When computing the full size of the device, we need to cast
sdkp->capacity before shifting, since in some configurations sector_t
can be a 32-bit number.

Also, change ffz(~x) to the more idiomatic ilog2(x).
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We would hang forever when passing a zero to string_get_size().
Furthermore, string_get_size() would produce decimals on a value small
enough to be exact.  Finally, a few formatting issues are inconsistent
with standard SI style guidelines.

- If the value is less than the divisor, skip the entire rounding
  step.  This prints out all small values including zero as integers,
  without decimals.
- Add a space between the value and the symbol for the unit,
  consistent with standard SI practice.
- Lower case k in kB since we are talking about powers of 10.
- Finally, change "int" to "unsigned int" in one place to shut up a
  gcc warning when compiling the code out-of-kernel for testing.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The pattern !E && !E->fld is nonsensical.  The patch below updates this
according to the assumption that && should be ||.  But perhaps another
solution was intended.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@disable and_comm@
expression E;
identifier fld;
@@

- !E && !E->fld
+ !E || !E->fld
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-By: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch (as1138) removes from sd.c some old code for switching from
10-byte commands to 6-byte commands.  This code is redundant -- the
switching for READ and WRITE is already handled in
scsi_io_completion() and the switching for MODE SENSE is already
handled in scsi_mode_sense().  (There is no comparable switch for MODE
SELECT, but I doubt one is needed.)

Furthermore the other handlers do a better job; they check for
appropriate ASC and ASCQ values before blindly switching the size.
The code in sd.c is known to cause problems with some devices by
switching when it shouldn't.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Since the commit 50bed2e2 (sg: disable
interrupts inside sg_copy_buffer), no need to disable interrupts
before calling scsi_sg_copy_from_buffer. So we can simplify
twa_scsiop_execute_scsi_complete() a bit, which disables interrupts
just for scsi_sg_copy_from_buffer.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NAdam Radford <linuxraid@amcc.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Since the commit 50bed2e2 (sg: disable
interrupts inside sg_copy_buffer), no need to disable interrupts
before calling scsi_sg_copy_from_buffer. So we can simplify
tw_transfer_internal, which disables interrupts just for
scsi_sg_copy_from_buffer.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>\
Acked-by: NAdam Radford <linuxraid@amcc.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Fix kernel-doc warning: the function short description must be on one
line and the previous comment is not kernel-doc but it was confusing
scripts/kernel-doc.

Warning(lin2627-g3-kdocfixes//drivers/scsi/scsi_netlink.c:221): No description found for parameter 'skb'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The current handling of NO_SENSE check condition is the same as
RECOVERED_ERROR, and assumes that in both cases, the I/O was fully
transferred.

We have seen cases of arrays returning with NO_SENSE (no error), but
the I/O was not completely transferred, thus residual set.  Thus,
rather than return good_bytes as the entire transfer, set good_bytes
to 0, so that the midlayer then applies the residual in calculating
the transfer, and for sd, will fail the I/O and fall into a retry
path.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch implements q->lld_busy_fn() for scsi mid layer to export
its busy state for request stacking drivers.

For efficiency, no lock is taken to check the busy state of
shost/starget/sdev, since the returned value is not guaranteed and
may be changed after request stacking drivers call the function,
regardless of taking lock or not.

When scsi can't dispatch I/Os anymore and needs to kill I/Os
(e.g. !sdev), scsi needs to return 'not busy'.
Otherwise, request stacking drivers may hold requests forever.
Signed-off-by: NKiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch refactors the busy checking codes of scsi_device,
Scsi_Host and scsi_target.  There should be no functional change.

This is a preparation for another patch which exports scsi's busy
state to the block layer for request stacking drivers.
Signed-off-by: NKiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Make SPI timeout 10s the same as SAS
Signed-off-by: NBernd Schubert <bs@q-leap.de>
Acked-by: N"Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Take the Diag/Activity-LED of the HBA out of diagnostic mode on PM
resume after successful PM resume from standby and HBA restart, it
remained always on before. If something fails before complete
recovery, it should remain on, since it is a diagnostics LED, reason
for the used higher layer for the clear.

Signed-off-by: thomas.schorpp@gmail.com
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

MHZ not Mhz for SI unit pedants

Closes bug #6422
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

OK to just reuse the outer declaration as it is never used again.
drivers/scsi/aic7xxx/aic79xx_pci.c:340:12: warning: symbol 'devconfig' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_pci.c:299:12: originally declared here

targpcistat is always assigned just before use, remove the inner declaration.
drivers/scsi/aic7xxx/aic79xx_pci.c:486:9: warning: symbol 'targpcistat' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_pci.c:429:9: originally declared here
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Redeclared within different if/else blocks, safe to reuse the
original from beginning of function.
drivers/scsi/aic7xxx/aic79xx_core.c:2475:10: warning: symbol 'scbid' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:2399:10: originally declared here
drivers/scsi/aic7xxx/aic79xx_core.c:2586:10: warning: symbol 'scbid' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:2399:10: originally declared here
drivers/scsi/aic7xxx/aic79xx_core.c:2587:15: warning: symbol 'scb' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:2393:13: originally declared here

Use caminfo for the outer declaration, the redeclared version is
iterating over all initiator/target pairs (devices) which.
drivers/scsi/aic7xxx/aic79xx_core.c:8857:23: warning: symbol 'devinfo' shadows an earlier one
drivers/scsi/aic7xxx/aic79xx_core.c:8711:21: originally declared here

Forward declaration was already marked static, make the definition match.
drivers/scsi/aic7xxx/aic79xx_core.c:3693:1: warning: symbol 'ahd_devlimited_syncrate' was not declared. Should it be static?
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NDenys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Update .reg files, marking unused registers with dont_generate_debug_code.
Comment explains how to use it.
Signed-off-by: NDenys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

aic7xxx still contains ~30kb of dead code if pretty printing of registers
is requested. These patches deal with it.

Size differences:

   text    data     bss     dec     hex filename
DEBUG_ENABLE+PRETTY_PRINT:
 234697    2362    1188  238247   3a2a7 linux-2.6.26-rc8-/drivers/scsi/aic7xxx/built-in.o
 205092    2362    1188  208642   32f02 linux-2.6.26-rc8/drivers/scsi/aic7xxx/built-in.o
NO_DEBUG_ENABLE+PRETTY_PRINT:
 227272    2362    1172  230806   38596 linux-2.6.26-rc8-/drivers/scsi/aic7xxx/built-in.o
 197671    2362    1172  201205   311f5 linux-2.6.26-rc8/drivers/scsi/aic7xxx/built-in.o
DEBUG_ENABLE+NO_PRETTY_PRINT:
 192457    2362    1188  196007   2fda7 linux-2.6.26-rc8-/drivers/scsi/aic7xxx/built-in.o
 192457    2362    1188  196007   2fda7 linux-2.6.26-rc8/drivers/scsi/aic7xxx/built-in.o
NO_DEBUG_ENABLE+NO_PRETTY_PRINT:
 185040    2362    1172  188574   2e09e linux-2.6.26-rc8-/drivers/scsi/aic7xxx/built-in.o
 185040    2362    1172  188574   2e09e linux-2.6.26-rc8/drivers/scsi/aic7xxx/built-in.o

This patch:

Introduce "dont_generate_debug_code" keyword in aicasm parser.
Signed-off-by: NDenys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the path state to be passive when we learn that the controller does
not own the path to the LUN.

This will avoid sending even a single i/o thru the passive path at the
probe time.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

On Tue, 12 Aug 2008 15:08:14 +0200
Giuliano Pochini <pochini@shiny.it> wrote:

> Fujitsu magneto-optical drive, Adaptec 29160 and
> Linux Jay 2.6.26 #7 SMP Sun Aug 10 18:34:22 CEST 2008 ppc 7455, altivec supported PowerMac3,6 GNU/Linux
>
> When I insert a disk and I mount it, scsi_test_unit_ready() is called and
> the do-while loop gets sshdr->sense_key == UNIT_ATTENTION in the first
> cycle and 0 in the second one. So the if below misses the UNIT_ATTENTION
> and sdev->changed = 1 is not executed. At this point bad things can
> happen... I'm not sure how to fix this. Any clue ?

The problem is essentially caused by us eating UNIT_ATTENTION
conditions in scsi_test_unit_ready().  Fix by updating the ->changed
flag when this happens if the media is removable.

[pochini@shiny.it: updates to tidy up patch]
Signed-off-by: NGiuliano Pochini <pochini@shiny.it>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (25 commits)
  staging: at76_usb wireless driver
  Staging: workaround build system bug
  Staging: Lindent sxg.c
  Staging: SLICOSS: Call pci_release_regions at driver exit
  Staging: SLICOSS: Fix remaining type names
  Staging: SLICOSS: Fix warnings due to static usage
  Staging: SLICOSS: lots of checkpatch fixes
  Staging: go7007 v4l fixes
  Staging: Fix gcc warnings in sxg
  Staging: add echo cancelation module
  Staging: add wlan-ng prism2 usb driver
  Staging: add w35und wifi driver
  Staging: USB/IP: add host driver
  Staging: USB/IP: add client driver
  Staging: USB/IP: add common functions needed
  Staging: add the go7007 video driver
  Staging: add me4000 pci data collection driver
  Staging: add me4000 firmware files
  Staging: add sxg network driver
  Staging: add Alacritech slicoss network driver
  ...

Fixed up conflicts due to taint flags changes and MAINTAINERS cleanup in
MAINTAINERS, include/linux/kernel.h and kernel/panic.c.

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (47 commits)
  hwmon: (adm1026) Prevent log spamming
  hwmon: (adm1026) Fix debug messages
  hwmon: (adm1029) Use mask for fan_div value
  hwmon: (adt7470) Add documentation
  hwmon: (ibmaem) Automatically load on IBM systems via DMI
  hwmon: (ibmpex) Automatically load on IBM systems via DMI
  hwmon: (w83781d) Use new style driver binding
  hwmon: (w83781d) Stop abusing struct i2c_client for ISA devices
  hwmon: (w83781d) Make ISA interface depend on CONFIG_ISA
  hwmon: (w83781d) Additional information about AS99127F PWM
  hwmon: (w83781d) Detect alias chips
  hwmon: (w83781d) Refactor beep enable handling
  hwmon: Drop dead links to old National Semiconductor chip datasheets
  hwmon: (w83791d) add support for thermal cruise mode
  hwmon: (w83791d) add pwm_enable support
  hwmon: (w83791d) add manual PWM support
  hwmon: (w83791d) fan 4/5 pins can also be used for gpio
  hwmon: (max1619) Use inline functions instead of macros
  hwmon: (it87) Fix thermal sensor type values
  hwmon: (lm78) Convert to a new-style i2c driver
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Fix debugfs_create_dir's error checking method for sound/soc/
  ALSA: ASoC: Convert playpaq_wm8510 to bulk route registration API
  ALSA: kernel docs: fix sound/core/ kernel-doc
  ALSA: Handle NULL jacks in snd_jack_report()
  ALSA: hda - Fix PCM type of Nvidia HDMI devices

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: remove __generic_unplug_device() from exports
  block: move q->unplug_work initialization
  blktrace: pass zfcp driver data
  blktrace: add support for driver data
  block: fix current kernel-doc warnings
  block: only call ->request_fn when the queue is not stopped
  block: simplify string handling in elv_iosched_store()
  block: fix kernel-doc for blk_alloc_devt()
  block: fix nr_phys_segments miscalculation bug
  block: add partition attribute for partition number
  block: add BIG FAT WARNING to CONFIG_DEBUG_BLOCK_EXT_DEVT
  softirq: Add support for triggering softirq work on softirqs.

* 'for-linus' of git://www.jni.nu/cris:
  CRIS: proper defconfig setup
  [CRIS] Rename boot-linkscripts and fix the path to them.

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (39 commits)
  [SCSI] sd: fix compile failure with CONFIG_BLK_DEV_INTEGRITY=n
  libiscsi: fix locking in iscsi_eh_device_reset
  libiscsi: check reason why we are stopping iscsi session to determine error value
  [SCSI] iscsi_tcp: return a descriptive error value during connection errors
  [SCSI] libiscsi: rename host reset to target reset
  [SCSI] iscsi class: fix endpoint id handling
  [SCSI] libiscsi: Support drivers initiating session removal
  [SCSI] libiscsi: fix data corruption when target has to resend data-in packets
  [SCSI] sd: Switch kernel printing level for DIF messages
  [SCSI] sd: Correctly handle all combinations of DIF and DIX
  [SCSI] sd: Always print actual protection_type
  [SCSI] sd: Issue correct protection operation
  [SCSI] scsi_error: fix target reset handling
  [SCSI] lpfc 8.2.8 v2 : Add statistical reporting control and additional fc vendor events
  [SCSI] lpfc 8.2.8 v2 : Add sysfs control of target queue depth handling
  [SCSI] lpfc 8.2.8 v2 : Revert target busy in favor of transport disrupted
  [SCSI] scsi_dh_alua: remove REQ_NOMERGE
  [SCSI] lpfc 8.2.8 : update driver version to 8.2.8
  [SCSI] lpfc 8.2.8 : Add MSI-X support
  [SCSI] lpfc 8.2.8 : Update driver to use new Host byte error code DID_TRANSPORT_DISRUPTED
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
  ipv4: Add a missing rcu_assign_pointer() in routing cache.
  [netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
  xen-netfront: Avoid unaligned accesses to IP header
  lmc: copy_*_user under spinlock
  [netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA

When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>

* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>

This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: NCorentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add at least the bare minimum of documentation for this chip.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.

[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350

This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>

We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>