- 03 2月, 2009 1 次提交
-
-
由 Roel Kluin 提交于
while (timeout--) { ... } timeout becomes -1 if the loop isn't ended otherwise, not 0. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 1月, 2009 1 次提交
-
-
由 Steve Glendinning 提交于
smsc9420 performs an interrupt signalling test when the interface is brought up. The current code mistakenly sets its test flag to false AFTER enabling the software interrupt source, making failure quite likely. This patch changes the code to set the test flag BEFORE enabling interrupts. I've also removed an smp_wmb because the following spinlock provides an implicit memory barrier. Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 1月, 2009 1 次提交
-
-
由 Stephen Hemminger 提交于
Many drivers lost the ability to set ethernet address accidently during the net_device_ops conversion. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 12月, 2008 1 次提交
-
-
由 Neil Horman 提交于
When the napi api was changed to separate its 1:1 binding to the net_device struct, the netif_rx_[prep|schedule|complete] api failed to remove the now vestigual net_device structure parameter. This patch cleans up that api by properly removing it.. Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 12月, 2008 1 次提交
-
-
由 Steve Glendinning 提交于
These 4 drivers have identical full duplex flow control resolution functions. This patch changes them all to use one common function. The function in question decides whether a device should enable TX and RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this should also be useful for other drivers. Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 12月, 2008 1 次提交
-
-
由 Steve Glendinning 提交于
This patch adds support for SMSC's LAN9420 PCI ethernet controller to ethtool's dump registers (-d) command. This patch is for use with an accompanying ethtool patch, which decodes the register dump. Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 12月, 2008 2 次提交
-
-
由 Steve Glendinning 提交于
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Steve Glendinning 提交于
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 12月, 2008 1 次提交
-
-
由 Steve Glendinning 提交于
This patch adds a driver for the LAN9240 PCI ethernet adapter. Changes since initial submission: - debug msg_level has been changed to use standard definitions - convert to use net_device_ops Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-