- 25 6月, 2009 5 次提交
-
-
由 Ralf Baechle 提交于
This fixes kernel.org bugzilla 13596, see http://bugzilla.kernel.org/show_bug.cgi?id=13596 Reported-by: dvice_null@yahoo.com Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
This fixes kernel.org bugzilla 13595, see http://bugzilla.kernel.org/show_bug.cgi?id=13595 Reported-by: dvice_null@yahoo.com Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
We can't perform any flushes on SMP from swsusp_arch_resume because interrupts are disabled. A cross-CPU flush is unnecessary anyway because all but the local CPU have already been disabled. A local flush is not needed either because we didn't change any mappings. So just delete the code. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Some of the were relying into smp.h being dragged in by another header which of course is fragile. <asm/cpu-info.h> uses smp_processor_id() only in macros and including smp.h there leads to an include loop, so don't change cpu-info.h. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
In the past this file somehow used to be dragged in. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 24 6月, 2009 23 次提交
-
-
由 Mikael Pettersson 提交于
On bootup nvidiafb prints the following on my Apple G5: nvidiafb: CRTC 1appears to have a CRT attached There should be a space between the '1' and the 'appears'. Add it. Signed-off-by: NMikael Pettersson <mikpe@it.uu.se> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Robert P. J. Day 提交于
Fix the incorrect "select" directives by dropping the "CONFIG_" prefixes, and correcting the typo "H8S2768" to "H8S2678". Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca> Acked-by: NYoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Dimitri Sivanich 提交于
After downing/upping a cpu, an attempt to set /proc/sys/vm/percpu_pagelist_fraction results in an oops in percpu_pagelist_fraction_sysctl_handler(). If a processor is downed then we need to set the pageset pointer back to the boot pageset. Updates of the high water marks should not access pagesets of unpopulated zones (those pointer go to the boot pagesets which would be no longer functional if their size would be increased beyond zero). Signed-off-by: NDimitri Sivanich <sivanich@sgi.com> Signed-off-by: NChristoph Lameter <cl@linux-foundation.org> Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Mel Gorman <mel@csn.ul.ie> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mike Frysinger 提交于
After the recent changes that went into mm/vmscan.c to overhaul stuff, we ended up with these warnings on no-mmu systems: mm/vmscan.c: In function `shrink_page_list': mm/vmscan.c:580: warning: unused variable `vm_flags' mm/vmscan.c: In function `shrink_active_list': mm/vmscan.c:1294: warning: `vm_flags' may be used uninitialized in this function mm/vmscan.c:1242: note: `vm_flags' was declared here This is because the no-mmu function defines page_referenced() to work on the first argument only (the page). It does not clear the vm_flags given to it because for no-mmu systems, they never actually get utilized. Since that is no longer strictly true, we need to set vm_flags to 0 like everyone else so gcc can do proper dead code elimination without annoying us with unused warnings. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Cc: David Howells <dhowells@redhat.com> Acked-by: NDavid McCullough <davidm@snapgear.com> Cc: Greg Ungerer <gerg@uclinux.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
If a kthread happens to use get_user_pages() on an mm (as KSM does), there's a chance that it will end up trying to read in a swap page, then oops in grab_swap_token() because the kthread has no mm: GUP passes down the right mm, so grab_swap_token() ought to be using it. We have not identified a stronger case than KSM's daemon (not yet in mainline), but the issue must have come up before, since RHEL has included a fix for this for years (though a different fix, they just back out of grab_swap_token if current->mm is unset: which is what we first proposed, but using the right mm here seems more correct). Reported-by: NIzik Eidus <ieidus@redhat.com> Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org> Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk> Acked-by: NRik van Riel <riel@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: sh: Fix up HAVE_PERF_COUNTERS typo. sh: Fix up more dma-mapping fallout. sh: SH7786 SMP support. sh: Wire up the uncached fixmap on sh64 as well. sh: Use local TLB flush in set_pte_phys(). sh: Provide cpu_idle_wait() to fix up cpuidle/SMP build.
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: RDMA: Add __init/__exit macros to addr.c and cma.c IB/ehca: Bump version number mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls IB/mthca: Replace dma_sync_single() use with proper functions RDMA/nes: Fix FIN state handling under error conditions RDMA/nes: Fix max_qp_init_rd_atom returned from query device IB/ehca: Ensure that guid_entry index is not negative IB/ehca: Tolerate dynamic memory operations before driver load
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits) fusion: mptsas, fix lock imbalance [SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count sd, sr: fix Driver 'sd' needs updating message scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets fc_transport: Selective return value from BSG timeout function fc_transport: The softirq_done function registration for BSG request sym53c8xx: ratelimit parity errors explain the hidden scsi_wait_scan Kconfig variable ibmvfc: Fix endless PRLI loop in discovery ibmvfc: Process async events before command responses libfc: Add runtime debugging with debug_logging module parameter libfcoe: Add runtime debugging with module param debug_logging fcoe: Add runtime debug logging with module parameter debug_logging scsi_debug: Add support for physical block exponent and alignment cnic: add NETDEV_1000 and NETDEVICES to Kconfig select cnic: Fix __symbol_get() build error. Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’" ipr: differentiate pci-x and pci-e based adapters ipr: add test for MSI interrupt support scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: asm-generic: add dummy pgprot_noncached() lib/checksum.c: fix endianess bug asm-generic: hook up new system calls asm-generic: list Arnd as asm-generic maintainer asm-generic: drop HARDIRQ_BITS definition from hardirq.h asm-generic: uaccess: fix up local access_ok() usage asm-generic: uaccess: add missing access_ok() check to strnlen_user()
-
git://linux-arm.org/linux-2.6由 Linus Torvalds 提交于
* 'kmemleak' of git://linux-arm.org/linux-2.6: kmemleak: Do not force the slab debugging Kconfig options kmemleak: use pr_fmt
-
由 Hugh Dickins 提交于
Indeed FOLL_WRITE matches FAULT_FLAG_WRITE, matches GUP_FLAGS_WRITE, and it's tempting to devise a set of Grand Unified Paging flags; but not today. So until then, let's rely upon the compiler to spot the coincidence, "rather than have that subtle dependency and a comment for it" - as you remarked in another context yesterday. Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk> Acked-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
handle_mm_fault() is now passing fault flags rather than write_access down to hugetlb_fault(), so better recognize that in hugetlb_fault(), and in hugetlb_no_page(). Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk> Acked-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://www.jni.nu/cris由 Linus Torvalds 提交于
* 'for-linus' of git://www.jni.nu/cris: CRISv10: remove redundant tests on unsigned CRISv32: irq.c - Move end brace outside #endif CRISv32: Fix potential null reference in cryptocop driver. CRISv32: Add arch optimized strcmp. CRIS: assignment/is equal confusion
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: hda - Make jack-plug notification selectable ALSA: ctxfi - Add PM support sound: seq_midi_event: fix decoding of (N)RPN events ALSA: hda - Add digital-mic support to ALC262 auto model ALSA: hda - Fix check of input source type for realtek codecs ALSA: hda - Add quirk for Sony VAIO Z21MN ALSA: hda - Get back Input Source for ALC262 toshiba-s06 model ALSA: hda - Fix unsigned comparison in patch_sigmatel.c ALSA: via82xx: add option to disable 500ms delay in snd_via82xx_codec_wait sound: fix check for return value in snd_pcm_hw_refine ALSA: ctxfi - Allow unknown PCI SSIDs ASoC: Blackfin: update the bf5xx_i2s_resume parameters ASoC: Blackfin: keep better track of SPORT configuration state
-
git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [WATCHDOG] wdt_pci.c: remove #ifdef CONFIG_WDT_501_PCI [WATCHDOG] hpwdt: Add NMI priority option [WATCHDOG] OMAP fixes: enable clock in probe, trigger timer reload [WATCHDOG] add bcm47xx watchdog driver [WATCHDOG] Freescale STMP: watchdog driver [WATCHDOG] twl4030 watchdog driver [WATCHDOG] U300 COH 901 327 watchdog driver [WATCHDOG] Add pnx833x_wdt
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6由 Linus Torvalds 提交于
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (62 commits) V4L/DVB (12131): BUGFIX: An incorrect Carrier Recovery Loop optimization table was being V4L/DVB (12130): Fix a redundant compiler warning V4L/DVB (12003): v4l2: Move bounding code outside I2C ifdef block V4L/DVB (11913): cx231xx: TRY_FMT should not actually set anything V4L/DVB (11912): em28xx: Use v4l bounding/alignment function V4L/DVB (11911): cx231xx: Use v4l bounding/alignment function V4L/DVB (11910): mt9: Use v4l bounding/alignment function V4L/DVB (11909): cx23885: Use v4l bounding/alignment function V4L/DVB (11908): w8968cf: Use v4l bounding/alignment function V4L/DVB (11907): cx88: Use v4l bounding/alignment function V4L/DVB (11906): saa7134: Use v4l bounding/alignment function V4L/DVB (11905): vivi: Use v4l bounding/alignment function V4L/DVB (11904): zoran: Use v4l bounding/alignment functiob V4L/DVB (11903): sh_mobile_ceu_camera: Use v4l bounding/alignment function V4L/DVB (11902): pxa-camera: Use v4l bounding/alignment function V4L/DVB (11901): v4l2: Create helper function for bounding and aligning images V4L/DVB (12128): v4l2: update framework documentation. V4L/DVB (12125): v4l2: add new s_config subdev ops and v4l2_i2c_new_subdev_cfg/board calls V4L/DVB (12122): pvrusb2: De-obfuscate code which handles routing schemes V4L/DVB (12121): pvrusb2: Improve handling of routing schemes ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev由 Linus Torvalds 提交于
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: don't set IORDY for reset sata_fsl: Add power mgmt support [libata] PATA driver for CF interface on AT91SAM9260 SoC [libata] beautify module parameters
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6: ide cmd64x: Remove serialize setting. ide: Take over as maintainer.
-
由 Roland Dreier 提交于
-
由 Peter Huewe 提交于
Add __init and __exit annotations to the module_init/module_exit functions from drivers/infiniband/core/addr.c and cma.c. Signed-off-by: NPeter Huewe <peterhuewe@gmx.de> Acked-by: NSean Hefty <sean.hefty@intel.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Alexander Schmidt 提交于
Increment version number for DMEM toleration. Signed-off-by: NAlexander Schmidt <alexs@linux.vnet.ibm.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 KAMEZAWA Hiroyuki 提交于
The isolated page is "cursor_page" not "page". This could cause LRU list corruption under memory pressure, caught by CONFIG_DEBUG_LIST. Reported-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: NBalbir Singh <balbir@linux.vnet.ibm.com> Tested-by: NDaisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Paul Mundt 提交于
That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right initially but I seem to have screwed it up while re-typing it out by hand on another machine when I checked it in. Hmph. Reported-by: NRobert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
- 23 6月, 2009 12 次提交
-
-
由 Catalin Marinas 提交于
Selecting DEBUG_SLAB or SLUB_DEBUG by the KMEMLEAK menu entry may cause issues with other dependencies (KMEMCHECK). These configuration options aren't strictly needed by kmemleak but they may increase the chances of finding leaks. This patch also updates the KMEMLEAK config entry help text. Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com> Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
-
由 Paul Mundt 提交于
Most architectures now provide a pgprot_noncached(), the remaining ones can simply use an dummy default implementation, except for cris and xtensa, which should override the default appropriately. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Chris Zankel <chris@zankel.net> Cc: Magnus Damm <magnus.damm@gmail.com>
-
由 Paul Mundt 提交于
commit dbe6f186 ("dma-mapping: mark dma_sync_single and dma_sync_sg as deprecated" conveniently broke every single SH build. In the future it would be great if people could at least bother figuring out how to use grep. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2 CPUs. This just wraps in to the existing SH-X3 SMP code with some minor changes for SH7786, including wiring up the IPIs properly, enabling IRQ_PER_CPU, and so forth. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
Now that sh64 also can use the uncached section, wire up the fixmap for it as well. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
set_pte_phys() presently uses the global flush_tlb_one(), which locks on SMP trying to do the IPI. As we have not even initialized the other CPUs at this point, switch to the local_ variant so the flush happens on the boot CPU. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Paul Mundt 提交于
Crib the x86 cpu_idle_wait() implementation and shove it in with the idle code, subsequently enabling ARCH_HAS_CPU_IDLE_WAIT. Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
-
由 Roel Kluin 提交于
Since dmanr is unsigned, negatives are wrapped and caught by the other test. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
-
由 Wim Van Sebroeck 提交于
Change the wdt_pci.c watchdog driver so that the code is the same for both the PCI-WDT500 as the PCI-WDT501 card. The selection of the card is now being done via the module parameter: 'type' instead of the config option CONFIG_WDT_501_PCI. Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Tom Mingarelli 提交于
Add a priority option so that the user can choose if we do the NMI first or last. Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Ulrik Bech Hald 提交于
This patch contains two fixes: 1)In omap_wdt_probe() the watchdog is reset and disabled. This requires register access and the clks needs to be enabled temporarily 2)In omap_wdt_open() the timer register needs to be reloaded to trigger a new timer value (the default of 60s) Tested on OMAP34xx platform (Zoom1) Reviewed-by: NKevin Hilman <khilman@ti.deeprootsystems.com> Signed-off-by: NUlrik Bech Hald <ubh@ti.com> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-