Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count.  This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions.  As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed.  This often leads to consecutive hotplug events
without successful probing.

This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.

As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants.  This parameter doesn't get in the way even
when it's too low.  The closest possible limit is applied.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events.  This patch
achieves this by doing the following.

* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
  clear between BEGIN and END.  ering is moved after END.  The split
  of persistent area is to allow hotter items remain at the head.

* ering is explicitly cleared on ata_dev_disable() and when device
  attach succeeds.  So, ering is persistent throug a device's life
  time (unless explicitly cleared of course) and also through periods
  inbetween disablement of an attached device and successful detection
  of the next one.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_dev_disable() is about to be more tightly integrated into EH
logic.  Move it to libata-eh.c.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.

This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_port_detach() first made sure EH saw ATA_PFLAG_UNLOADING and then
assumed EH context belongs to it and performed detach operation
itself.  However, UNLOADING doesn't disable all of EH and this could
lead to problems including triggering WARN_ON()'s in EH path.

This patch makes port detach behave more like other EH actions such
that ata_port_detach() requests EH to detach and waits for completion.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There currently are the following looping constructs.

* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order

Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link.  Instead of adding another one with long name, do the following
cleanup.

* Implement and export ata_link_next() and ata_dev_next() which take
  @mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
  looping mode explicitly.

The following iteration modes are implemented.

* ATA_LITER_EDGE		: loop over edge links
* ATA_LITER_HOST_FIRST		: loop over all links, host link first
* ATA_LITER_PMP_FIRST		: loop over all links, PMP links first

* ATA_DITER_ENABLED		: loop over enabled devices
* ATA_DITER_ENABLED_REVERSE	: loop over enabled devices in reverse order
* ATA_DITER_ALL			: loop over all devices
* ATA_DITER_ALL_REVERSE		: loop over all devices in reverse order

This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ehc->last_reset is used to ensure that resets are not issued too
close to each other.  It's initialized to jiffies minus one minute
on EH entry.  However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.

This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized.  As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.

This problem is spotted and debugged by Shane Huang.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed.  These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.

* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()

While at it, reformat comments in cable_is_40wire().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links.  This patch clears device class to NONE
during post-reset processing if phys link is offline.

As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Slave link action mask is transferred to master link and all the EH
actions are taken by the master link.  ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer.  This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.

Don't set ATA_PFLAG_RECOVERED for slave link actions.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH.  As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.

This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: NMike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Resets make ATAPI devices raise UNIT ATTENTION which fails the next
command.  As resets can happen asynchronously for unrelated reasons,
this sometimes disrupts innocent users.  For example, reading DVD
fails after the system wakes up from suspend or the other device
sharing the channel went through bus error.

Clearing UA has some problems as it might clear UA which the userland
needs to know about.  However, UA after resets can only be about the
reset itself and benefits of clearing it overweights cons.  Missing UA
can only delay failure to one of the following commands anyway.  For
example, timeout while burning is in progress will trigger reset and
reset the device state and probably corrupt the burning run.  Although
the userland application won't get the UA, its pending writes will
fail.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Explanation taken from the comment of ata_slave_link_init().

 In libata, a port contains links and a link contains devices.  There
 is single host link but if a PMP is attached to it, there can be
 multiple fan-out links.  On SATA, there's usually a single device
 connected to a link but PATA and SATA controllers emulating TF based
 interface can have two - master and slave.

 However, there are a few controllers which don't fit into this
 abstraction too well - SATA controllers which emulate TF interface
 with both master and slave devices but also have separate SCR
 register sets for each device.  These controllers need separate links
 for physical link handling (e.g. onlineness, link speed) but should
 be treated like a traditional M/S controller for everything else
 (e.g. command issue, softreset).

 slave_link is libata's way of handling this class of controllers
 without impacting core layer too much.  For anything other than
 physical link handling, the default host link is used for both master
 and slave.  For physical link handling, separate @ap->slave_link is
 used.  All dirty details are implemented inside libata core layer.
 From LLD's POV, the only difference is that prereset, hardreset and
 postreset are called once more for the slave link, so the reset
 sequence looks like the following.

 prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
 softreset(M) -> postreset(M) -> postreset(S)

 Note that softreset is called only for the master.  Softreset resets
 both M/S by definition, so SRST on master should handle both (the
 standard method will work just fine).

As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.

 * ata_is_host_link() updated so that slave_link is considered as host
   link too.

 * iterator extended to iterate over the slave_link when using the
   underbarred version.

 * force param handling updated such that devno 16 is mapped to the
   slave link/device.

 * ata_link_on/offline() updated to return the combined result from
   master and slave link.  ata_phys_link_on/offline() are the direct
   versions.

 * EH autopsy and report are performed separately for master slave
   links.  Reset is udpated to implement the above described reset
   sequence.

Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.

After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

SError belongs to link not port.  Use ata_link_printk() to print it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Update atapi_eh_request_sense() to take @dev, @sense_buf and
@dfl_sense_key instead of taking @qc and extracting information from
it.  This change is to make the function more generic and allow it to
be called from other places.

While at it, make cdb initialization use initializer.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong.  This patch
implements command type based stepped timeouts.  Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.

ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much.  After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.

IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.

This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This doesn't introduce any functional changes.  This is to make reset
timeout table consistent with to-be-added command timeout tables.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back.  However, this 5 second delay is superflous or excessive
in many cases.  For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.

This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.

As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.

While at it, convert explicit rounding up division to DIV_ROUND_UP().

This change speeds up EH in many cases w/o sacrificing robustness.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.

If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen.  It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset().  This had two race
conditions.  1: hotplug could occur after reset but before SError is
cleared and libata won't know about it.  2: hotplug could occur after
all the reset is complete but before the port is thawed.  As all
events are cleared on thaw, the hotplug event would be lost.

Commit ac371987 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.

This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown.  As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.

This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.

Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.

This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().

This makes code simpler and will help removing hotplug event related
races.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset.  This makes no reset case behave better (readiness wait)
and future changes easier.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix mis-reporting of NCQ errors by ensuring that result_tf->flags
is properly initialized in libata-eh.  This allows ata_gen_ata_sense()
to report the failed block number correctly to SCSI after a media error
during NCQ.

This patch may also be a candidate for backporting to earlier kernels.
Without this fix, SCSI will fail I/O on the entire request rather
than just the bad sector.  That can be bad for a request that was
merged from many independent read reads from different tasks.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When no reset method is available, libata currently oopses.  Although
the condition can't happen unless there's a bug in a low level driver,
oopsing isn't the best way to report the error condition.  Complain,
dump stack and fail reset instead.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.

This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.

sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset.  This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some code paths which had been made obsolete by recent reset
simplification were still around.  Kill them.

* ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine
  classification failure.  This is no longer applicable.

* ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE
  regardless of reset result (e.g. -EAGAIN).

* LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link.  While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.

This change simplifies LLDs and helps making PMP support optional.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified.  Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.

Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required".  This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.
Signed-off-by: NTejun Heo <htejun@gmail.com>

If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset.  This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART.  However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.

This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs.  As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset().  sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.

ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.

piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.
Signed-off-by: NTejun Heo <htejun@gmail.com>