Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix build error for il_pm_ops if CONFIG_PM is set
but CONFIG_PM_SLEEP is not set.

ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined!
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This false leak indication is avoided with a no-leak annotation to kmemleak.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to a typo, the current code copies only sizeof(cmd->channels_2)
bytes, which is smaller than the correct sizeof(cmd->channels_5)
size, resulting in a partial scan (some channels are skipped).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The minimum firmware version required for singlerole after recent
driver changes is 6/7.3.10.0.133.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected.  The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: NLevi Pearson <levipearson@gmail.com>
Reported-by: NMichael Scott <hashcode0f@gmail.com>
Cc: stable@kernel.org # 3.9+
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver rtl8192cu can connect to WPA2 networks, but fails for any other
encryption method. The cause is a failure to set the rate control data
blocks. These changes fix https://bugzilla.redhat.com/show_bug.cgi?id=952793
and https://bugzilla.redhat.com/show_bug.cgi?id=761525.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When reading the contents of '/sys/kernel/debug/mwifiex/p2p0/info',
the following panic occurs:

$ cat /sys/kernel/debug/mwifiex/p2p0/info
Unable to handle kernel paging request at virtual address 74706164
pgd = de530000
[74706164] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: phy_twl4030_usb omap2430 musb_hdrc mwifiex_sdio mwifiex
CPU: 0 PID: 1635 Comm: cat Not tainted 3.10.0-rc1-00010-g1268390 #1
task: de16b6c0 ti: de048000 task.ti: de048000
PC is at strnlen+0xc/0x4c
LR is at string+0x3c/0xf8
pc : [<c02c123c>]    lr : [<c02c2d1c>]    psr: a0000013
sp : de049e10  ip : c06efba0  fp : de6d2092
r10: bf01a260  r9 : ffffffff  r8 : 74706164
r7 : 0000ffff  r6 : ffffffff  r5 : de6d209c  r4 : 00000000
r3 : ff0a0004  r2 : 74706164  r1 : ffffffff  r0 : 74706164
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 9e530019  DAC: 00000015
Process cat (pid: 1635, stack limit = 0xde048240)
Stack: (0xde049e10 to 0xde04a000)
9e00:                                     de6d2092 00000002 bf01a25e de6d209c
9e20: de049e80 c02c438c 0000000a ff0a0004 ffffffff 00000000 00000000 de049e48
9e40: 00000000 2192df6d ff0a0004 ffffffff 00000000 de6d2092 de049ef8 bef3cc00
9e60: de6b0000 dc358000 de6d2000 00000000 00000003 c02c45a4 bf01790c bf01a254
9e80: 74706164 bf018698 00000000 de59c3c0 de048000 de049f80 00001000 bef3cc00
9ea0: 00000008 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9ee0: 00000000 00000000 00000000 00000001 00000000 00000000 6669776d 20786569
9f00: 20302e31 2e343128 392e3636 3231702e 00202933 00000000 00000003 c0294898
9f20: 00000000 00000000 00000000 00000000 de59c3c0 c0107c04 de554000 de59c3c0
9f40: 00001000 bef3cc00 de049f80 bef3cc00 de049f80 00000000 00000003 c0108a00
9f60: de048000 de59c3c0 00000000 00000000 de59c3c0 00001000 bef3cc00 c0108b60
9f80: 00000000 00000000 00001000 bef3cc00 00000003 00000003 c0014128 de048000
9fa0: 00000000 c0013f80 00001000 bef3cc00 00000003 bef3cc00 00001000 00000000
9fc0: 00001000 bef3cc00 00000003 00000003 00000001 00000001 00000001 00000003
9fe0: 00000000 bef3cbdc 00011984 b6f1127c 60000010 00000003 18dbdd2c 7f7bfffd
[<c02c123c>] (strnlen+0xc/0x4c) from [<c02c2d1c>] (string+0x3c/0xf8)
[<c02c2d1c>] (string+0x3c/0xf8) from [<c02c438c>] (vsnprintf+0x1e8/0x3e8)
[<c02c438c>] (vsnprintf+0x1e8/0x3e8) from [<c02c45a4>] (sprintf+0x18/0x24)
[<c02c45a4>] (sprintf+0x18/0x24) from [<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex])
[<bf01790c>] (mwifiex_info_read+0xfc/0x3e8 [mwifiex]) from [<c0108a00>] (vfs_read+0xb0/0x144)
[<c0108a00>] (vfs_read+0xb0/0x144) from [<c0108b60>] (SyS_read+0x44/0x70)
[<c0108b60>] (SyS_read+0x44/0x70) from [<c0013f80>] (ret_fast_syscall+0x0/0x30)
Code: e12fff1e e3510000 e1a02000 0a00000d (e5d03000)
---[ end trace ca98273dc605a04f ]---

The panic is caused by the mwifiex_info_read() routine assuming that
there can only be four modes (0-3) which is an invalid assumption.
For example, when testing P2P, the mode is '8' (P2P_CLIENT) so the
code accesses data beyond the bounds of the bss_modes[] array which
causes the panic.  Fix this by updating bss_modes[] to support the
current list of modes and adding a check to prevent the out-of-bounds
access from occuring in the future when more modes are added.
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The register offsets have been changed in SD8897 and newer chips.
Define a new btmrvl_sdio_card_reg map for SD88xx.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LE-only controllers do not support extended features so any kind of host
feature bit checks do not make sense for them. This patch fixes code
used for both single-mode (LE-only) and dual-mode (BR/EDR/LE) to use the
HCI_LE_ENABLED flag instead of the "Host LE supported" feature bit for
LE support tests.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accessing the OTP memory on AR9950 causes a data bus
like this:

  Data bus error, epc == 801f7774, ra == 801f7774
  Oops[#1]:
  CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
  task: 87c28000 ti: 87c22000 task.ti: 87c22000
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 80320a68 00000000 7c7c7c3c
  $16   : 87cd8010 00015f18 00000007 00000000
  $20   : 00000064 00000004 87c23c7c 8035210c
  $24   : 00000000 801f3674
  $28   : 87c22000 87c23b48 00000001 801f7774
  Hi    : 00000000
  Lo    : 00000064
  epc   : 801f7774 ath9k_hw_wait+0x58/0xb0
      Not tainted
  ra    : 801f7774 ath9k_hw_wait+0x58/0xb0
  Status: 1000cc03 KERNEL EXL IE
  Cause : 4080801c
  PrId  : 00019750 (MIPS 74Kc)
  Modules linked in:
  Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
  Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
          00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
          000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
          00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
          87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
          ...
  Call Trace:
  [<801f7774>] ath9k_hw_wait+0x58/0xb0
  [<80210c7c>] ar9300_otp_read_word+0x80/0xd4
  [<80210d24>] ar9300_read_otp+0x54/0xb0
  [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
  [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
  [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
  [<801f96d0>] ath9k_hw_init+0x7ec/0x96c
  [<801e65ec>] ath9k_init_device+0x340/0x758
  [<801f35d0>] ath_ahb_probe+0x21c/0x2c0
  [<801c041c>] driver_probe_device+0xc0/0x1e4
  [<801c05ac>] __driver_attach+0x6c/0xa4
  [<801bea08>] bus_for_each_dev+0x64/0xa8
  [<801bfa40>] bus_add_driver+0xcc/0x24c
  [<801c0954>] driver_register+0xbc/0x17c
  [<803f8fc0>] ath9k_init+0x5c/0x88
  [<800608fc>] do_one_initcall+0xec/0x1a0
  [<803e6a68>] kernel_init_freeable+0x13c/0x200
  [<80309cdc>] kernel_init+0x1c/0xe4
  [<80062450>] ret_from_kernel_thread+0x10/0x18

On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.

Cc: stable@vger.kernel.org  # 3.6+
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ARP offloading should only be used in STA or P2P client mode. It
is currently configured once at init. When being configured for AP
ARP offloading should be turned off and when AP mode is left it can
be turned back on.

Cc: stable@vger.kernel.org
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In 63b77bf4

	iwlwifi: dvm: don't send zeroed LQ cmd

I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341

Cc: stable@vger.kernel.org
Reported-by: NHinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When changing the MAC address of a single vif mac80211 will check if
the new address fits into the address mask specified by the driver.
This only needs to be done when using multiple BSSIDs. Hence, check
the new address only against all other vifs.

Also fix the MAC address assignment on new interfaces if the user
changed the address of a vif such that perm_addr is not covered by
addr_mask anymore.

Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=57371Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Reported-by: NAlessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Bruno Randolf <br1@thinktube.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since Eric's commit efe117ab ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.

Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not subtract spur power from noise floor on this chip, as it can lead
to packet loss and other connectivity issues.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.

To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.

For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.

For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: NIlan Peer <ilan.peer@intel.com>
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.

Cc: stable@vger.kernel.org
Reported-by: NYanBo <dreamfly281@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There was an extra ';' character added to the end of the if statement
which means that it always prints that the /proc entry wasn't created
even though it was.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Waiting for all subframes of an existing aggregation session to drain
before allowing mac80211 to start a new one is fragile and deadlocks
caused by this behavior have been observed.

Since mac80211 has proper synchronization for aggregation session
start/stop handling, a better approach to session handling is to simply
allow mac80211 to start a new session at any time. This requires
changing the code to discard any packets outside of the BlockAck window
in the A-MPDU software retry code.

This patch implements the above and also simplifies the code.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"Merge tag 'nfc-fixes-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes

This is the first batch of NFC fixes for 3.10, and it contains:

- 3 fixes for the NFC MEI support:
	* We now depend on the correct Kconfig symbol.
	* We register an MEI event callback whenever we enable an NFC device,
	  otherwise we fail to read anything after an enable/disable cycle.
	* We only disable an MEI device from its disable mey_phy_ops,
	  preventing useless consecutive disable calls.

- An NFC Makefile cleanup, as I forgot to remove a commented out line when
  moving the LLCP code to the NFC top level directory."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling and disabling device is exclusively handled by the mei_phy_ops.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The callback registration starts a waiting read, so it needs to be fired
everytime the device is enabled. Otherwise following writes will never get
an answer back.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

INTEL_MEI_BUS_NFC never made it upstream, so make it depend on INTEL_MEI.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Kconfig symbol NFC_LLCP was removed in commit 30cc4587 ("NFC: Move
LLCP code to the NFC top level diirectory"). But the reference to its
macro in this Makefile was only commented out. Remove it now.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

After a tx attempt, an A-MPDU subframe can still have fi->retries at 0
(if the retry count wasn't incremented due to powersave).
In that case it is still tracked as part of the block ack window, so
when draining the tid queue, its sequence number needs to be cleared
from the pending frame bitmap.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>