Impact: drop unnecessary code

Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request.  Every field is
guaranteed to be always valid.  Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: NTejun Heo <tj@kernel.org>

Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.

Since there were no PIO5 capable hard drives produced and one would also need
66 MHz IDE clock to actually get the difference WRT the address setup timings
programmed, I decided to simply replace the old non-standard PIO mode 5 timings
with the CFA specified ones.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stf_xl@wp.pl
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE code assumed for years that the bit 1 of the identify data word 53 also
covers the validity of the SW/MW DMA information in words 62 and 63, but it has
always covered only words 64 thru 70, with words 62 and 63 being defined in the
original ATA spec, not in ATA-2...

This fix however should only concern *very* old hard disks and rather old CF
cards...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_map_sg() calls out from ide_build_sglist()
  to ide_dma_prepare().

* Pass command to ide_destroy_dmatable().

* Rename ide_build_sglist() to ide_dma_map_sg()
  and ide_destroy_dmatable() to ide_dma_unmap_sg().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Set/clear drive->waiting_for_dma flag in the core code
instead of in ->dma_setup and ->dma_end methods.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_map_sg() call from ->dma_setup implementations and
ide_destroy_dmatable() one from *_build_dmatable() to ide_dma_prepare().

There should be no functional changes caused by this patch.

Sergei:
Removed 'use_pio_instead' labels and replaced 'goto' with 'return 0' --
that required no changes to the follow-up patches...
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add (an optional) ->dma_check method for checking if DMA can be
  used for a given command and fail DMA setup in ide_dma_prepare()
  if necessary.

* Convert alim15x3 and trm290 host drivers to use ->dma_check.

* Rename ali15x3_dma_setup() to ali_dma_check() while at it.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_dma_prepare() helper.

* Convert ide_issue_pc() and do_rw_taskfile() to use it.

* Make ide_build_sglist() static.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_destroy_dmatable() call out from ->dma_end method to
{ide_pc,cdrom_newpc,ide_dma}_intr(), ide_dma_timeout_retry()
and sgiioc4_resetproc().

This causes minor/safe behavior changes w.r.t.:
* cmd64x.c::cmd64{8,x}_dma_end()
* cs5536.c::cs5536_dma_end()
* icside.c::icside_dma_end()
* it821x.c::it821x_dma_end()
* scc_pata.c::__scc_dma_end()
* sl82c105.c::sl82c105_dma_end()
* tx4939ide.c::tx4939ide_dma_end()

v2:
* Fix build for CONFIG_BLK_DEV_IDEDMA=n (reported by Randy Dunlap).

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide_dma_timeout() is only used by ide_dma_timeout_retry()
inline it there.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All custom ->dma_timeout implementations call the generic one thus it is
possible to have only an optional method for resetting DMA engine instead:

* Add ->dma_clear method and convert hpt366, pdc202xx_old and sl82c105
  host drivers to use it.

* Always use ide_dma_timeout() in ide_dma_timeout_retry() and remove
 ->dma_timeout method.

* Make ide_dma_timeout() static.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename dma_timer_expiry() to ide_dma_sff_timer_expiry() and export it.

* Add ->dma_timer_expiry method and use it to set hwif->expiry for
  ATA_PROT_DMA protocol in do_rw_taskfile().

* Initialize ->dma_timer_expiry to ide_dma_sff_timer_expiry() for SFF hosts.

* Move setting hwif->expiry from ide_execute_command() to its users and drop
  'expiry' argument.

* Use ide_execute_command() instead of ->dma_exec_cmd in do_rw_taskfile().

* Remove ->dma_exec_cmd method and its implementations.

* Unexport ide_execute_command() and ide_dma_intr().

v2:
* Fix CONFIG_BLK_DEV_IDEDMA=n build (noticed by Randy Dunlap).

* Fix *dma_expiry naming (suggested by Sergei Shtylyov).

There should be no functional changes caused by this patch.

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Set IDE_TFLAG_WRITE flag and ->rq also for ATA_CMD_PACKET
  commands.

* Pass command to ->dma_setup method and update all its
  implementations accordingly.

* Pass command instead of request to ide_build_sglist(),
  *_build_dmatable() and ide_map_sg().

While at it:

* Fix scc_dma_setup() documentation + use ATA_DMA_WR define.

* Rename sgiioc4_build_dma_table() to sgiioc4_build_dmatable(),
  change return value type to 'int' and drop unused 'ddir'
  argument.

* Do some minor cleanups in [tx4939]ide_dma_setup().

There should be no functional changes caused by this patch.
Acked-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_rq_bytes() helper.

* Add blk_noretry_request() quirk to ide_complete_rq() (currently only fs
  requests can be marked as "noretry" so there is no change in behavior).

* Switch current ide_end_request() users to use ide_complete_rq().

  [ No need to check for rq->nr_sectors == 0 in {ide_dma,task_pio}_intr(),
    nsectors == 0 in cdrom_end_request() and err == 0 in ide_do_devset(). ]

* Remove no longer needed ide_end_request().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_end_request() call out from ide_finish_cmd() to its users.

* Use ide_finish_cmd() in task_no_data_intr().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move command related fields from ide_hwif_t to struct ide_cmd.

* Make ide_init_sg_cmd() take command and sectors number as arguments.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_FS taskfile flag and set it for REQ_TYPE_FS requests.

* Convert ->{in,out}put_data methods to take command instead of request
  as an argument.  Then convert pre_task_out_intr(), task_end_request(),
  task_error(), task_in_unexpected(), ide_pio_sector(), ide_pio_multi()
  and ide_pio_datablock() in similar way.

* Rename task_end_request() to ide_finish_cmd().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Re-map sg table if needed in ide_build_sglist().

* Move ide_build_sglist() call from ->dma_setup to its users.

* Un-export ide_build_sglist().

v2:
* Build fix for CONFIG_BLK_DEV_IDEDMA=n (noticed by Randy Dunlap).

There should be no functional changes caused by this patch.

Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_dma_timeout_retry() to ide-dma.c and add static inline
version for CONFIG_BLK_DEV_IDEDMA=n.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).

The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Merge ide_hwgroup_t with ide_hwif_t.

* Cleanup init_irq() accordingly, then remove no longer needed
  ide_remove_port_from_hwgroup() and ide_ports[].

* Remove now unused HWGROUP() macro.

While at it:

* ide_dump_ata_error() fixups

v2:
* Fix ->quirk_list check in do_ide_request()
  (s/hwif->cur_dev/prev_port->cur_dev).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

- s/HWIF(drive)/drive->hwif/
- s/HWGROUP(drive)/[drive->]hwif->hwgroup/
- fixup error messages in ide_dma_intr() & dma_timer_expiry()
- fix checkpatch.pl errors/warnings
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

- use for_each_sg()
- move printing 'DMA table too small' message below use_pio_instead label
- merge '64KB bug' comment with function documentation
- fix intendation

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Follow-up to commit 5c05ff68
("ide: switch to DMA-mapping API"):

* pci_{alloc,free}_consistent() -> dma_{alloc,free}_coherent()
  in ide_{allocate,release}_dma_engine().

* Add ->prd_max_nents and ->prd_ent_size fields to ide_hwif_t
  (+ set default values in ide_allocate_dma_engine()).

* Make ide_{allocate,release}_dma_engine() available also
  for CONFIG_BLK_DEV_IDEDMA_SFF=n.  Then convert au1xxx-ide.c,
  scc_pata.c and sgiioc4.c to use them.

* Add missing ->init_dma method to scc_pata.

This patch also fixes:
- ->dmatable_cpu leak for au1xxx-ide
- too early realease of ->dmatable_cpu for scc_pata
- wrong amount of ->dmatable_cpu memory being freed for sgiioc4

While at it:
- remove superfluous ->dma_base check from ide_unregister()
- return -ENOMEM on error in ide_release_dma_engine()
- beautify error message in ide_release_dma_engine()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make ide_dma_timeout() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
and convert {ics,au1xxx-}ide.c to use it.

While at it:
- dump ATA Status register content on error
- use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make ide_dma_lost_irq() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
and convert {ics,au1xxx-}ide.c to use it.

While at it:
- use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Call ide_port_init_devices() in ide_host_register()
  also if 'struct ide_port_info *d' is not available.

* Init drive->dn in ide_port_init_devices() instead of
  ide_probe_port() so it is valid also in ->init_dev.

* Pass device number to ide_dev_apply_params().

* Use 'drive->dn & 1' instead of drive->select.b.unit.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.

While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* ERR_STAT   -> ATA_ERR
* INDEX_STAT -> ATA_IDX
* ECC_STAT   -> ATA_CORR
* DRQ_STAT   -> ATA_DRQ
* SEEK_STAT  -> ATA_DSC
* WRERR_STAT -> ATA_DF
* READY_STAT -> ATA_DRDY
* BUSY_STAT  -> ATA_BUSY

* MARK_ERR   -> ATA_AMNF
* TRK0_ERR   -> ATA_TRK0NF
* ABRT_ERR   -> ATA_ABORTED
* MCR_ERR    -> ATA_MCR
* ID_ERR     -> ATA_IDNF
* MC_ERR     -> ATA_MC
* ECC_ERR    -> ATA_UNC
* ICRC_ERR   -> ATA_ICRC

* BBD_ERR    -> ATA_BBK

Also:

* ILI_ERR    -> ATAPI_ILI
* EOM_ERR    -> ATAPI_EOM
* LFS_ERR    -> ATAPI_LFS

* CD         -> ATAPI_COD
* IO         -> ATAPI_IO
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out HDIO_[OBSOLETE,GET]_IDENTITY ioctls handling
  to ide_get_identity_ioctl().

* Use temporary buffer in ide_get_identity_ioctl() instead
  of accessing drive->id directly.

* Add ide_id_to_hd_driveid() inline to convert raw id into
  struct hd_driveid format (needed on big-endian).

* Use ide_id_to_hd_driveid() in ide_get_identity_ioctl(),
  cleanup ide_fix_driveid() and switch ide to use use raw id.

* Remove no longer needed drive->driveid.

  This leaves us with 3 users of struct hd_driveid in tree:
  - arch/um/drivers/ubd_kern.c
  - drivers/block/xsysace.c
  - drivers/usb/storage/isd200.c

While at it:

* Use ata_id_u{32,64}() and ata_id_has_{dma,lba,iordy}() macros.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make drive->id an unnamed union so id can be accessed either by using
'u16 *id' or 'struct hd_driveid *driveid'.  Then convert all existing
drive->id users accordingly (using 'u16 *id' when possible).

This is an intermediate step to make ide 'struct hd_driveid'-free.

While at it:

- Add missing KERN_CONTs in it821x.c.

- Use ATA_ID_WORDS and ATA_ID_*_LEN defines.

- Remove unnecessary checks for drive->id.

- s/drive_table/table/ in ide_in_drive_list().

- Cleanup ide_config_drive_speed() a bit.

- s/drive1/dev1/ & s/drive0/dev0/ in ide_undecoded_slave().

v2:
Fix typo in drivers/ide/ppc/pmac.c. (From Stephen Rothwell)

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check.  So, we must never try
to "split" the PRD for TRM290.

This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

id->tDMA is of 'unsigned char' type so endianness is already
correct and calling le16_to_cpu() is wrong.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add struct ide_tp_ops for transport methods.

* Add 'const struct ide_tp_ops *tp_ops' to struct ide_port_info
  and ide_hwif_t.

* Set the default hwif->tp_ops in ide_init_port_data().

* Set host driver specific hwif->tp_ops in ide_init_port().

* Export ide_exec_command(), ide_read_status(), ide_read_altstatus(),
  ide_read_sff_dma_status(), ide_set_irq(), ide_tf_{load,read}()
  and ata_{in,out}put_data().

* Convert host drivers and core code to use struct ide_tp_ops.

* Remove no longer needed default_hwif_transport().

* Cleanup ide_hwif_t from methods that are now in struct ide_tp_ops.

While at it:

* Use struct ide_port_info in falconide.c and q40ide.c.

* Rename ata_{in,out}put_data() to ide_{in,out}put_data().

v2:

* Fix missing convertion in ns87415.c.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>