x86-64 (bad rusty!) AK: fix boot on x86-64 (sigh) AK: merged with other patches Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
It turns out CLFLUSH support is still not complete; we flush the wrong pages. Again disable it for the release. Noticed by Jan Beulich who then also noticed a stupid typo later. Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andi Kleen 提交于
gcc currently doesn't support attributes on types, so we can't use it function pointers. This avoids some warnings on a gcc 4.3 build. Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
Current code assumed that devices were directly connected to a Calgary bridge, as it tried to get the iommu table directly from the parent bus controller. When we have another bridge between the Calgary/CalIOC2 bridge and the device we should look upwards until we get to the top (Calgary/CalIOC2 bridge), where the iommu table resides. Signed-off-by: NMurillo Fernandes Bernardes <mfb@br.ibm.com> Signed-off-by: NMuli Ben-Yehuda <muli@il.ibm.com> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 dean gaudet 提交于
Some broken devices have been discovered to require %al/%ax/%eax registers for MMIO config space accesses. Modify mmconfig.c to use these registers explicitly (rather than modify the global readb/writeb/etc inlines). AK: also changed i386 to always use eax AK: moved change to extended space probing to different patch AK: reworked with inlines according to Linus' requirements. AK: improve comments. Signed-off-by: Ndean gaudet <dean@arctic.org> Signed-off-by: NAndi Kleen <ak@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Greg Ungerer 提交于
There are some parts of include/asm-generic/pgtable.h that are relevant to the non-mmu architectures. To make it easier to include this from them I would like to ifdef the relevant parts. Without this there is a handful of functions that are referenced in here that are not defined on many non-mmu architectures. They could be defined out of course, as an alternative approach. Cc: David Howells <dhowells@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Muli Ben-Yehuda 提交于
This patch finishes the i386 and x86-64 ->sysdata conversion and hopefully also fixes Riku's and Andy's observed bugs. It is based on Yinghai Lu's and Andy Whitcroft's patches (thanks!) with some changes: - introduce pci_scan_bus_with_sysdata() and use it instead of pci_scan_bus() where appropriate. pci_scan_bus_with_sysdata() will allocate the sysdata structure and then call pci_scan_bus(). - always allocate pci_sysdata dynamically. The whole point of this sysdata work is to make it easy to do root-bus specific things (e.g., support PCI domains and IOMMU's). I dislike using a default struct pci_sysdata in some places and a dynamically allocated pci_sysdata elsewhere - the potential for someone indavertantly changing the default structure is too high. - this patch only makes the minimal changes necessary, i.e., the NUMA node is always initialized to -1. Patches to do the right thing with regards to the NUMA node can build on top of this (either add a 'node' parameter to pci_scan_bus_with_sysdata() or just update the node when it becomes known). The patch was compile tested with various configurations (e.g., NUMAQ, VISWS) and run-time tested on i386 and x86-64. Unfortunately none of my machines exhibited the bugs so caveat emptor. Andy, could you please see if this fixes the NUMA issues you've seen? Riku, does this fix "pci=noacpi" on your laptop? Signed-off-by: NMuli Ben-Yehuda <muli@il.ibm.com> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Andi Kleen <ak@suse.de> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: <riku.seppala@kymp.net> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Stephen Hemminger 提交于
Minor docbook error since argument name in comment doesn't match function Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jay Estabrook 提交于
This code corrects the usage of the request_irq() routine. Signed-off-by: NJay Estabrook <jay.estabrook@hp.com> Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Richard Henderson <rth@twiddle.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jes Sorensen 提交于
Files using bits from paravirt.h should explicitly include it rather than relying on it being pulled in by something else. Signed-off-by: NJes Sorensen <jes@sgi.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Peter Chubb 提交于
gcc-4.2 is a lot more picky about its symbol handling. EXPORT_SYMBOL no longer works on symbols that are undefined or defined with static scope. For example, with CONFIG_PROFILE off, I see: kernel/profile.c:206: error: __ksymtab_profile_event_unregister causes a section type conflict kernel/profile.c:205: error: __ksymtab_profile_event_register causes a section type conflict This patch moves the EXPORTs inside the #ifdef CONFIG_PROFILE, so we only try to export symbols that are defined. Also, in kernel/kprobes.c there's an EXPORT_SYMBOL_GPL() for jprobes_return, which if CONFIG_JPROBES is undefined is a static inline and gives the same error. And in drivers/acpi/resources/rsxface.c, there's an ACPI_EXPORT_SYMBOPL() for a static symbol. If it's static, it's not accessible from outside the compilation unit, so should bot be exported. These three changes allow building a zx1_defconfig kernel with gcc 4.2 on IA64. [akpm@linux-foundation.org: export jpobe_return properly] Signed-off-by: NPeter Chubb <peterc@gelato.unsw.edu.au> Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Len Brown <lenb@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Miao Xie 提交于
I find a function(clockevents_unregister_notifier) which is not called by anything in tree. Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com> Acked-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Brownell 提交于
Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer without a cast" reported on SH ... most architectures use macros in that test, SH uses inlined functions. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-